CYPER
|
|
February 13, 2014, 07:54:56 PM |
|
Hi guys,
Need some help with accessing my configuration page on a new AntMiner. I already tried changing my IP address setting by following instruction that were mentioned in this topic and still no luck. I just can't seem to login to my little Ant. I tired using IP scanner tool while my Ant was connected and it showed nothing. Is it worth trying to reset it? I'm also unable to find a reset button on my unit, must be blind.
Thanks
I had the same problem - reconnected all the cables + reset and it appeared. The reset button is extremely small - located at the bottom middle of the small controller board
|
|
|
|
samsonn25
|
|
February 13, 2014, 07:57:14 PM |
|
Hi guys,
Need some help with accessing my configuration page on a new AntMiner. I already tried changing my IP address setting by following instruction that were mentioned in this topic and still no luck. I just can't seem to login to my little Ant. I tired using IP scanner tool while my Ant was connected and it showed nothing. Is it worth trying to reset it? I'm also unable to find a reset button on my unit, must be blind.
Thanks
I had the same problem - reconnected all the cables + reset and it appeared. The reset button is extremely small - located at the bottom middle of the small controller board Its so small its physically hard to make it any smaller. LOL
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 13, 2014, 08:26:35 PM Last edit: February 13, 2014, 09:05:36 PM by TheLomo |
|
Hi guys,
Need some help with accessing my configuration page on a new AntMiner. I already tried changing my IP address setting by following instruction that were mentioned in this topic and still no luck. I just can't seem to login to my little Ant. I tired using IP scanner tool while my Ant was connected and it showed nothing. Is it worth trying to reset it? I'm also unable to find a reset button on my unit, must be blind.
Thanks
I had the same problem - reconnected all the cables + reset and it appeared. The reset button is extremely small - located at the bottom middle of the small controller board Ty for the advice. I managed to login. Changed IP to 192.168.1.254 perfect
|
|
|
|
Darthswan
|
|
February 13, 2014, 10:03:37 PM |
|
For the people who are concerned about the heat, put a fan on the back on the miner to pull the hot air out. I'm overclocked with temps around 45/46. When my next miner comes, i'm stacking them and will have a fan also running across the blades. Would love to get it down under 40C.
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 13, 2014, 11:38:44 PM |
|
Need help getting my Ant online. I got lost with my IP settings and also don't understand the difference between having my Ant plugged directly to Computer or plug it to my Internet Router. This is what I see: https://i.imgur.com/6WDxnJm.jpg
|
|
|
|
Darthswan
|
|
February 13, 2014, 11:56:36 PM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 12:11:28 AM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
Done, just updated. My miner is directly connected to computer right now. Is this they right thing?
|
|
|
|
Darthswan
|
|
February 14, 2014, 12:12:22 AM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
Done, just updated. My miner is directly connected to computer right now. Is this they right thing? Yep, set your miner config.
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 12:30:49 AM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
Done, just updated. My miner is directly connected to computer right now. Is this they right thing? Yep, set your miner config. nah. nothing happens. I want to punch my cat in the face now
|
|
|
|
samsonn25
|
|
February 14, 2014, 12:36:28 AM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
Done, just updated. My miner is directly connected to computer right now. Is this they right thing? Yep, set your miner config. nah. nothing happens. I want to punch my cat in the face now It might not update fully until you reboot the system. Try that. Or power off and back on.
|
|
|
|
Gamer67
Sr. Member
Offline
Activity: 294
Merit: 250
тσ ¢σιи σя иσт тσ ¢σιи?
|
|
February 14, 2014, 12:46:11 AM |
|
Ipv4 gateway 192.168.1.254 Ipv4 broadcast 192.168.1.255 Custom dns 8.8.8.8
Done, just updated. My miner is directly connected to computer right now. Is this they right thing? Yep, set your miner config. nah. nothing happens. I want to punch my cat in the face now No, after you set the IP details and miner details you then connect the miner to your router/internet.
|
"I am not Dorian Nakamoto."
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 01:00:39 AM |
|
I used above setting as suggested and when I connect my miner to the interent router nothing happens and I no longer can access configuration window. What would be the process of just leaving my ant plugged in to computer and not to router? I guess I'm doing something totally wrong. If you go for a reset button will I lose all my settings?
|
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 01:17:32 AM |
|
these are all my settings: https://i.imgur.com/iW6eMjb.jpgdoes it look good? *Local Area Connection 2, is there my Miner plugged in
|
|
|
|
Unacceptable
Legendary
Offline
Activity: 2212
Merit: 1001
|
|
February 14, 2014, 01:18:08 AM Last edit: February 14, 2014, 01:33:50 AM by Unacceptable |
|
I used above setting as suggested and when I connect my miner to the interent router nothing happens and I no longer can access configuration window. What would be the process of just leaving my ant plugged in to computer and not to router? I guess I'm doing something totally wrong. If you go for a reset button will I lose all my settings? I think I see the problem,your default gateway in that pic is 192.168. 2.1 & your miner is 192.168. 1.xxx,you need to set your computer & the miner to the same .1 or .2 as your network(router) ,what was your default gateway before you started all this .1.xxx or .2.xxx Just your PC hooked to your router............& able to connect to the internet. BTW,IPv4 is YOUR IP given by the router or network Default gateway is the IP of your router,I think I got that right Looking from your PC in the CMD window,that is supposed to be YOUR router......... Yeah,reset will return your miner to whatever IP is written & all settings resort back to default,may be a good idea to start over anyway
|
"If you run into an asshole in the morning, you ran into an asshole. If you run into assholes all day long, you are the asshole." -Raylan Givens Got GOXXED ?? https://www.youtube.com/watch?v=9KiqRpPiJAU&feature=youtu.be"An ASIC being late is perfectly normal, predictable, and legal..."Hashfast & BFL slogan
|
|
|
palawan
|
|
February 14, 2014, 01:33:19 AM |
|
these are all my settings: does it look good? *Local Area Connection 2, is there my Miner plugged in On your computer that you're typing the message to us here at bitcointalk. on the command prompt type: and post the result here. I have a feeling your network is 10.1.1.x network. The other LAN card, but I could be wrong. in which case, you have to change the miner to: 10.1.1.88 255.255.255.0 10.1.1.1 (ip default gateway) DNS 8.8.8.8 broadcast 10.1.1.255 but after confirming the result of your tracert (trace route is what it stands for)
|
halu
|
|
|
Unacceptable
Legendary
Offline
Activity: 2212
Merit: 1001
|
|
February 14, 2014, 01:38:46 AM |
|
So he's got 2 networks I'll be watching,maybe I'll actually learn something My CMD just shows 1 Ethernet Adapter Local Area Connection..................
|
"If you run into an asshole in the morning, you ran into an asshole. If you run into assholes all day long, you are the asshole." -Raylan Givens Got GOXXED ?? https://www.youtube.com/watch?v=9KiqRpPiJAU&feature=youtu.be"An ASIC being late is perfectly normal, predictable, and legal..."Hashfast & BFL slogan
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 01:41:19 AM |
|
Ok just done a reset. This is what it looks now after a reset: https://i.imgur.com/2oVq65L.jpgIPv4 address is what i see on a sticker now What should I put in now? PS Thanks for trying to help out guys. I know its hard
|
|
|
|
palawan
|
|
February 14, 2014, 01:48:07 AM |
|
Ok just done a reset. This is what it looks now after a reset: IPv4 address is what i see on a sticker now What should I put in now? PS Thanks for trying to help out guys. I know its hard Not hard at all. on the PC connected to the internet, did you type the command I told you? There's no way on the PC that you can get out to the internet on 192.168.1.x reason being that's a class C subnet that can only get out of the broadcast domain through a layer 3 device (gateway/router) and 192.168.2.1 is not on the same subnet and cannot be reached. I suspect that you connected your antminer to a 2nd NIC on the PC and tried to follow the guide. You're still able to communicate to us here coz your LAN 10.1.1.2 is connected to your router 10.1.1.1 ip default gateway. but I need confirmation or I'm talking out of my ass, hence the tracert result. For all I know, you have another NIC (wifi) on that PC. I is a Network Engineer on my day job
|
halu
|
|
|
TheLomo
Newbie
Offline
Activity: 10
Merit: 0
|
|
February 14, 2014, 01:49:47 AM |
|
|
|
|
|
|