wispbg
Newbie
Offline
Activity: 3
Merit: 0
|
|
August 11, 2017, 06:37:46 PM |
|
hi boss, is there any desired value for -dcri in claymore 9.8 for rx580? when claymore mining eth only, my rx580 runs at 28mh. when dual mining eth+sc, i got 24mh eth + 700mh sc. decreasing -dcri value from 30 to 20 only decreases eth hash to 22mh.
any help? thanks
Right now the best -dcri is 14-16. Try +- for best tunning. Got several right with 580-4g and 15 is my number. Hope itll work for you too!
|
|
|
|
WhyMe
|
|
August 11, 2017, 06:42:49 PM |
|
Hi,
Firstly, i apologize for my poor English. I do Ethereum mining with 1x R9 280X Dual-X model GPU, but I get a lower performance than other miners with same GPU. I get about 14.550 Mh/s. Is it normal for R9 280x or am i doing something wrong? Thank you.
--------
OC values I used; 1220 MHz GPU Clock // 1500 MHz Memory Clock.
GPU Driver Version; Crimson ReLive 17.7.2
Rig Specs;
AMD fx-6100 600W Power Supply 8 GB RAM
My bat file; setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool SERVER -ewal ADRESS.RIGNAME -epsw x -dcri 37 -etha 0 -asm 1
It's normal on ETH/ETC. Try UBQ/MUSIC/... and you will get 25MHs+
|
|
|
|
TheMiningDwarf
Jr. Member
Offline
Activity: 71
Merit: 1
|
|
August 12, 2017, 01:57:40 AM |
|
Anyone have experience with altering the ETH intensity?
-ethi Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6". You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.
I understand that default is "8", and I also see that "0" is the lowest, but it does not mention the highest setting. I suppose that's when your system crashes or becomes unusable?
Is there a benefit to changing from default in your experiences?
The example above which discusses setting intensity for every card individually ("-ethi 1,8,6") --- Is the first number the desired intensity, and it applies that to cards 8 and 6? I just need a little clarification on that point.
THANKS
The benefit is you increase your mining speed But I noticed not every card respond the same way So you should increase it 1 card at a time and see the improvement and make sure its stable Then go card 2 and 3 etc you can do all at the same time, but you might have all card at intensity let say 4 cause the weakess card crash above that, while some of your other cards can be increased more.
|
|
|
|
TheMiningDwarf
Jr. Member
Offline
Activity: 71
Merit: 1
|
|
August 12, 2017, 02:05:12 AM |
|
I have a 12 GPU rig (RX480 x6 , 1070 x6 )with mb tb250 BTC PRO. and I have a problem here.
when I ran claymore 9.8 it will freeze at the begining,while it detect gpu. I try several way and cannot solve this problem.
at the end I try to use -di option and separate claymore to 3 windows and its work (rx480x3)+(rx480x3)+(1070x6) .
but it may consume more ram, I guess?
so my question is how to run a single claymore to support all my 12 gpu card.
Thank you.
my rig detail is
tb250 btc pro celeron g3900 ram 4gb (try to add to 12gb of ram and still freeze) red devil RX480 8G (several driver / fix dag driver all the same) palit 1070gtx 8gb cougar psu 1050w gold x2 riser ver.5 , 6 , 7 windows 10 pro latest update
Whats your command string ? Have you try -gser : this setting can improve stability on multi-GPU systems if miner hangs during startup. It serializes GPUs initalization routines. Use "-gser 1" to serailize some of routines and "-gser 2" to serialize all routines. Are you using fast AMD kernel option can be many thing Best thing is to start your miner with the minimum options in your string and go from there But for me the -gser command solved that problem Hope it helps
|
|
|
|
lmlim
Newbie
Offline
Activity: 16
Merit: 0
|
|
August 12, 2017, 06:41:23 AM |
|
Hi,
I need help on reducing/eliminating rejection rate of second coin in dual mining. When dual mining eth + xxx, second coin always has (target) rejection rate1-4%. I am using claymore miner as a 3rd party miner in Nicehash.
According to the "interactive history chart" from nicehash web, I believe the highest rejection is "target". the second, some "stale" shares, then the third, there are very few "duplicates".
This happened to all, decred,sia,pascal,and lbry.
changing -dcri value does not matter much since it is not incorrect shares?
thank you..
|
|
|
|
Evan
|
|
August 12, 2017, 09:45:02 AM |
|
Anyone have experience with altering the ETH intensity?
-ethi Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6". You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.
I understand that default is "8", and I also see that "0" is the lowest, but it does not mention the highest setting. I suppose that's when your system crashes or becomes unusable?
Is there a benefit to changing from default in your experiences?
The example above which discusses setting intensity for every card individually ("-ethi 1,8,6") --- Is the first number the desired intensity, and it applies that to cards 8 and 6? I just need a little clarification on that point.
THANKS
THE DEFAULT IS 8-- That is also the highest setting. For individual cards, the syntax is often comma or space separated per card, depending on the mining software. The value for GPU 0 is first, then comma, then for GPU 1, then comma, then GPU2... and so forth. Claymore decided to use commas rather than spaces. If you use a negative value, you are setting a "Global Work Size", as was used in the original Ethminer. You could double, or perhaps quadruple that value, but I would not bother to use it. Single digits (integers) from 0 to 8 are much easier to type. --scryptr Please do not put out wrong information. Or Knowingly lie to users.
|
I am poor, but i do work for Coin 1PtHcavXoakgNkQfEQdvnvEksEY2NvwaLM
|
|
|
Bob_chemist
Newbie
Offline
Activity: 28
Merit: 0
|
|
August 12, 2017, 09:45:18 AM |
|
@Claymore, Can you, please, add some features to EthMan, such as: A couple of columns with wallets addresses for Eth and second coin. Or, if it's too labour intensive, then one more comment column. Sorting whole table by one of columns. Changing column's place in the table.
9.8 with unofficial Beta driver works fine, thank you!
|
|
|
|
scryptr
Legendary
Offline
Activity: 1797
Merit: 1028
|
|
August 12, 2017, 10:23:39 AM |
|
Anyone have experience with altering the ETH intensity?
-ethi Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6". You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.
I understand that default is "8", and I also see that "0" is the lowest, but it does not mention the highest setting. I suppose that's when your system crashes or becomes unusable?
Is there a benefit to changing from default in your experiences?
The example above which discusses setting intensity for every card individually ("-ethi 1,8,6") --- Is the first number the desired intensity, and it applies that to cards 8 and 6? I just need a little clarification on that point.
THANKS
THE DEFAULT IS 8-- That is also the highest setting. For individual cards, the syntax is often comma or space separated per card, depending on the mining software. The value for GPU 0 is first, then comma, then for GPU 1, then comma, then GPU2... and so forth. Claymore decided to use commas rather than spaces. If you use a negative value, you are setting a "Global Work Size", as was used in the original Ethminer. You could double, or perhaps quadruple that value, but I would not bother to use it. Single digits (integers) from 0 to 8 are much easier to type. --scryptr Please do not put out wrong information. Or Knowingly lie to users. PLEASE CORRECT ME-- I have not lied to anyone. --scryptr
|
|
|
|
Evan
|
|
August 12, 2017, 10:37:32 AM |
|
Anyone have experience with altering the ETH intensity?
-ethi Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6". You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.
I understand that default is "8", and I also see that "0" is the lowest, but it does not mention the highest setting. I suppose that's when your system crashes or becomes unusable?
Is there a benefit to changing from default in your experiences?
The example above which discusses setting intensity for every card individually ("-ethi 1,8,6") --- Is the first number the desired intensity, and it applies that to cards 8 and 6? I just need a little clarification on that point.
THANKS
THE DEFAULT IS 8-- That is also the highest setting. For individual cards, the syntax is often comma or space separated per card, depending on the mining software. The value for GPU 0 is first, then comma, then for GPU 1, then comma, then GPU2... and so forth. Claymore decided to use commas rather than spaces. If you use a negative value, you are setting a "Global Work Size", as was used in the original Ethminer. You could double, or perhaps quadruple that value, but I would not bother to use it. Single digits (integers) from 0 to 8 are much easier to type. --scryptr Please do not put out wrong information. Or Knowingly lie to users. PLEASE CORRECT ME-- I have not lied to anyone. --scryptr That is also the highest setting.Max setting for ethi is 16
|
I am poor, but i do work for Coin 1PtHcavXoakgNkQfEQdvnvEksEY2NvwaLM
|
|
|
Trimegistus
Legendary
Offline
Activity: 1564
Merit: 1027
|
|
August 12, 2017, 10:42:41 AM |
|
PLEASE CORRECT ME--
I have not lied to anyone. --scryptr
The highest setting for -ethi is 16 and not 8
|
|
|
|
scryptr
Legendary
Offline
Activity: 1797
Merit: 1028
|
|
August 12, 2017, 11:29:17 AM |
|
Anyone have experience with altering the ETH intensity?
-ethi Ethereum intensity. Default value is 8, you can decrease this value if you don't want Windows to freeze or if you have problems with stability. The most low GPU load is "-ethi 0". Also "-ethi" now can set intensity for every card individually, for example "-ethi 1,8,6". You can also specify negative values, for example, "-ethi -8192", it exactly means "global work size" parameter which is used in official miner.
I understand that default is "8", and I also see that "0" is the lowest, but it does not mention the highest setting. I suppose that's when your system crashes or becomes unusable?
Is there a benefit to changing from default in your experiences?
The example above which discusses setting intensity for every card individually ("-ethi 1,8,6") --- Is the first number the desired intensity, and it applies that to cards 8 and 6? I just need a little clarification on that point.
THANKS
THE DEFAULT IS 8-- That is also the highest setting. For individual cards, the syntax is often comma or space separated per card, depending on the mining software. The value for GPU 0 is first, then comma, then for GPU 1, then comma, then GPU2... and so forth. Claymore decided to use commas rather than spaces. If you use a negative value, you are setting a "Global Work Size", as was used in the original Ethminer. You could double, or perhaps quadruple that value, but I would not bother to use it. Single digits (integers) from 0 to 8 are much easier to type. --scryptr Please do not put out wrong information. Or Knowingly lie to users. PLEASE CORRECT ME-- I have not lied to anyone. --scryptr That is also the highest setting.Max setting for ethi is 16 THANK YOU! -- Sorry, although I have read the README!!!.txt several times, it seems that I forgot an item. Personally, I never bothered much with "-ethi", but was more concerned with "-dcri". I fiddle with my rigs around the clock, and try to keep up-to-date with the threads, like this one. If I answer someone I always try my best, but I missed this catch. Apologies!!! And, thank you for correcting me. I had the sneeking suspicion that I should have checked the README!!!.txt before I posted, but it was late. Haste makes waste. --scryptr
|
|
|
|
scryptr
Legendary
Offline
Activity: 1797
Merit: 1028
|
|
August 12, 2017, 11:30:39 AM |
|
PLEASE CORRECT ME--
I have not lied to anyone. --scryptr
The highest setting for -ethi is 16 and not 8 THANK YOU!!! -- --scryptr
|
|
|
|
nub miner
Newbie
Offline
Activity: 4
Merit: 0
|
|
August 12, 2017, 12:27:22 PM |
|
Hello everyone,
I would like to ask for some help regarding some problems i have encountered regarding Clamore OC.
i ahve rig with 5 cards, 4x Powercolor RX 580 8 GB Red Devil and 1x Sapphire RX580 8GB Nitro+(1411MHz core).
I moded bioses. and using Claymore v9.8 dual minein ETH and SC
I was playing around with OC to see my max and consumption which was 29-30MHz 140W in GPUZ and then came down to 28MHs with 110W in GPUZ.
these OC settings worked fine for 24 hours with no crashes: -dcri 21 -tstop 85 -tt 70 -fanmin 55 -fanmax 100 -cclock 1200 -mclock 2150 -cvddc 900 -mvddc 850
However i have then decided to try to lower core voltaga in steps of 10mV which got me down to 880mV on core in hopes of saving some more power and finfing lowest possible VDDC to run on.
Unfortuantelly Claymore hangs and crashes.
Upon restarting the rig, i noticed my hashraate drops down to 20 per card and checked in GPUZ whats going on. Cards do not want to accept settings from Claymore OC anymore, so i am now forced to use wattman to get them runnig at desired settings.
Claymore also stopped reporting temperatures and fanspeeds for all except 1 card. This card is also acting out and droping to 18MHS all the time causing my hash to fluctuate between 130 and 140MHs.
How do i get claymore to run normally again so i dont need to use Wattman?
|
|
|
|
doktor83
|
|
August 12, 2017, 12:34:07 PM |
|
use DDU and delete drivers, reinstall drivers, and be happy.
|
|
|
|
nub miner
Newbie
Offline
Activity: 4
Merit: 0
|
|
August 12, 2017, 12:40:48 PM Last edit: August 12, 2017, 02:46:34 PM by nub miner |
|
use DDU and delete drivers, reinstall drivers, and be happy.
Thank you for quick reply, i did that last night and it didnt help... However i have solved this issue 3 time s in the past by reflashing to stock and then back to modded bios and that is the only thing that helped, but i dont want to do that again. edit: i didnt use safemode though i am gonna tryx in safe mode right noww and come back ... edit2: i run DDU in safemode this time. it helped everything is back to normal again. thank you very much
|
|
|
|
xiekang12121
Newbie
Offline
Activity: 30
Merit: 0
|
|
August 12, 2017, 12:58:40 PM |
|
Claymore's Ethereum Miner Crack charges v7.5 ETH redirects developers to charge gadgets that are perfectly compatible with all Claymore kernel mining software. Claymore's Ethereum Mining NoDevFee v7.5 When you use Claymore's Dual Etherem Miner, This program can help you save your money and earn more. It will re-redirect 1% (or 2% of the dual mode) to the designated wallet address. download link: _________________________________________________ http://Http://pan.baidu.com/s/1slAu6cdhttp://Https://github.com/xiekang0817/NoDevFeeWhenever a developer wallet address is monitored, the developer wallet address is automatically blocked and automatically replaced with the purse address you specified. Claymore's Dual Ethereum full version crack ETH mining charge tool (redirect developer wallet address for your wallet address): Http [Suspicious link removed] -> Properties -> Compatibility tab -> Run as administrator -> Save 3) Open start.bat and change your wallet to your wallet address Demo: Code: Start NoDevFee 0xc1950f7049f576ef6966dcad20d7d3bd82c49326 4) Run the start.bat file 5) The software displays this prompt to indicate that it was running successfully. And then you can ignore him, and it is minimized. 6) At this point you can start your mining process, that is correct to start the order is: 1-> Run the redirect tool. 2-> Run your mining program. 7) After running for a while you can see from the redirect tool window that you have redirected the developer wallet to your wallet. Cool This redirected developer wallet tool is compatible with all Claymore kernel mining processes, including Claymore original, Changsha miners, China Digital Miner, Paladin, etc. All Claymore kernel mining procedures. Start the order is also the first to start the redirect tool, the second to start your mining process. Tips: _________________________________________________ This procedure to fill the eth wallet address and your mining procedures to fill the eth wallet address Consistent, can be redirected to success. Reminder: _________________________________________________ First charge the developer fee to send the fortune to your wallet address (15 minutes after the start of the program) The second real charge of the developer fee to send your fortune to your wallet address (1 hour after the start) The third charge of the developer fee to send your fortune to your wallet address (2 hours after the start of the program) Fourth, fifth, sixth, seventh and all the next devfee send shares to your wallet. 1) due to Claymore Miner developers charge rate is a single dig 1%, double dig 2%. Equal to 36 seconds to 72 seconds per hour is the cost of the developer. After running the program to be stable operation for 6 hours or more from your pool of computing power to see the obvious effect. 24 hours average effort needs 24 hours to show true computing power. There is a delay in the calculation of the power, but the calculation of the force and the calculation of income are immediate. With ETH up to 25% per month profit: _________________________________________________ http://Https://ethtrade.org/@955817
|
|
|
|
BLNT
Newbie
Offline
Activity: 31
Merit: 0
|
|
August 12, 2017, 01:07:55 PM |
|
Claymore's Ethereum Miner Crack charges v7.5
ETH redirects developers to charge gadgets that are perfectly compatible with all Claymore kernel mining software. Claymore's Ethereum Mining NoDevFee v7.5 When you use Claymore's Dual Etherem Miner, This program can help you save your money and earn more. It will re-redirect 1% (or 2% of the dual mode) to the designated wallet address.
...
Anyone else consider some cracks, this one being a good example, unethical? --- As an aside, would it be fair to assume (I've not done any research) that the Claymore miner is the best for ETH? THANKS
|
|
|
|
Fravarti
Newbie
Offline
Activity: 2
Merit: 0
|
|
August 12, 2017, 01:22:55 PM |
|
Hello Such a problem: Installed a modified AMD driver Installed the patch atikmdag-patcher-1.4.5 Launched Claymore 9.8. The result: I received an increase of 1.5-2 mh/s but ... Constantly jumps on every card from 14.5 to 30.5 mh/s, every 2 seconds
Cards Sapphire RX580 Pulse 8 gb - 6 pcs/rig
-mclock 2150
On Claymore 9.7 and the original driver 17.6.2 this did not happen
|
|
|
|
madnick
Newbie
Offline
Activity: 2
Merit: 0
|
|
August 12, 2017, 01:46:34 PM |
|
Fravarti,
did u try new beta driver with 9.7 version of claymore?
I am using v9.7 and i am stable.
Anyway guys, do u know something more about Plasma implementation ? will we be able to mine ETH with gpus after that? or i am asking something dummy thing?
|
|
|
|
nub miner
Newbie
Offline
Activity: 4
Merit: 0
|
|
August 12, 2017, 01:53:25 PM |
|
use DDU and delete drivers, reinstall drivers, and be happy.
Thank you very much i used DDU in safe mode and it helped.
|
|
|
|
|