[Setup & Troubleshoot] Bitmain AntMiner S1 180GH/S miner

[S4VV4S]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

[joyyen]

My antminer sticker is 192.168.1.99

[joyyen]

My antminer sticker is 192.168.1.99

and i believe new batch antminer come with this ip

[palawan]

My antminer sticker is 192.168.1.99

and i believe new batch antminer come with this ip

Did you connect the Antminer to your laptop/PC directly?  If so, you had to disconnect your PC/laptop from your network router/switch, unless you have a 2nd card?  If this is the former is the case, you need the laptop to be 192.168.1.100 so you can connect to the web page of the Antminer   http://192.168.1.99  then you can follow the guide to change it to 192.168.0.188 and other settings so it can be connected to your router/switch.

If you connected it directly to your network router/switch, same thing, just change your laptop/PC temporarily to 192.168.1.100 so you can reach the 192.168.1.99 and the rest above...

[joyyen]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

Sorry i am kinda noob here 

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port 

[palawan]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

Did you connect the Antminer to your laptop/PC directly?  If so, you had to disconnect your PC/laptop from your network router/switch, unless you have a 2nd card?  If this is the case, you need the laptop to be 192.168.1.100 so you can connect to the web page of the Antminer   http://192.168.1.99  then you can follow the guide to change it to 192.168.0.188 and other settings so it can be connected to your router/switch.

Sorry i am kinda noob here 

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port 

That's good.  You will lose connection to the internet on the PC that you change the IP settings on (this is temporary), but it will bring you to the same subnet(work) as the Antminer, and you'll be able to change the Antminer S1 to your home subnet(work).

When your PC/laptop is 192.168.1.100 connect to the Antminer and change it to:

192.168.0.188    IP address
255.255.255.0    subnet mask
192.168.0.1        IP default gateway (assuming this is your network router address)
192.168.0.255    broadcast address
8.8.8.8               DNS custom address

Make sure you save and apply and wait until it is applied successfully.  you should lose connection from the PC until you change your PC back to your regular settings (either DHCP or 192.168.0.x)

You can now connect to the Antminer S1 on  192.168.0.188   and put your miner pool settings.

Good luck.

[freebit13]

Sorry i am kinda noob here  

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port  

Change you IPV4 back to 192.168.0.188, log in to your router and change that to assign the range 192.168.1.xx, then your miner and internet will be on the same subnet. Otherwise you'll need to connect to the ant with a ethernet cable and change the Ant IPV4 to to 192.168.0.99

[S4VV4S]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

Sorry i am kinda noob here  

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port  

OK, on your PC or Laptop set the IPv4 settings to:
IP: 192.168.1.254
Subnet: 255.255.255.0
Gateway: 192.168.1.1

DIRECTLY connect your Ant to your PC or Laptop using a LAN cable.

Once you do that pwoer up your Ant, give it a minute or so.

Then from your PC or Laprtop browse to: 192.168.1.99

Then you shall see the Ant's interface.

[palawan]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

Sorry i am kinda noob here  

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port  

OK, on your PC or Laptop set the IPv4 settings to:
IP: 192.168.1.254
Subnet: 255.255.255.0
Gateway: 192.168.1.1

DIRECTLY connect your Ant to your PC or Laptop using a LAN cable.

Once you do that pwoer up your Ant, give it a minute or so.

Then from your PC or Laprtop browse to: 192.168.1.99

Then you shall see the Ant's interface

Guys, there is no need to connect directly to the Antminer from a PC/Laptop.  It's already connected to the network.

Both of my Antminer S1's never touched any PC directly, physically.  At least not on my network.  You just need to be on the same broadcast domain as 192.168.1.0/24.

[freebit13]

Guys, there is no need to connect directly to the Antminer from a PC/Laptop.  It's already connected to the network.

Both of my Antminer S1's never touched any PC directly, physically.  At least not on my network.  You just need to be on the same broadcast domain as 192.168.1.0/24.

I think that's the point here, his router is on

But my internet default gateway is 192.168.0.1

Without either directly connecting to the Ant and changing the IPV4 to 192.168.0.99, or changing the gateway to 192.168.1.1 on the router; it's not possible for the PC and the Ant to communicate AKAIK...

[klondike_bar]

Hi i am new to antminer S1 and i cannot connect my browser to 192.168.1.99 which is my antminer ip

i try to change the TCP/IPV4 to


ip address : 192.168.1.188  <--- change this to 192.168.2.188
subnet : 255.255.255.0
default gateway : 192.168.1.1  <--- change this to 192.168.2.1


prefered DNS : 8.8.8.8
alternative dns : blank


and also try the default antminer tutorial

IP Address: 192.168.2.254
Subnet: 255.255.255.0
Default Gateway: 192.168.2.1

Both also no luck can anyone please help me thank you

Then open your favorite browser and browse to: 192.168.2.254

Considering of course that your ant came with a sticker saying that the address is 192.168.2.254

If not post your Ant's sticker (IP) details here.

Did you connect the Antminer to your laptop/PC directly?  If so, you had to disconnect your PC/laptop from your network router/switch, unless you have a 2nd card?  If this is the case, you need the laptop to be 192.168.1.100 so you can connect to the web page of the Antminer   http://192.168.1.99  then you can follow the guide to change it to 192.168.0.188 and other settings so it can be connected to your router/switch.

Sorry i am kinda noob here 

The Antiner Sticker is 192.168.1.99

But my internet default gateway is 192.168.0.1

so if i change the default gateway

i try to change the TCP/IPV4 to


ip address : 192.168.1.188
subnet : 255.255.255.0
default gateway : 192.168.1.1

i lost my internet connection and yes the miner is directly connect to my router with antenna

it has  port and the ant miner is connected to the last port 

That's good.  You will lose connection to the internet on the PC that you change the IP settings on (this is temporary), but it will bring you to the same subnet(work) as the Antminer, and you'll be able to change the Antminer S1 to your home subnet(work).

When your PC/laptop is 192.168.1.100 connect to the Antminer and change it to:

192.168.0.188    IP address
255.255.255.0    subnet mask
192.168.0.1        IP default gateway (assuming this is your network router address)
192.168.0.255    broadcast address
8.8.8.8               DNS custom address

Make sure you save and apply and wait until it is applied successfully.  you should lose connection from the PC until you change your PC back to your regular settings (either DHCP or 192.168.0.x)

You can now connect to the Antminer S1 on  192.168.0.188   and put your miner pool settings.

Good luck.

clear the IPV4 BROADCAST address - this is unnecessary in 95% of home networks

[palawan]

Guys, there is no need to connect directly to the Antminer from a PC/Laptop.  It's already connected to the network.

Both of my Antminer S1's never touched any PC directly, physically.  At least not on my network.  You just need to be on the same broadcast domain as 192.168.1.0/24.

I think that's the point here, his router is on

But my internet default gateway is 192.168.0.1

Without either directly connecting to the Ant and changing the IPV4 to 192.168.0.99, or changing the gateway to 192.168.1.1 on the router; it's not possible for the PC and the Ant to communicate AKAIK...

That's why my instructions step by step to change it to his/her home network   192.168.0.x   with default gateway set to  192.168.0.1

I had to do for mine the similar steps to change to my home network 192.168.55.x  from factory defaul network of 192.168.1.x.

[tairta]

Hello, Sushi.
I paid order #100000727.
Please, close my order, and give me back my money (0,5 btc)!

My bitcoin wallet: 1MbxeDCTcY5YZCoJJpnHfs6JcVXQFBHjp

[bestbest]

Please help me.

Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 203.185.69.60
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: sent query to 203.185.69.60
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: reply from 203.185.69.60: reach 0x01 offset -7.486008 delay 15.006532 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
Fri Mar  7 20:26:33 2014 daemon.info sysinit: Alarm clock
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 203.158.111.11
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: sent query to 203.158.111.11
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 2.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 1.openwrt.pool.ntp.org to 203.185.69.60
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.185.69.60
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.158.111.11: reach 0x01 offset -7.522214 delay 15.078239 status 0x24 strat 2 refid 0xcbb9453c rootdelay 0.004685
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.158.118.2: reach 0x01 offset -0.003117 delay 0.042517 status 0x24 strat 2 refid 0xcbb9453c rootdelay 0.006317
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.185.69.60: reach 0x01 offset -0.002515 delay 0.039494 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
Fri Mar  7 20:26:48 2014 daemon.info sysinit: Alarm clock
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:27:01 2014 cron.info crond[577]: crond: user root: process already running: /usr/bin/cgminer-monitor

I read FAQ . but i don,t understand .

STEP 1 : Modify/etc/init.d/cgminer 

cnt=0
 if [ ! -f /tmp/cgminer-ntpd-done ]; then                               
               while [ "$NTPD_RET" != "0" ]; do                               
                       ntpd -d -n -q -N \                                     
                           -p 0.openwrt.pool.ntp.org \                       
                           -p 1.openwrt.pool.ntp.org \                       
                           -p 2.openwrt.pool.ntp.org \                       
                           -p 3.openwrt.pool.ntp.org                         
                               cnt=$ (($cnt+1))
                               if [ $cnt -gt 2 ];then
                                        echo cnt
                                        break
                              fi
                                                                             
                       NTPD_RET=$?                                           
               done                                                           
                                                                             
               touch /tmp/cgminer-ntpd-done                                   
       fi

STEP 2: Disable NTPD client for linux

STEP 3: Re-power antminer

Please explain me step by step.

thankyou so much.

[n3xus]

Please help me.

Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 203.185.69.60
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: sent query to 203.185.69.60
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: reply from 203.185.69.60: reach 0x01 offset -7.486008 delay 15.006532 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
Fri Mar  7 20:26:33 2014 daemon.info sysinit: Alarm clock
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 203.158.111.11
Fri Mar  7 20:26:33 2014 daemon.info sysinit: ntpd: sent query to 203.158.111.11
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 2.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 1.openwrt.pool.ntp.org to 203.185.69.60
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.185.69.60
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 0.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.158.111.11: reach 0x01 offset -7.522214 delay 15.078239 status 0x24 strat 2 refid 0xcbb9453c rootdelay 0.004685
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.158.118.2: reach 0x01 offset -0.003117 delay 0.042517 status 0x24 strat 2 refid 0xcbb9453c rootdelay 0.006317
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: reply from 203.185.69.60: reach 0x01 offset -0.002515 delay 0.039494 status 0x24 strat 1 refid 0x50505300 rootdelay 0.000000
Fri Mar  7 20:26:48 2014 daemon.info sysinit: Alarm clock
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: resolved peer 3.openwrt.pool.ntp.org to 203.158.118.2
Fri Mar  7 20:26:48 2014 daemon.info sysinit: ntpd: sent query to 203.158.118.2
Fri Mar  7 20:27:01 2014 cron.info crond[577]: crond: user root: process already running: /usr/bin/cgminer-monitor

I read FAQ . but i don,t understand .

STEP 1 : Modify/etc/init.d/cgminer 

cnt=0
 if [ ! -f /tmp/cgminer-ntpd-done ]; then                               
               while [ "$NTPD_RET" != "0" ]; do                               
                       ntpd -d -n -q -N \                                     
                           -p 0.openwrt.pool.ntp.org \                       
                           -p 1.openwrt.pool.ntp.org \                       
                           -p 2.openwrt.pool.ntp.org \                       
                           -p 3.openwrt.pool.ntp.org                         
                               cnt=$ (($cnt+1))
                               if [ $cnt -gt 2 ];then
                                        echo cnt
                                        break
                              fi
                                                                             
                       NTPD_RET=$?                                           
               done                                                           
                                                                             
               touch /tmp/cgminer-ntpd-done                                   
       fi

STEP 2: Disable NTPD client for linux

STEP 3: Re-power antminer

Please explain me step by step.

thankyou so much.

if you ssh into your antminer s1, do cat /etc/init.d/cgminer
does it match what you provided?
An easier way to fix your problem might be just to upgrade the firmware. What version are you running ?

[palawan]

Please help me.

....
Please explain me step by step.

thankyou so much.

if you ssh into your antminer s1, do cat /etc/init.d/cgminer
does it match what you provided?
An easier way to fix your problem might be just to upgrade the firmware. What version are you running ?

I think some other users solved a similar problem related to ntpd by upgrading the firmware.  Here's a step-by-step YouTube video on how to upgrade the Antminer S1 firmware...

https://bitcointalk.org/index.php?topic=460392.msg5081938#msg5081938

[bestbest]

my version

Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #10 Thu Dec 26 09:03:53 CST 2013

i,m update firmware already but

it,s not change. ( version firmware notchange )

please tell me step by step

i can ssh to my antminer

please

[n3xus]

my version

Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #10 Thu Dec 26 09:03:53 CST 2013

i,m update firmware already but

it,s not change. ( version firmware notchange )

please tell me step by step

i can ssh to my antminer

please

You are one version behind use this link to download the latest image
https://github.com/AntMiner/AntGen1/tree/master/firmware

[palawan]

my version

Linux version 3.10.12 (xxl@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38031) ) #10 Thu Dec 26 09:03:53 CST 2013

i,m update firmware already but

it,s not change. ( version firmware notchange )

please tell me step by step

i can ssh to my antminer

please

Hi, did you follow the step-by-step youtube Video?  Thanks.

 Upgrade the firmware on the Antminer S1

[bestbest]

i follow youtube video step by step already. but

yes i do.

update version 20140207 but it,s not change when i check in kernal log

( i cannot checksum )

but complete proceed but not change

thanks