Deafran
Jr. Member
Offline
Activity: 49
Merit: 4
|
|
December 14, 2020, 05:31:32 AM Last edit: December 14, 2020, 09:05:38 AM by Deafran |
|
Hello, ive a rig with 5 Cards (RX 570/470 all) and only the first main is 8 GB (the rest 4)
With rxboost 1 (or the vm comand in the correct number) without -Power + OC) i had in the past (before, in 2020 start) 26K in the main card, and 24/22/24/23 Mhz in the 4gb cards). Since the Epoch 384 and the last version of phonix, i have a lot fallen of hash rate (the 8 GB card no problem) but the rest 4 gb, all in 16K average.
I already read this was possible, so hard the fallen? can i do anything with some command?
"you can find Command-line in page 1" i am using ethos, with phoenix miner 5.3b rig xxxxxx (Ganesha) up 1 hours, 18 minutes 192.168.79.28 at http://xxxxxx.ethosdistro.comram amount: 3.8G used: 922M free: 2.9G cpu usage / temp / load: 13.7% / 36C / 0.21 0.23 0.26 63°C Fan: 2.3 Hash: 26.65 01 Ellesmere RX 470 113-D0000301_101 Samsung - 4gb 62°C Fan: 2.5 Hash: 25.36 02 Ellesmere RX 480 113-2E3471U.S5K Elpida - 4gb 59°C Fan: 2.8 Hash: 27.68 03 Ellesmere RX 480 113-2E3470U.S52 Samsung -8gb 61°C Fan: 2.7 Hash: 26.98 05 Ellesmere RX 480 113-2E3470U.X51 Samsung -8gb 106.7 hash: miner active Check out ASICseer.com S9: 16.5th at 1400W run 'helpme' to get started, root/ethos password is 'live' toggle fullscreen terminal with ctrl+alt+left/right arrow 11:24 PM ethos@xxxxxx 192.168.79.28 [106.7 hash] /home/ethos $ vi /home/ethos/local.conf loc xxxxxx Ganesha maxgputemp 80 stratumproxy miner proxywallet 0xxxxxx.Ganesha/xxxxxxxxxxxxxx@gmail.com proxypool1 eth-asia1.nanopool.org:9999 proxypool2 eth-us-east1.nanopool.org:9999 flags --cl-global-work 8192 --farm-recheck 200 globalfan 80 globalminer phoenixminer phoenixminer=flags -dagrestart 2 -gser 2 vlt xxxxxx 850 850 850 850 850 850 850 850
|
|
|
|
t-air
Newbie
Offline
Activity: 7
Merit: 0
|
|
December 14, 2020, 05:59:52 AM |
|
all my 4G only card rigs went from 170Mh/S to 102Mh/S on ETH mining, so switching to ETC, could not see that pain nomore. Bye 4G ETH mining.
|
|
|
|
bit-sokol
Newbie
Offline
Activity: 48
Merit: 0
|
|
December 14, 2020, 11:39:47 AM |
|
Rename the existing nvml.dll in System32 to something else (e.g. nvml_old.dll) then copy the one from the archive in System32. After that restart Windows, and you should be able to delete the nvml_old.dll from System32.
Please add support for DAG epoch above 500 because I'll be calm and other mining programs have already done so. +1 Phoenix may stop mining after a certain amount of time, as it did with Claymore Miner. Better to add large DAG support in advance. It would be great. Everything must be done on time. Other ethash programs already add support for the later DAG. But I chose Phoenix because many sites recommend Phoenix and there are many easy guides on how to get it running. I would like to be sure that the DAG file will last for a long time in version 5.4c (several years of mining)
|
|
|
|
kiki456
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 14, 2020, 02:30:37 PM Last edit: December 15, 2020, 01:40:16 PM by kiki456 |
|
Hi guys,
How to setup properly to write log on phoenix miner?
I try with this command
"C:\Users\Kristijan\Desktop\PhoenixMiner_5.3b\PhoenixMiner.exe" -pool eth-eu1.nanopool.org:9999 -wal 0xfdc54cbbf1be7a31ea7389683409347eb6505bc1.Worker_name/mail@mail.hr -epsw x -mode 1 -Rmode 1 -logfile *.txt -logdir "C:\Users\Kristijan\Desktop\PhoenixMiner_5.3b\log" -coin eth -rxboost 30
With this command log is normally written, but rig crashed after few hour and mining speed is smaller then usual. When i turn off write log, everythig work normally, no creshed after over 300h.
What I'm doing wrong?
I have 4x rx580 and 1x rx5700 and phoenix miner 5.3b
|
|
|
|
jgonzi
Member
Offline
Activity: 639
Merit: 19
|
|
December 14, 2020, 02:35:57 PM |
|
Hello, ive a rig with 5 Cards (RX 570/470 all) and only the first main is 8 GB (the rest 4)
With rxboost 1 (or the vm comand in the correct number) without -Power + OC) i had in the past (before, in 2020 start) 26K in the main card, and 24/22/24/23 Mhz in the 4gb cards). Since the Epoch 384 and the last version of phonix, i have a lot fallen of hash rate (the 8 GB card no problem) but the rest 4 gb, all in 16K average.
I already read this was possible, so hard the fallen? can i do anything with some command?
The best zombie Mode is lolMiner... you will get more Hashrate in theses cards... You should try them these weeks before it really goes down.
|
|
|
|
Seph213
Member
Offline
Activity: 124
Merit: 13
|
|
December 14, 2020, 07:04:26 PM |
|
Been mining for years with my 1070 using ethminer, then 3 days ago i switched over to pheonixminer .
With ethminer my core clock use would be very low and mem high .
With phoenixminer my core clock is actually being used along with mem , i almost look these same as when i’m gaming
Is that normal ? Is everyone else running 1070’s notice that ?
|
|
|
|
lgregori
Newbie
Offline
Activity: 25
Merit: 3
|
|
December 14, 2020, 09:14:17 PM |
|
Rename the existing nvml.dll in System32 to something else (e.g. nvml_old.dll) then copy the one from the archive in System32. After that restart Windows, and you should be able to delete the nvml_old.dll from System32.
Please add support for DAG epoch above 500 because I'll be calm and other mining programs have already done so. Yes! This would be very useful.
|
|
|
|
agabellini
Newbie
Offline
Activity: 11
Merit: 0
|
|
December 14, 2020, 09:33:58 PM |
|
Hello,
I'm using a little rig with an RX 470 8GB. I have about 31 MH/s.
I would like to try dual mining, and I have added this options to the command line:
-dpool blake2s.eu.nicehash.com:3361 -dwal xxxxxx -dpass x -worker xxxxxx -dcoin blake2s
It connect to nicehash and it is authorized, but the hash rate is always zero.
what am I doing wrong?
Thanks, Andrea
|
|
|
|
lastfelix
Member
Offline
Activity: 111
Merit: 10
|
|
December 15, 2020, 01:48:02 AM |
|
hello nvidia latest version problem continues even though i throw dll. is there anything else to do?
|
|
|
|
Deafran
Jr. Member
Offline
Activity: 49
Merit: 4
|
|
December 15, 2020, 02:48:34 AM |
|
Been mining for years with my 1070 using ethminer, then 3 days ago i switched over to pheonixminer .
With ethminer my core clock use would be very low and mem high .
With phoenixminer my core clock is actually being used along with mem , i almost look these same as when i’m gaming
Is that normal ? Is everyone else running 1070’s notice that ?
may i know your OS ??
|
|
|
|
Cryptomining2003
Newbie
Offline
Activity: 64
Merit: 0
|
|
December 15, 2020, 06:44:59 AM Last edit: December 15, 2020, 05:32:09 PM by Cryptomining2003 |
|
how can I use the new kernel? does it work automatically or does it need to set a parameter? Im at 20.30 in linux with amd5700
It activates automatically when needed. How can I verify which kernel is used? I didnt see any change since updating. Thx
|
|
|
|
doctorman
Newbie
Offline
Activity: 35
Merit: 0
|
|
December 15, 2020, 07:33:57 AM |
|
Using the 5.4b on my RTX 3060 ti It is very stable with full over clocking at 1500memory and -500 core , power of 66% 130W hashing at 63Mhs using older driver
Problem is if I start the Phonexminer with full over clock settings it will keep getting me Bad Shares
I have to set the MSI afterburner to memory of around +1000 all other settings the same, after few minutes I can raise it to 1500 memory and see my Hash increase.
Is there a fix for this?
Hoping for a stable restart and everything working fine instead of me intervening with each restart , windows 10 pro x64
|
|
|
|
ManuBBXX
|
|
December 15, 2020, 08:29:10 AM |
|
Using the 5.4b on my RTX 3060 ti It is very stable with full over clocking at 1500memory and -500 core , power of 66% 130W hashing at 63Mhs using older driver
Problem is if I start the Phonexminer with full over clock settings it will keep getting me Bad Shares
I have to set the MSI afterburner to memory of around +1000 all other settings the same, after few minutes I can raise it to 1500 memory and see my Hash increase.
Is there a fix for this?
Hoping for a stable restart and everything working fine instead of me intervening with each restart , windows 10 pro x64
I do 59.5 mh/s but at 50% PL, 119W + 1000Mhz, -502 core I think it's more efficient this way, give it a try and tell me your results Strange thing, if I go PL 65% like you, I have more than 130W consumed..
|
|
|
|
doctorman
Newbie
Offline
Activity: 35
Merit: 0
|
|
December 15, 2020, 08:33:52 AM Last edit: December 15, 2020, 08:45:47 AM by doctorman |
|
Using the 5.4b on my RTX 3060 ti It is very stable with full over clocking at 1500memory and -500 core , power of 66% 130W hashing at 63Mhs using older driver
Problem is if I start the Phonexminer with full over clock settings it will keep getting me Bad Shares
I have to set the MSI afterburner to memory of around +1000 all other settings the same, after few minutes I can raise it to 1500 memory and see my Hash increase.
Is there a fix for this?
Hoping for a stable restart and everything working fine instead of me intervening with each restart , windows 10 pro x64
I do 59.5 mh/s but at 50% PL, 119W + 1000Mhz, -502 core I think it's more efficient this way, give it a try and tell me your results Strange thing, if I go PL 65% like you, I have more than 130W consumed.. My problem is that the miner will fail if I start with full over clock memory but works 100% if I start with 1000 and after the first share go up to full 1500 My goal is to get max Hash that is why I went with 66% I can get 60hash at 60% that is not the issue How can I start the miner with lower mem clock and then let it go up , perhap the high mem clock messes up the auto tuning?! @PhoenixMiner seams like there is an issue with dag generation on the high mem clock, once I pass that stage , I can go as high as possible, tried it many ways , if I start on 1500mem no matter what I do the miner gets bad shares, unless I stop it , lower mem , start the file again , wait for first share or for the dag to finish
|
|
|
|
cozyfire
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 15, 2020, 08:40:04 AM |
|
Did not work for me system32 folder did not contain nvml.dll file SYSWOW64 did, I copied over dll from your archive but PhoenixMiner still can't find any cards - "No OPENCL platforms found" says the miner This post contains the instructions on how to fix the latest 460.79 Nvidia Windows driver. The reason for the problem is that one of the DLLs (nvml.dll) that the driver installs is corrupted. Here is what you have to do in order to fix the problem: File: nvml_460.79_win10.zip --------------------------- SHA-1: 749ae64e4a5044994bec61d6d94459aa4c4cc719 SHA-256: 541ccdbd77c693d1de2919adab9eaa7e2b502c9ec2f722544002abbcf643539e SHA-512: 80562b59e0a4f3c47557abc8742d9af6b119102f6fecfb3aa38112084ba0edd06451a631f633b667d57ec0417eb0db551d4cc5df90e0b835bce212b3ee6b75ce - Extract the file nvml.dll from the .zip archive you have downloaded in the previous step, and then copy it to the folder C:\Windows\System32. There will be a file with the same name here, so you have to overwrite it (you will be prompted by Windows are you sure, blah, blah, blah)
Note that this .dll is the original .dll from Nvidia (it is still digitally signed by them). If you are really paranoid, you can download 460.79 drivers from Nvidia, then use 7zip to open the .exe and extract the dll (you will find it at 460.79-desktop-win10-64bit-international-dch-whql.exe\Display.Driver\nvml.dll), and then copy it to the C:\Windows\System32 folder.
|
|
|
|
UselessGuru
Jr. Member
Offline
Activity: 200
Merit: 3
|
|
December 15, 2020, 12:06:35 PM |
|
Did not work for me system32 folder did not contain nvml.dll file SYSWOW64 did, I copied over dll from your archive but PhoenixMiner still can't find any cards - "No OPENCL platforms found" says the miner This post contains the instructions on how to fix the latest 460.79 Nvidia Windows driver. The reason for the problem is that one of the DLLs (nvml.dll) that the driver installs is corrupted. Here is what you have to do in order to fix the problem: File: nvml_460.79_win10.zip --------------------------- SHA-1: 749ae64e4a5044994bec61d6d94459aa4c4cc719 SHA-256: 541ccdbd77c693d1de2919adab9eaa7e2b502c9ec2f722544002abbcf643539e SHA-512: 80562b59e0a4f3c47557abc8742d9af6b119102f6fecfb3aa38112084ba0edd06451a631f633b667d57ec0417eb0db551d4cc5df90e0b835bce212b3ee6b75ce - Extract the file nvml.dll from the .zip archive you have downloaded in the previous step, and then copy it to the folder C:\Windows\System32. There will be a file with the same name here, so you have to overwrite it (you will be prompted by Windows are you sure, blah, blah, blah)
Note that this .dll is the original .dll from Nvidia (it is still digitally signed by them). If you are really paranoid, you can download 460.79 drivers from Nvidia, then use 7zip to open the .exe and extract the dll (you will find it at 460.79-desktop-win10-64bit-international-dch-whql.exe\Display.Driver\nvml.dll), and then copy it to the C:\Windows\System32 folder. >> "No OPENCL platforms found" says the miner What does GPU-Z say? Is OpenCL enabled on all cards? If not then you have driver install problem -> Uninstall current driver with DDU, reboot, install driver again
|
Co-developer of www.nemosminer.com (http://www.nemosminer.com)
|
|
|
devivier
Newbie
Offline
Activity: 36
Merit: 0
|
|
December 15, 2020, 01:30:16 PM Last edit: December 15, 2020, 02:45:06 PM by devivier |
|
i have exactly the same thing no nvml.dll in system 32. i have driver 356.71 I uninstall with dudu and deactivate antivirus but no dll maybe this dll comes with the new drivers
I downloaded the dll and I put it in the system 32 folder on veras but I keep the drivert 456.71 better performance for my rtx 2060 and gtx 1060 and 1660 ti in 6go
|
|
|
|
cozyfire
Newbie
Offline
Activity: 14
Merit: 0
|
|
December 15, 2020, 02:59:39 PM |
|
Other miners work well. I'm, running NBminer right now. Games are working too. It says Phoenix Miner 5.3b Windows/msvc - Release build -----------------------------------------------
CUDA version: 11.0, CUDA runtime: 8.0 No OpenCL platforms found Available GPUs for mining: GPU1: GeForce GTX 1070 Ti (pcie 9), CUDA cap. 6.1, 8 GB VRAM, 19 CUs
Did not work for me system32 folder did not contain nvml.dll file SYSWOW64 did, I copied over dll from your archive but PhoenixMiner still can't find any cards - "No OPENCL platforms found" says the miner This post contains the instructions on how to fix the latest 460.79 Nvidia Windows driver. The reason for the problem is that one of the DLLs (nvml.dll) that the driver installs is corrupted. Here is what you have to do in order to fix the problem: File: nvml_460.79_win10.zip --------------------------- SHA-1: 749ae64e4a5044994bec61d6d94459aa4c4cc719 SHA-256: 541ccdbd77c693d1de2919adab9eaa7e2b502c9ec2f722544002abbcf643539e SHA-512: 80562b59e0a4f3c47557abc8742d9af6b119102f6fecfb3aa38112084ba0edd06451a631f633b667d57ec0417eb0db551d4cc5df90e0b835bce212b3ee6b75ce - Extract the file nvml.dll from the .zip archive you have downloaded in the previous step, and then copy it to the folder C:\Windows\System32. There will be a file with the same name here, so you have to overwrite it (you will be prompted by Windows are you sure, blah, blah, blah)
Note that this .dll is the original .dll from Nvidia (it is still digitally signed by them). If you are really paranoid, you can download 460.79 drivers from Nvidia, then use 7zip to open the .exe and extract the dll (you will find it at 460.79-desktop-win10-64bit-international-dch-whql.exe\Display.Driver\nvml.dll), and then copy it to the C:\Windows\System32 folder. >> "No OPENCL platforms found" says the miner What does GPU-Z say? Is OpenCL enabled on all cards? If not then you have driver install problem -> Uninstall current driver with DDU, reboot, install driver again
|
|
|
|
DejavuUS
Newbie
Offline
Activity: 6
Merit: 0
|
|
December 15, 2020, 03:46:41 PM |
|
Is PhoenixMiner 5.4b legit, I dont see it mentioned here and when I downloaded it from the github page windows deleted a virus "Contebrew.A!ml" in the Phoenixminer.exe file Is this normal?
|
|
|
|
duplj30
Newbie
Offline
Activity: 18
Merit: 0
|
|
December 15, 2020, 03:53:59 PM |
|
Is PhoenixMiner 5.4b legit, I dont see it mentioned here and when I downloaded it from the github page windows deleted a virus "Contebrew.A!ml" in the Phoenixminer.exe file Is this normal?
just above the link to mega.nz, download from there
|
|
|
|
|