roy7
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 02, 2014, 01:49:43 PM |
|
Don't you have to send it back first to get a replacement?
You do with bitmaintech, yeah. I assumed (wrongly?) the deposit was an alternative to sending first. ie: Request replacement, send deposit, get replacement, return defective, return deposit.
|
|
|
|
freddyfarnsworth
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 02, 2014, 08:21:45 PM |
|
got my third and fourth machines today one works fine the other seems to have a dead ethernet card. any info on trouble shooting it, thanks
yeah fairly desperate .
Dead or Malfunctioning? I just received my second two and they set up ok but next morning one had 8 X's (reboots got it to 1) and then login issues with the ant and putty. I followed these steps precisely again and again and never in the same order: Turn the power supply off and on Fiddle with the jumper on the 24 pin plug Hot reinsert the power connectors and jiggle to ensure good contact Reinsert the ethernet cable and jiggle. Push the reset button for 4 seconds while everything is on. Push the reset button for 20 seconds while everything is off. Shut down and swap power connectors Push and Jiggle data connectors Learn a new kind of patience. I gave up and walked away, minutes later the thing sprang to life. Its now clocked at 400 and no X's or overheat. Go figure ![Cheesy](https://bitcointalk.org/Smileys/default/cheesy.gif) dead. this never lites and it lites on the other three units img -snip- and the RMA process offered was not acceptable. in order to get a replacement controller/ethernet card cross shipped I was asked to send them a 1.35btc deposit. considering that a complete new machine is 1.37 btc asking 1.35 btc to get the part sent first is wrong. I then feared what if there is another problem. I spent a long time looking at the machine and found other problems. see below. So i have a brick the loose cap this is a problem img -snip- crooked solder job but most likely not a problem img -snip- crooked solder job this looks like it may be a problem img -snip- [/quote] Phillip, have you thought about Litefoot ? I think he said he was interested in these ants, if he did something with this on a new thread you may get back a 250ghz unit when he is done. I could not afford to do this, could you ? freddy PS thanks for the pix, interesting to see the boards close up, the crocked chokes and cap are not the issue, I suspect the network asic but I am no litefoot ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
BTC: 1F1X9dN2PRortYaDkq89YJDbQ72i3F5N3h MEOW: KAbvy9jrrajvN5WLo7RWBsYqYfJKyN9WLf DOGE: DAyKSrTiVeRZaReTu1Cyf5Je6qPdKTuKKE
|
|
|
deagel
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 67
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 02:45:25 PM |
|
Hi, i need to setup my antminer s1 behind a http proxy.
did anybody know how to do the setup?
|
|
|
|
|
Aexcu
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 04:59:35 PM |
|
I have several BITMAIN AntMiner S1's and only one of them has this problem: 1) Turning power ON, FAN of AntMiner starts to immediately boost at full power. Effectively this means that it is loudest of the bunch as other AntMiner units control FAN speeds O.K. 2) In the AntMiner 'miner status' -window the RPM speeds seem to change, unfortunately to no effect of the FAN itself 3) Updating firmware of the unit to the latest did not help this problem (did 4) According to BITMAIN suggestion, I bought a new FAN from the internet as replacement, as suspected PWM being faulty. Unfortunately, new FAN experiences the very same issue, starts at full boost at power ON and continues ever since 5) I tried swapping the wiring (blue/white) of the connector(s), should there be an issue of factory wiring at the other end of connector but to no avail Any ideas what to try next?
|
|
|
|
ITGeniusGuru
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 06:34:46 PM |
|
![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.btc-mart.com%2F4PinMolexto6PinPCIe.jpg&t=665&c=uOBOOo9LTsBEnA) Hey you all wire experts who've worked on the S1 power cabling. This is StarTech.com 6-Inch LP4 to 6 Pin PCI Express Video Card Power Cable Adapter (LP4PCIEXADAP) It sells for only $2.11 on Amazon Can I use it to connect the 6-pin PCI-e power connector on one of the S1 blades to two 4-pin Molex connectors coming from the PSU? I remember reading somewhere that the Molex power connectors do not carry as much power (or wattage) as the PCI-e connectors? But I am thinking all yellow wires carry 12 volts, so this should work, unless the wires over-heat? Any thoughts? help? Thanks!
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 07:05:54 PM |
|
![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.btc-mart.com%2F4PinMolexto6PinPCIe.jpg&t=665&c=uOBOOo9LTsBEnA) Hey you all wire experts who've worked on the S1 power cabling. This is StarTech.com 6-Inch LP4 to 6 Pin PCI Express Video Card Power Cable Adapter (LP4PCIEXADAP) It sells for only $2.11 on Amazon Can I use it to connect the 6-pin PCI-e power connector on one of the S1 blades to two 4-pin Molex connectors coming from the PSU? I remember reading somewhere that the Molex power connectors do not carry as much power (or wattage) as the PCI-e connectors? But I am thinking all yellow wires carry 12 volts, so this should work, unless the wires over-heat? Any thoughts? help? Thanks! Short answer: Don't use it Long Answer: I see 2 problems here 1 - This is an extremely cheap cable and I am 99.9% sure the metal strands inside are not 18AWG, so cannot carry the required current. I already had a small fire because of cables like this one. 2 - The PCI-E cable has 3x 12V circuits and the CPU cable has 4x 12V circuits. This cable will use only 2x 12V circuits coming from the PSU, so might not be enough to carry the required current even at stock settings - 13.3A
|
|
|
|
Biffa
Legendary
Offline
Activity: 3220
Merit: 1220
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 07:14:46 PM |
|
Many thanks for tutorial.. Sushi.. will apply for my new AntMiner S1
Holy shit did you have to quote the entire post?
|
|
|
|
samsonn25
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 08:04:34 PM |
|
![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.btc-mart.com%2F4PinMolexto6PinPCIe.jpg&t=665&c=uOBOOo9LTsBEnA) Hey you all wire experts who've worked on the S1 power cabling. This is StarTech.com 6-Inch LP4 to 6 Pin PCI Express Video Card Power Cable Adapter (LP4PCIEXADAP) It sells for only $2.11 on Amazon Can I use it to connect the 6-pin PCI-e power connector on one of the S1 blades to two 4-pin Molex connectors coming from the PSU? I remember reading somewhere that the Molex power connectors do not carry as much power (or wattage) as the PCI-e connectors? But I am thinking all yellow wires carry 12 volts, so this should work, unless the wires over-heat? Any thoughts? help? Thanks! Short answer: Don't use it Long Answer: I see 2 problems here 1 - This is an extremely cheap cable and I am 99.9% sure the metal strands inside are not 18AWG, so cannot carry the required current. I already had a small fire because of cables like this one. 2 - The PCI-E cable has 3x 12V circuits and the CPU cable has 4x 12V circuits. This cable will use only 2x 12V circuits coming from the PSU, so might not be enough to carry the required current even at stock settings - 13.3A I agree. I have used one of these to power one side of a regular video card (260-300 watts total), but the video card needed 2 of these. Thus 4 molex connectors for 2 6-pin pcie inputs.
|
|
|
|
freebit13
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 08:30:41 PM |
|
I have several BITMAIN AntMiner S1's and only one of them has this problem: 1) Turning power ON, FAN of AntMiner starts to immediately boost at full power. Effectively this means that it is loudest of the bunch as other AntMiner units control FAN speeds O.K. 2) In the AntMiner 'miner status' -window the RPM speeds seem to change, unfortunately to no effect of the FAN itself 3) Updating firmware of the unit to the latest did not help this problem (did 4) According to BITMAIN suggestion, I bought a new FAN from the internet as replacement, as suspected PWM being faulty. Unfortunately, new FAN experiences the very same issue, starts at full boost at power ON and continues ever since 5) I tried swapping the wiring (blue/white) of the connector(s), should there be an issue of factory wiring at the other end of connector but to no avail Any ideas what to try next? You could try switching the fan over to the other side and run it from the second blade instead... that might help...
|
Decentralize EVERYTHING!
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 08:44:46 PM |
|
![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.btc-mart.com%2F4PinMolexto6PinPCIe.jpg&t=665&c=uOBOOo9LTsBEnA) Hey you all wire experts who've worked on the S1 power cabling. This is StarTech.com 6-Inch LP4 to 6 Pin PCI Express Video Card Power Cable Adapter (LP4PCIEXADAP) It sells for only $2.11 on Amazon Can I use it to connect the 6-pin PCI-e power connector on one of the S1 blades to two 4-pin Molex connectors coming from the PSU? I remember reading somewhere that the Molex power connectors do not carry as much power (or wattage) as the PCI-e connectors? But I am thinking all yellow wires carry 12 volts, so this should work, unless the wires over-heat? Any thoughts? help? Thanks! AVOID USING THISI dont have photos of the peice to attach, but I used a component just like that (albeit $1.50 and from ebay) to run a blade of my antminer while the other blade used a normal pci cabel from the PSU. within 5minutes of turning on the supply, i smelt a burning plastic smell. by the time i crossed the room to look, a 2" fire burst out from the wires. I quickly blew it out and turned off the PSU (PSU is fine still). The wires were marked as 18AWG but upon removing the charred, molten mess of wire (the entire set of wires basically fused and/or burnt up, and melted into a nearby fan wire as well) it seems like the wire was much more likely a 20AWG or 22AWG. like yours, it drew on 2 molex connectors to an 8-pin PCI (I cut off the molex in order to run from the female PCI socket on the PSU and splice the 8 individual leads to some 14AWG wire that went the rest of the way to my antminer screw terminals) 18AWG is thin. Chinese 18AWG may be thinner and mis-labelled. AVOID USING THESE.
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 08:57:20 PM |
|
![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.btc-mart.com%2F4PinMolexto6PinPCIe.jpg&t=665&c=uOBOOo9LTsBEnA) Hey you all wire experts who've worked on the S1 power cabling. This is StarTech.com 6-Inch LP4 to 6 Pin PCI Express Video Card Power Cable Adapter (LP4PCIEXADAP) It sells for only $2.11 on Amazon Can I use it to connect the 6-pin PCI-e power connector on one of the S1 blades to two 4-pin Molex connectors coming from the PSU? I remember reading somewhere that the Molex power connectors do not carry as much power (or wattage) as the PCI-e connectors? But I am thinking all yellow wires carry 12 volts, so this should work, unless the wires over-heat? Any thoughts? help? Thanks! AVOID USING THISI dont have photos of the peice to attach, but I used a component just like that (albeit $1.50 and from ebay) to run a blade of my antminer while the other blade used a normal pci cabel from the PSU. within 5minutes of turning on the supply, i smelt a burning plastic smell. by the time i crossed the room to look, a 2" fire burst out from the wires. I quickly blew it out and turned off the PSU (PSU is fine still). The wires were marked as 18AWG but upon removing the charred, molten mess of wire (the entire set of wires basically fused and/or burnt up, and melted into a nearby fan wire as well) it seems like the wire was much more likely a 20AWG or 22AWG. like yours, it drew on 2 molex connectors to an 8-pin PCI (I cut off the molex in order to run from the female PCI socket on the PSU and splice the 8 individual leads to some 14AWG wire that went the rest of the way to my antminer screw terminals) 18AWG is thin. Chinese 18AWG may be thinner and mis-labelled. AVOID USING THESE. I got some: ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FHquoeP9.jpg&t=665&c=yyxMPsfS2yRDoQ) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fyuc3DPW.jpg&t=665&c=bmtsza7DNRjB0w) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fx7lIEdh.jpg&t=665&c=3xYMBQavWWiGpg)
|
|
|
|
ITGeniusGuru
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 09:55:05 PM |
|
AVOID USING THIS
Loos like everyone agrees NOT To use this. Thank you very much everyone for advice.
|
|
|
|
Tigggger
Legendary
Offline
Activity: 1098
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 03, 2014, 10:16:58 PM Last edit: March 03, 2014, 11:24:18 PM by Tigggger |
|
Been trying to solve a problem with cgminer constantly crashing and restarting on my antminers. I've ugraded my firmware to the latest as part of my troubleshooting, and so far it's looking like it's cured the problem but... I use CGRemote to access the miner, and it's gone from Read/Write access to Read Only In my file /etc/config/cgminer I have option api_allow 'W:xxx.xxx.xxx.xxx'
So not sure why it's not working anymore. EDIT: AnswerI managed to figure it out so here's the answer in case anyone else needs it Edit /etc/init.d/cgminer Find the line that says PARAMS="$AOPTIONS $POOL1 $POOL2 $POOL3 $_pb --api-listen --api-network change to PARAMS="$AOPTIONS $POOL1 $POOL2 $POOL3 $_pb --api-listen --api-allow $_aa --api-network it will then use the option api_allow that was set in the /config/cgminer file
|
|
|
|
nitrobass24
Newbie
Offline
Activity: 2
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 02:38:09 AM |
|
|
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 02:45:29 AM |
|
|
|
|
|
V4Vendettas
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 03:25:25 AM |
|
I know this is a trouble shooting thread but I was thinking your exactly the guys and girls I should ask. Would you recomend the S1 to me ? Me: I have mined before (26 x GPU kind of ragtag setup back in 2011). I have Cold storage that all coins will be sent to and I will Hodl. I Intend to buy direct from Bitmain. Looking to get 6-8 units. Have a 3KWp solar array. Have tons of spare time on my hands to get these up and running. I will read this entire thread and any instructions I can find. Considered the X3 from black arrow but unconvinced I will get a suitable ROI. or would I be better off with other hardware ? I have one shot at recovering from my Gox loss and seriously considering this as one of my best options. ( yes I learnt my lesson no need to laugh at me ![Cry](https://bitcointalk.org/Smileys/default/cry.gif) ) Any advice or tips would be really really helpful. Respectfully V4
|
|
|
|
ITGeniusGuru
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 04:59:48 AM |
|
Considered the X3 from black arrow but unconvinced I will get a suitable ROI. or would I be better off with other hardware ?
I am anxious to read the mining veterans' advice on this. As far as I can tell, the S1 right now is the least expensive hardware. Direct from bitmain, 1.4 BTC for 180 GH/s, works out to less than $5 per GH/s (at today's BTC price - which - of course - fluctuates a lot). Compare that to what's available for IMMEDIATE DELIVERY. I suggest you stay away from "Pre"-ordering. With the only unit I - so far - have bought from bitmain, I had a good experience. Paid for it Monday evening, received it Friday afternoon. Paying with BTC eliminates the hassle of Paypal and bank wire transfers (and that's the power and beauty of BTC, isn't it?) If anyone can recommend other hardware as cheap (or even cheaper) available immediately (and so convenient to order online), I - too - would really like to know about it. I hear 1 TH/s units are coming soon from Chinese makers. Anyone knows anything about those?
|
|
|
|
snoopy_nzl
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 67
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
March 04, 2014, 05:01:39 AM |
|
I have entered pool information, worker and password, but miner status shows "section has no values" how do i "initiate" mining, start stop it? or otherwise see what error or reason it is not working? thanks!
|
|
|
|
|