|
Grix
|
 |
February 21, 2014, 10:48:05 PM |
|
Does anyone know whether the terrible 30-day luck statistic is caused by some problem at the pool in the last month or if it really is just terrible luck?
|
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
denisa
Newbie
 Offline
Activity: 12
Merit: 0
|
|
February 21, 2014, 10:51:51 PM |
|
Hi, i am running 2 x antminer s1
still after 25 hours in status start showing a few x oooooxoooo example...
Can somebody explain why , still after 24-25 hours and oboth same :-(
Alarm bells should be ringing if you dont see hashing after 5 minutes never mind 25 hours. There must be something wrong with your setup. With xxx still running ok i think alarm ringing after restart and than again ok You think bad oc ? Or low psu ? low psu = bad oc what psu do you have? [edit] establish whether it's harware or psu - run 1 miner not overclocked on 1 psu - you should see 180G there is no brand just oboth is 500watt i bought with this psu like complet setup with custom cooling 40c after oc i use OC from forum 500 watt is probably too low - I think you need at least a 750 - amazon sell a corsair 750 for 62-70 UKP. You'd need one of these for each of your S1s. What rate do you get with just one un-overclocked S1 connected to the 500w psu? Un oc in stock is 180 hashrate each |
|
|
|
|
denisa
Newbie
Offline
Activity: 12
Merit: 0
|
|
February 21, 2014, 11:07:18 PM |
|
Hi, i am running 2 x antminer s1
still after 25 hours in status start showing a few x oooooxoooo example...
Can somebody explain why , still after 24-25 hours and oboth same :-(
What Power supply? Are they overclocked? yes oboth to 200gh/s and powersupply 550 watt But all day still ok but after 25 hours i have to restart and again 25 hours ok Umm, They pull 380-400 Watts EACH when overclocked. Do they each have their own power supply? When there is "X" mixed in with the OOOOOO's it generally means there is a power issue or overclock issue. I'm running a Corsair Professional series 860 Watt for 2 overclocked units. Most people run 1000 Watt for 2 overclocked units, but the high end Corsairs can handle the load. |
|
|
|
|
|
|
|
nottm28
|
|
February 21, 2014, 11:22:00 PM |
|
|
donations not accepted
|
|
|
|
InfiniteGrim
|
|
February 21, 2014, 11:28:51 PM |
|
They are pricey, but I believe they are worth it. Plus the 7 year warranty is just amazing!
|
|
|
|
|
PostMixer
Newbie
Offline
Activity: 53
Merit: 0
|
|
February 21, 2014, 11:58:23 PM |
|
Just a heads up that during this last website maintenance, Slush or a representative, posted updates on his Facebook page. Maybe things are turning around in the communications dept. ? "We are experiencing connectivity issues between our US and EU datacentres. Mining is operational, all shares are being counted. We will keep you posted once the connectivity resumes." "Connectivity between US and EU datacenters has been restored, web is now accessible, too. Thank you for your patience." I even got a response to a comment I made on the latest post there.  |
|
|
|
|
Scyntech
Sr. Member
Offline
Activity: 349
Merit: 250
“Blockchain Just Entered The Real World”
|
|
February 22, 2014, 08:10:09 AM |
|
Finally got my 0.01 payout ... yay me
Will be adding 12 - 2.5Gh/s USB miners soon, curious to see how well those do.
|
|
|
|
|
|
shazo
Newbie
Offline
Activity: 23
Merit: 0
|
|
February 22, 2014, 09:12:39 AM |
|
Not sure what was going on with my account. I put my 5 antminer U1's on multipool.us till my account on slush dropped to zero. It took a few hours after I stopped mining on the pool for it to show up that I was no longer mining. I let everything be confirmed so that if it was still having issues with only showing me mining at 2ghash/s I could take everything I have out of slush. I'm now mining back on slush and everything seems to be working again. I'm showing 7934.796 mhash/s on slush and on bfgminer I'm showing 7.98 Gh/s. It took some time for it to build back up on slush but over night it got to around what bfgminer shows. With the cost of bitcoin where it's currently at I'm thinking about buying some coins and getting an S1. If I can still get one for 1.45 coins all it would cost is just over 800 USD.
|
|
|
|
|
denisa
Newbie
Offline
Activity: 12
Merit: 0
|
|
February 22, 2014, 09:49:24 AM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
|
|
|
|
|
|
gourmet
|
|
February 22, 2014, 09:59:07 AM |
|
You are not alone with this problem for this particular block. If you want you may raise a ticket on the Slush support page (see 'knowledge base' link on the left side of the Account Page, you'll need to register for this and then you'll be able to raise a new ticket). Looks like there was some problem on Slush's side, which caused the reward of many people to drop to about 20-25% for this block. When 1369... has problems with his stats, he's apparently already registered. :-) |
|
|
|
|
|
gourmet
|
|
February 22, 2014, 10:32:36 AM |
|
Did this ever happened to you : ""Found block for pool" - that is when it means YOU found it." Must be happy that day "Stratum from pool 0 requested work update" i see that very often, what is it please? May I ask you another question please. At this pace of growing difficulty (+20% every 12 days seems to be exponential) so soon no one will ever mine, so how Bitcoin network will keep on. Deeply thx for your answears Looks like the poster intended to post up to four questions, but I can see only one question-mark here... Are the other sentences intended to be questions also? (an)swears... :-) |
|
|
|
|
anthem
Member
Offline
Activity: 72
Merit: 10
|
|
February 22, 2014, 11:45:43 AM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
Do the math. If two 500 are not good enough then one 950 for two is even worse. Especially if you are over locking. Not sure why you are asking a question to go backwards. |
|
|
|
|
|
kabopar
|
|
February 22, 2014, 11:54:56 AM |
|
You are not alone with this problem for this particular block. If you want you may raise a ticket on the Slush support page (see 'knowledge base' link on the left side of the Account Page, you'll need to register for this and then you'll be able to raise a new ticket). Looks like there was some problem on Slush's side, which caused the reward of many people to drop to about 20-25% for this block. When 1369... has problems with his stats, he's apparently already registered. :-) Gourmet, The support site has a separate login, which differs from the pool login. 1369... If your reward was not fixed, it's likely that you had some issue towards the end of the last block. This is because of Slush's special time-dependent reward system. Cheers |
|
|
|
|
denisa
Newbie
Offline
Activity: 12
Merit: 0
|
|
February 22, 2014, 12:46:48 PM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
Do the math. If two 500 are not good enough then one 950 for two is even worse. Especially if you are over locking. Not sure why you are asking a question to go backwards. Because my two 500 watt psu was really cheap. And 950 psu 80+ much better quality and i saw here on the forum. Somebody running 2 antminer on 850 corsair psu without problems. Thats why !!! |
|
|
|
|
Slesh
Member
Offline
Activity: 103
Merit: 10
|
|
February 22, 2014, 12:51:21 PM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
HI I run 7 S1. - OC to 200. Each on different PSU. I had the same Issue with "xxxx" marks. Biggest help was to flash firmware to new and better cooling (mounted secons fan to the front side of S1 - pulling air out of S1). Now they are without XXXXX. But xxxx doesnt mean they are not working. My S1s were marked as xxxx and still hashing well. But it looks bad So now they run about 41-43 celsius and working well. |
|
|
|
|
|
dlowings
|
|
February 22, 2014, 01:09:53 PM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
HI I run 7 S1. - OC to 200. Each on different PSU. I had the same Issue with "xxxx" marks. Biggest help was to flash firmware to new and better cooling (mounted secons fan to the front side of S1 - pulling air out of S1). Now they are without XXXXX. But xxxx doesnt mean they are not working. My S1s were marked as xxxx and still hashing well. But it looks bad So now they run about 41-43 celsius and working well. Did you do the trick where you flip the blades so the fins face out or did you leave that part stock ? Someone told me flip the blades for better cooling .. |
BTC donations welcome:- 1BrersvQubEKt4m2hBXDNvU1B4RiYe6J4i - Feel free to visit wiki.chainminer.com for free hardware listings, and mining info. - IRC on freenode #wiki.chainminer.com
|
|
|
denisa
Newbie
Offline
Activity: 12
Merit: 0
|
|
February 22, 2014, 01:12:03 PM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
HI I run 7 S1. - OC to 200. Each on different PSU. I had the same Issue with "xxxx" marks. Biggest help was to flash firmware to new and better cooling (mounted secons fan to the front side of S1 - pulling air out of S1). Now they are without XXXXX. But xxxx doesnt mean they are not working. My S1s were marked as xxxx and still hashing well. But it looks bad So now they run about 41-43 celsius and working well. What psu do you have ? Xxx showing to me after 25 hours, i just restart and again runs well just everiday i has to restart.. when i cout HW errors is really small 0,7 % soo just this restarts every day. I am thinking to buy to psu 750 watt |
|
|
|
|
Slesh
Member
Offline
Activity: 103
Merit: 10
|
|
February 22, 2014, 01:19:16 PM |
|
Hi guys i have 2 antminer s1 with 2 500 watt psu but tehy makes me xxxxoxxxoxx i know this psus is too low and cheap for OC . I have in my PC CORSAIR TX 950 watt . What do you think , can one tx950 jandle 2 antminer oc to 200gh/s each ?
Till now i use 500 watt chap psu each for oboth unit.
please answer if better to buy two new stonger psu or just change and connect 2 miners to corsair tx 950 watt
HI I run 7 S1. - OC to 200. Each on different PSU. I had the same Issue with "xxxx" marks. Biggest help was to flash firmware to new and better cooling (mounted secons fan to the front side of S1 - pulling air out of S1). Now they are without XXXXX. But xxxx doesnt mean they are not working. My S1s were marked as xxxx and still hashing well. But it looks bad So now they run about 41-43 celsius and working well. Did you do the trick where you flip the blades so the fins face out or did you leave that part stock ? Someone told me flip the blades for better cooling .. I saw the pictures of this but never try. .. no need to try. Mine hashing well. |
|
|
|
|
|
