s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 09:56:16 AM |
|
3 more antminer S1 units came in today - 4.5TH ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FiPQxGKH.jpg&t=665&c=Mg355U9KY-69LA) however, 1 unit arrived with a lot of thermal paste leakage, and another took damage to the capacitor (see pic below). ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FzcEmyue.jpg&t=665&c=iJiSayVIJXKteg) Right now i am running it with the capacitor pulled off fully (cleanly removed, it practically fell off on its own when i reached in to grab it out with a pair of tweezers) and 16 of the chips on that board show 'x' and the hashrate of the unit (stock clocks) is 155GH. Rebooting is a crapshoot of anything from all 36 working down to only 2 or 3 working. should be a clean and easy fix monday - I dont trust my precision soldering enough to DIY a small component, and my base of operations has someone capable Nice setup, can you advice whats you using on side of S1? is it wooden board or plexi glass ?
|
|
|
|
allcoinminer
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 11:35:48 AM Last edit: May 03, 2014, 02:37:12 PM by allcoinminer |
|
I like to order 2 more S1 anticipating ROI. Can anyone give you account after removing all your personal data for coupon use? I have never had an email from Bitmain, Ants always arrive, you can log in to your account and check the status of payment/shipping. Tracking number usually showing up within 1-2 days of order.
|
|
|
|
oskuro
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 12:46:43 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
|
|
|
|
s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 12:48:55 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp
|
|
|
|
oskuro
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:10:24 PM Last edit: May 03, 2014, 01:21:16 PM by oskuro |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp Mmm but i read that corsair can run up to 2 s1s, its not a better option than that Dell? Just comparing prizes maybe yeah its cheaper but its a good psu? And can run 2 s1s? And that dell psu comes with conectores for s1 or i need to buy cables?
|
|
|
|
bobsag3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:20:11 PM |
|
Does Anyone have an extra coupon for a S2 in Dallas, TX area that they can spare??? Someone trustworthy. Kindly would appreciated.
I do.
|
|
|
|
oskuro
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:26:36 PM |
|
Whats the point buying piece of pcb which cost more than psu? I dont get it, check this: ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FDP2pBiH.jpg&t=665&c=qFNEHHKPz3qgxQ) Cables costs: 2gbp psu cost is :12gbp You can plug up to 2 units on one PSU by them cables. All my PSU have mods to slow the fan. As original one are sooo loud. No issues what so ever. Where can i buy then necessary cables for using dell with s1? . And u know how much kw/h consumes s1 with that dell psu? ?
|
|
|
|
Threader
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:29:29 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp The more powerful versions of those server power supplies (2000w) that can handle 3-4 S1s are the only way to go if you have an isolated remote set-up where jetnoise is a non issue because the cost advantage over ATX form factor power supplies is huge. On the other hand if your just looking to power 1 or 2 S1's in your house I would rather go the with an ATX PS that just plugs right in without the need for adapters or soldering wires, is quiet and can be reused for other things or easily sold.
|
|
|
|
wpgdeez
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:53:07 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp If you are running the miner in your house the Dell PSU is loud! I like the eVGA 1300 watt. It will run 3 oc ants and can be found for $200 or less and is silent.
|
|
|
|
oskuro
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 01:59:53 PM |
|
Ok thanks guys. Right now i Will have 1 and in my bedroom so better a quiet psu like corsair xD
|
|
|
|
s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 02:11:27 PM Last edit: May 03, 2014, 08:34:54 PM by s1lverbox |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp If you are running the miner in your house the Dell PSU is loud! I like the eVGA 1300 watt. It will run 3 oc ants and can be found for $200 or less and is silent. Not true, please find thread about adding 47ohm resistor to fan in psu. I wil add video shortly of 3 dell units and noise what they makingVideo showing 3 units on test bench in spare room: https://www.youtube.com/watch?v=uHz2XERDvak&feature=youtu.beIBM 2000w can be grabbed for like $60 and you talking about psu for $200. obviously you doing this as hobby.
|
|
|
|
s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 02:28:22 PM |
|
Whats the point buying piece of pcb which cost more than psu? I dont get it, check this: ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FDP2pBiH.jpg&t=665&c=qFNEHHKPz3qgxQ) Cables costs: 2gbp psu cost is :12gbp You can plug up to 2 units on one PSU by them cables. All my PSU have mods to slow the fan. As original one are sooo loud. No issues what so ever. Where can i buy then necessary cables for using dell with s1? . And u know how much kw/h consumes s1 with that dell psu? ? This is on my psu- cables done myself. Overal cost was like 5 gbp per pair
|
|
|
|
s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 02:32:26 PM Last edit: May 03, 2014, 08:34:21 PM by s1lverbox |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp The more powerful versions of those server power supplies (2000w) that can handle 3-4 S1s are the only way to go if you have an isolated remote set-up where jetnoise is a non issue because the cost advantage over ATX form factor power supplies is huge. On the other hand if your just looking to power 1 or 2 S1's in your house I would rather go the with an ATX PS that just plugs right in without the need for adapters or soldering wires, is quiet and can be reused for other things or easily sold. This jet noise is easy to work around with adding resistor 47ohm to red wire on psu fan. This resistor will lower speed about 2/3 which is more than enough cool and keep noise down.
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 03:02:37 PM |
|
3 more antminer S1 units came in today - 4.5TH ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FiPQxGKH.jpg&t=665&c=Mg355U9KY-69LA) however, 1 unit arrived with a lot of thermal paste leakage, and another took damage to the capacitor (see pic below). Nice setup, can you advice whats you using on side of S1? is it wooden board or plexi glass ? a few units i cut out some thin cardboard (the type for frozen pizza boxes) in the right shape to fit well on the gap of the antminer and try to improve the airflow going through the entire length. It works, but I really want to make myself some exact measurements and make more of them properly using thicker cardboard or even some very thin plywood/plastic that will be less flimsy. the satck of 3 units just has a big box lid pressed against it, held in place by the power supplies. it does a nice job at getting the temperatures down slightly. I plan to add to these stacks a little bit soon once i figure out some more power supplies that use PCIe cables (since when stacked the screw terminals are inaccessible)
|
|
|
|
samsonn25
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 03:42:17 PM Last edit: May 03, 2014, 03:56:29 PM by samsonn25 |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp If you are running the miner in your house the Dell PSU is loud! I like the eVGA 1300 watt. It will run 3 oc ants and can be found for $200 or less and is silent. Not true, please find thread about adding 47kohm resistor to fan in psu. I wil add video shortly of 3 dell units and noise what they makingVideo showing 3 units on test bench in spare room: https://www.youtube.com/watch?v=uHz2XERDvak&feature=youtu.beIBM 2000w can be grabbed for like $60 and you talking about psu for $200. obviously you doing this as hobby. 2000 watts on high end platinum psus can save $500+ in a year in electricity costs if your running it close to max 24/7. Check the efficiency on some of the server psus you guys are talking about.
|
|
|
|
Biodom
Legendary
Offline
Activity: 3864
Merit: 4261
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 03:51:15 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp Mmm but i read that corsair can run up to 2 s1s, its not a better option than that Dell? Just comparing prizes maybe yeah its cheaper but its a good psu? And can run 2 s1s? And that dell psu comes with conectores for s1 or i need to buy cables? Not really re running two S1 on one CX750, especially if you want to overclock to 393.75mhz (~420-425W) or even 375mhz (~400W). I run three overclocked S1 on two Corsair CX750M. For an individual S1, Corsair CX500 or CX500M would do.
|
|
|
|
vodic62
Newbie
Offline
Activity: 11
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 07:14:27 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp The more powerful versions of those server power supplies (2000w) that can handle 3-4 S1s are the only way to go if you have an isolated remote set-up where jetnoise is a non issue because the cost advantage over ATX form factor power supplies is huge. On the other hand if your just looking to power 1 or 2 S1's in your house I would rather go the with an ATX PS that just plugs right in without the need for adapters or soldering wires, is quiet and can be reused for other things or easily sold. This jet noise is easy to work around with adding resistor 47kohm to red wire on psu fan. This resistor will lower speed about 2/3 which is more than enough cool and keep noise down. 47 kOhm is nonsense. You probably mean 47 Ohm... But guys, you should really care about psu efficiency, not price. If it's running 24/7, it's much more important.
|
|
|
|
s1lverbox
Legendary
Offline
Activity: 2324
Merit: 1039
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 08:33:43 PM |
|
I will receive my s1 next week, what altcoins you mine with s1? . And i want to buy a corsair cx750m is a good psu? Thanks
You will spend to much money for PSU, just go for dell poweredge 2950 750w and it will cost you like $25 or 15gbp The more powerful versions of those server power supplies (2000w) that can handle 3-4 S1s are the only way to go if you have an isolated remote set-up where jetnoise is a non issue because the cost advantage over ATX form factor power supplies is huge. On the other hand if your just looking to power 1 or 2 S1's in your house I would rather go the with an ATX PS that just plugs right in without the need for adapters or soldering wires, is quiet and can be reused for other things or easily sold. This jet noise is easy to work around with adding resistor 47kohm to red wire on psu fan. This resistor will lower speed about 2/3 which is more than enough cool and keep noise down. 47 kOhm is nonsense. You probably mean 47 Ohm... But guys, you should really care about psu efficiency, not price. If it's running 24/7, it's much more important. Snap, you right. Why i did use that kOHM i dont know. Thanks for pointing this out.
|
|
|
|
ceslick
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 161
Merit: 100
digging in the bits... now ant powered!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 03, 2014, 11:40:41 PM |
|
@Bitmain, when you shipping the next batch of orders?
|
|
|
|
mark978
Newbie
Offline
Activity: 13
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
May 04, 2014, 04:11:51 AM |
|
Looks like I have a failed ethernet port/Control board from my last batch ![Undecided](https://bitcointalk.org/Smileys/default/undecided.gif) Power the S1 up and only the green led on the ethernet port flashes. No activity from the amber light. The red led on the control board is solid, and the green led slowly pulses. Can't access the webgui or ssh in. Tried port scanning on .0.99 through .2.99 and nothing. Disconnect each blade, try swapping sides, still nothing. Here is the odd part. When I power the S1 up, about 5 minutes later the entire antfarm (9 total) will all go down, showing pool status "dead" for all of them! Unplug the ethernet for the broken one and they will all come back online, happily hashing away! Is the damaged control board sending out malformed packets? I have emailed bitmain, as I bought it direct. Hope a replacement happens quickly!
|
|
|
|
|