Vanguard*
Newbie
Offline
Activity: 53
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 19, 2017, 09:22:38 PM |
|
how to use overdrive without amd cpu???
|
|
|
|
KGV
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 19, 2017, 09:24:34 PM |
|
Yes. Win 10LTSB 470 480 580
I've been using Overdrive for the last two days and my 480 cards will not keep the voltage settings. Edit: I've just tried your technique disabling P0-P6 and the results are the same: Overdrive shows the correct voltages values (815mV) but GPU-Z or HWInfo show values from 834mv to 985mV ![Undecided](https://bitcointalk.org/Smileys/default/undecided.gif) Dosen't matter what they shows. Look for power consumption - you will see how it drops. Try it without and with Overdrive. And Overdrive keep all setting, if you do as i explain above.
|
|
|
|
Trimegistus
Legendary
Offline
Activity: 1564
Merit: 1027
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 19, 2017, 09:31:52 PM |
|
Yes. Win 10LTSB 470 480 580
I've been using Overdrive for the last two days and my 480 cards will not keep the voltage settings. Edit: I've just tried your technique disabling P0-P6 and the results are the same: Overdrive shows the correct voltages values (815mV) but GPU-Z or HWInfo show values from 834mv to 985mV ![Undecided](https://bitcointalk.org/Smileys/default/undecided.gif) Dosen't matter what they shows. Look for power consumption - you will see how it drops. Try it without and with Overdrive. And Overdrive keep all setting, if you do as i explained above. Right now I cannot measure the consumption at the wall but I believe Overdrive reads the values from the driver/API while GPU-Z and HWInfo take readings from the sensors. Therefore, regardless of what Overdrive shows, I believe nothing has changed. But hey, thanks anyway. I welcome every suggestion
|
|
|
|
|
fr4nkthetank
Legendary
Offline
Activity: 2294
Merit: 1182
Now the money is free, and so the people will be
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 02:38:15 AM |
|
Just wanted to share a little story...Oh how I love AMD drivers. I had a lonely win7 rig, which wasnt updated to DAG fix drivers. 6 gpu's rx470/480. do the simple procedure (by the way, I just set the clocks in wattman, voltage in Afterburner...seems to work fine so far unless you reboot - AB will probably have a fix for that someday) and lo and behold, only 4 gpu's work. Now I havent touched this rig in months and months, it has always been chugging along for over a year I guess. Why, Crypto gods, have you forsaken this poor lonely rig. Why ? And so I scratched my head, and thought...I am missing something here. Well 3 hours later while eating cereal I spit it out because I had a flash -
- I did not remember to apply...THE GOD DAMN 6GPU TOOL FIX. all is well now. now I can go to sleep. That is all.
|
|
|
|
Etheth1
Newbie
Offline
Activity: 1
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 03:13:28 AM |
|
Here solution if AB not works for you to lowering voltage.
Use Overdrive.
1.Start it (you see options to choose cards) choose one 2. Double click on left column P0 till P6 - DISABLE IT. 3. In P7 (that only left) set desired Freq and Voltage (that for GPU) 4. IN P1 (under MEMORY) set desired Freq 5. APPLY and SAVE as profile 123 6. Do same for all cards you have and rig (same profile name 123) 7. Test you settings (for stability) - you will se all works you GPU is UNDERVOLTED ! 8. Now you need make .BAT file and drop it to autostart (windows) For example inside bat file: OvedriveNTool.exe -p0"123" -p1"123" -p2"123" -p3"123" -p4"123 Drop a link to autostart and enjoy.
-p0 - that GPU number it goes from 0 till How many you have "123" - that a profile name that you save Names can be different, depends how you like it.
All works fine. Good Luck
Doesn't work. Verified power consumption with my killawatt. Hoping for a fix soon. The extra 300w increase for 20Mh extra isn't worth it. In the in meantime I'll keep using 9.6 with the nofee redirect.
|
|
|
|
cas33
Jr. Member
Offline
Activity: 234
Merit: 2
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 05:50:04 AM |
|
Just waiting for the new Claymore version 9.9,not installing driver until then. Too much mess,not worth it
|
|
|
|
informatuss
Newbie
Offline
Activity: 36
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 06:43:19 AM Last edit: August 20, 2017, 07:15:52 AM by informatuss |
|
Here solution if AB not works for you to lowering voltage.
Use Overdrive.
1.Start it (you see options to choose cards) choose one 2. Double click on left column P0 till P6 - DISABLE IT. 3. In P7 (that only left) set desired Freq and Voltage (that for GPU) 4. IN P1 (under MEMORY) set desired Freq 5. APPLY and SAVE as profile 123 6. Do same for all cards you have and rig (same profile name 123) 7. Test you settings (for stability) - you will se all works you GPU is UNDERVOLTED ! 8. Now you need make .BAT file and drop it to autostart (windows) For example inside bat file: OvedriveNTool.exe -p0"123" -p1"123" -p2"123" -p3"123" -p4"123 Drop a link to autostart and enjoy.
-p0 - that GPU number it goes from 0 till How many you have "123" - that a profile name that you save Names can be different, depends how you like it.
All works fine. Good Luck
Works for me just fine, thank you! EDIT: It worked on one rig but on second not...
|
|
|
|
Mapuo
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 08:12:49 AM |
|
Not working via bat file. Only with manual apply, one by one.
|
|
|
|
texv
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 10:02:01 AM |
|
don't fix what's not broken ![Wink](https://bitcointalk.org/Smileys/default/wink.gif) Yes, yes, yes ![Grin](https://bitcointalk.org/Smileys/default/grin.gif) From this moment it becomes my signature.....
|
Don't fix what's not broken
|
|
|
Teewar
Newbie
Offline
Activity: 1
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 11:06:40 AM |
|
Hello everyone,
I have problem with EthMan. It crash while ide work, sometime it work 30 minutes, another time 12 hours. I tested 2 different PC, and 3 different installation Windows 10. I tray v3.4 and v3.3. I have added 110 rings.
PC spec: CPU: G4400 Motherboard: MSI Z170 PRO Carbon RAM: 4GB SSD 120GB
Anyone know why it crash?
|
|
|
|
Ursul0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 12:34:40 PM |
|
I've updated my eth win10pro rigs(470 & 480) with custom beta dag fix and then with official beta drivers. All went fine, overall power is lower and DAG fix works well, Polaris is are back to 28 New API won't allow watttool to work, so using internal claymore's mclock/cclock does the trick running at my usual 850mv, for undervolting had to put fixed lower voltages in bios, as with original offsets it would be over 1v no matter what (AB is not a good tool to use) now -mvddc -cvddc also seem to work, not really sure how the correlation process with bios numbers work, as both my curves(bios & actual) are close yet not exact.
There's one issue that I really dislike though - FANs control. I even had to go back to 16.11.4 after switching to the AMD beta dag fix due to FANs issues on my ZEC rigs due to crazy fan speeds and unstable temps.
@Claymore can you maybe allow to set internal AMD target temperature(also min/max fan values) trough their API and let their native fan control to do its job?
|
|
|
|
KGV
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 03:03:29 PM |
|
Here solution if AB not works for you to lowering voltage.
Use Overdrive.
1.Start it (you see options to choose cards) choose one 2. Double click on left column P0 till P6 - DISABLE IT. 3. In P7 (that only left) set desired Freq and Voltage (that for GPU) 4. IN P1 (under MEMORY) set desired Freq 5. APPLY and SAVE as profile 123 6. Do same for all cards you have and rig (same profile name 123) 7. Test you settings (for stability) - you will se all works you GPU is UNDERVOLTED ! 8. Now you need make .BAT file and drop it to autostart (windows) For example inside bat file: OvedriveNTool.exe -p0"123" -p1"123" -p2"123" -p3"123" -p4"123 Drop a link to autostart and enjoy.
-p0 - that GPU number it goes from 0 till How many you have "123" - that a profile name that you save Names can be different, depends how you like it.
All works fine. Good Luck
P\S If you have DIFFERENT CARDS IN RIG or DIFFERENT SETTINGS FOR EACH CARD. You need to create OWN profile for each. 0 1 2 3 4 5 etc In Overdrive set all for card 0 then NEW (ENTER PROFILE NAME) SAVE Choose other card set all NEW (ENTER DIFFERENT PROFILE NAME) SAVE ETC So the bat file will look like OvedriveNTool.exe -p0"0" -p1"1" -p2"2" -p3"3" -p4"4" etc
|
|
|
|
rubbbio
Newbie
Offline
Activity: 20
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 04:10:56 PM |
|
Claymore, After 1-2 days main card drop to 8 mh from 26 mh in dual without asm mode, with asm mode it`s dropped in ours. Other cards is normal. In ether only seems ok too. What can be a problem? other algo also works good, no overclocking.
|
|
|
|
Skol600ml
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 04:54:55 PM |
|
Im trying to disable dualmining on a couple of gpu's to save some power, in order to add a 6th gpu. Im using an old 500W psu, so power is a limitation.
My problem is: When i put "-mode 1-12" in the "Claymore.stub.conf" file it doesnst stop dual mining on GPU1 and 2. When i change "-mode 0" to "-mode 1" its still dual mining on all gpu's.
Ive tried restarting the rig after i edit, ive tried minestop. I am using Ethos.
You can run 2 instances one dual, one single, disabling cards using -di for each. If there is no second coin pool's info, solo mode is automatic so no there i no need for "mode" command. ____ You can disable second coin manually with the numeric keyboard pressing the card's number twice.
|
|
|
|
ascaloon
Newbie
Offline
Activity: 36
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 05:05:33 PM |
|
Here solution if AB not works for you to lowering voltage.
Use Overdrive.
1.Start it (you see options to choose cards) choose one 2. Double click on left column P0 till P6 - DISABLE IT. 3. In P7 (that only left) set desired Freq and Voltage (that for GPU) 4. IN P1 (under MEMORY) set desired Freq 5. APPLY and SAVE as profile 123 6. Do same for all cards you have and rig (same profile name 123) 7. Test you settings (for stability) - you will se all works you GPU is UNDERVOLTED ! 8. Now you need make .BAT file and drop it to autostart (windows) For example inside bat file: OvedriveNTool.exe -p0"123" -p1"123" -p2"123" -p3"123" -p4"123 Drop a link to autostart and enjoy.
-p0 - that GPU number it goes from 0 till How many you have "123" - that a profile name that you save Names can be different, depends how you like it.
All works fine. Good Luck
P\S If you have DIFFERENT CARDS IN RIG or DIFFERENT SETTINGS FOR EACH CARD. You need to create OWN profile for each. 0 1 2 3 4 5 etc In Overdrive set all for card 0 then NEW (ENTER PROFILE NAME) SAVE Choose other card set all NEW (ENTER DIFFERENT PROFILE NAME) SAVE ETC So the bat file will look like OvedriveNTool.exe -p0"0" -p1"1" -p2"2" -p3"3" -p4"4" etc What about fan control in Overdrive software? They didnt work.
|
|
|
|
KGV
Newbie
Offline
Activity: 55
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 06:38:40 PM |
|
What about fan control in Overdrive software? They didnt work.
You do not need it in Overdrive. Fan controll perfectly works in AB.
|
|
|
|
mares992
Newbie
Offline
Activity: 4
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 07:52:14 PM |
|
Hello,
I'm new in this world.
I have rig with 6 x 1060 GTX, MB: H81 Pro BTC, 4GB RAM, Intel Celeron processor.
When start mining with this miner hash rate is 18mh/s per GPU. I have last version of Windows 10 Pro version 1703 and last version of NVidia driver version 385.28
When I overclock GPU result is same. Sometimes I got bluescreen with nvlddmkm.sys TDR_VIDEO_FALURE
What I need to change? Can someone help?
Thank you!
Marko S.
|
|
|
|
RuMiner
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 168
Merit: 15
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 08:50:45 PM |
|
When I overclock GPU result is same. do NOT overclock GPU, overclock memory only. my 1060 does almost 25 mh/s with +850 MHz mem
|
|
|
|
ascaloon
Newbie
Offline
Activity: 36
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 20, 2017, 09:01:52 PM |
|
What about fan control in Overdrive software? They didnt work.
You do not need it in Overdrive. Fan controll perfectly works in AB. Yes I know but I dont want to use AB if it works in Overdrive. But definitely I need to use it ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
|