sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 07:58:46 AM |
|
i'm getting the same shit at my saturn. disappointing. Both boards are marked with an "1"
here is what bertmod is showing...should i run the enable bin file or update to .96??? it's not bad but 100% for both would be nice but not sure if asking too much.... ASIC slot #1: 45.0 ℃ ASIC slot #2: - ASIC slot #3: - ASIC slot #4: - ASIC slot #5: 40.0 ℃ ASIC slot #6: - Warning: Could not reach cgminer ! ASIC Board Info 0 Temperature sensor: 45.0 C Die ID Cores ON Cores OFF % 0 48 0 100 1 48 0 100 2 48 0 100 3 48 0 100 DC/DC ID ON/OFF Status Input Voltage Output Voltage Output Current 0 ON OK 12 V 0.741 V 40.7 A (30.2 W) 1 No DC/DC detected 2 ON OK 12 V 0.743 V 40.2 A (29.9 W) 3 No DC/DC detected 4 ON OK 12 V 0.759 V 42.3 A (32.1 W) 5 No DC/DC detected 6 No DC/DC detected 7 ON OK 12 V 0.733 V 41.9 A (30.7 W) 4 Temperature sensor: 40.0 C Die ID Cores ON Cores OFF % 0 42 6 87.5 1 47 1 97.9 2 46 2 95.8 3 48 0 100 DC/DC ID ON/OFF Status Input Voltage Output Voltage Output Current 0 ON OK 12 V 0.722 V 34.8 A (25.1 W) 1 No DC/DC detected 2 ON OK 12.1 V 0.754 V 37.9 A (28.6 W) 3 No DC/DC detected 4 ON OK 12.1 V 0.754 V 38.5 A (29 W) 5 No DC/DC detected 6 No DC/DC detected 7 ON OK 12 V 0.735 V 40.6 A (29.8 W) Total DC/DC power output: 235 W I'd give 0.96 or at least EnableCores a try
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
sbfree
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:01:04 AM |
|
login as: root root@192.168.1.135's password: root@Saturn-4CA:~# screen -r cgminer version 3.4.0 - Started: [2013-10-19 06:40:20] -------------------------------------------------------------------------------- (5s):276.6G (avg):251.7Gh/s | A:71424 R:512 HW:14668 WU:3610.2/m ST: 2 SS: 0 NB: 7 LW: 98671 GF: 0 RF: 0 Connected to xxxxxx.57 diff 256 with stratum as user xxxxxminer_knc Block: 000e3164baa403e0... Diff:268M Started: [06:57:52] Best share: 284K -------------------------------------------------------------------------------- [P]ool management ettings [D]isplay options [Q]uit KnC 0: | 260.6G/252.1Gh/s | A:71680 R:512 HW:14685 WU:3615.8/m -------------------------------------------------------------------------------- [2013-10-19 07:05:14] Accepted 00346209 Diff 1.25K/256 KnC 0 [2013-10-19 07:05:15] KnC: core 4-52 was enabled back from disabled state [2013-10-19 07:05:17] Accepted 00332e8c Diff 1.28K/256 KnC 0 [2013-10-19 07:05:19] Accepted 001c8c3d Diff 2.29K/256 KnC 0 [2013-10-19 07:05:24] Accepted 004fbb2e Diff 821/256 KnC 0 [2013-10-19 07:05:30] Accepted 00533492 Diff 787/256 KnC 0 [2013-10-19 07:05:37] Accepted 0005c942 Diff 11.3K/256 KnC 0 [2013-10-19 07:05:49] Accepted 0075de37 Diff 556/256 KnC 0 [2013-10-19 07:05:51] Accepted 007655c4 Diff 553/256 KnC 0 [2013-10-19 07:05:52] Accepted 0056c855 Diff 755/256 KnC 0 [2013-10-19 07:05:53] Accepted 00f6a7c6 Diff 265/256 KnC 0 [2013-10-19 07:05:54] Accepted 00895408 Diff 477/256 KnC 0 here are my saturn stats, on .95 firmware, any input would be greatly appreciated...especially my error rate which I am not sure how to figure out. i'm getting the same shit at my saturn. disappointing. Both boards are marked with an "1" shit ? what's the problem you are minting 251.7 GHs Is not the best I've seen but not the worst either. have u use bertmod aisc_status.pl to get the number of cores enabled on yours asics? if you have a lot of diabled core give 0.96 a try or use http://www.kncminer.com/userfiles/file/enablecores.bin (see support page for instaructions) did you check this if this apply to you http://forum.kncminer.com/filedata/fetch?photoid=8379? sickpig, I am somewhat happy, unit was late in my eyes, and was hoping more for like 275GH/s at the server...i think phoenix1969 has 3 saturns running like that....mine seems to top out at 235/240GH/s on the server side...although less than 1% error rate on the server side...so thanks for the input and will check it out...i did post a bertmod result too. thanks again.
|
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:04:03 AM |
|
sickpig, I am somewhat happy, unit was late in my eyes, and was hoping more for like 275GH/s at the server...i think phoenix1969 has 3 saturns running like that....mine seems to top out at 235/240GH/s on the server side...although less than 1% error rate on the server side...so thanks for the input and will check it out...i did post a bertmod result too. thanks again. you're welcome and let us know your results/imporvements
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:15:38 AM |
|
is there a thread of PSU's hooked up pics?
do we paperclip the PSU directly or plug in the cable and paperclip the end of that?
im a bit dubious regarding the entire affair.
I've applied paper clip at the end of the cable. u can use also a more secure way: http://www.dimastech.it/EN/c/atx-bridge-24-pin-for-power-supply/
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
trepex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:27:13 AM |
|
KnC Cooling & Bertmod temperatures (Saturn miner, 0.95/0.96) Hi, with a closed case my temperatures had been like 48/44C. The die with the hotter temperature often had disabled cores. Opening the case did help a little bit, the perfect setup for me ended to be like this: ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fs23.postimg.org%2F64qx1qgw9%2FKn_C_Sat_airflow.jpg&t=665&c=R97nczAU1I9gfw) Note the additional airflow by the two external fans (ugly setup, I know!). Temperatures down to 41/42C and normally no disabled cores (at 0.96). Room temp. about 20-21C. cgminer stats (20h): (avg):267.1Gh/s | A:4438784 R:72192 HW:218669 WU:3895.2/m (Updated running time, UTC calculation) Even for a Saturn you need additional cooling.trepex
|
|
|
|
idee2013
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:32:31 AM |
|
login as: root root@192.168.1.135's password: root@Saturn-4CA:~# screen -r cgminer version 3.4.0 - Started: [2013-10-19 06:40:20] -------------------------------------------------------------------------------- (5s):276.6G (avg):251.7Gh/s | A:71424 R:512 HW:14668 WU:3610.2/m ST: 2 SS: 0 NB: 7 LW: 98671 GF: 0 RF: 0 Connected to xxxxxx.57 diff 256 with stratum as user xxxxxminer_knc Block: 000e3164baa403e0... Diff:268M Started: [06:57:52] Best share: 284K -------------------------------------------------------------------------------- [P]ool management ettings [D]isplay options [Q]uit KnC 0: | 260.6G/252.1Gh/s | A:71680 R:512 HW:14685 WU:3615.8/m -------------------------------------------------------------------------------- [2013-10-19 07:05:14] Accepted 00346209 Diff 1.25K/256 KnC 0 [2013-10-19 07:05:15] KnC: core 4-52 was enabled back from disabled state [2013-10-19 07:05:17] Accepted 00332e8c Diff 1.28K/256 KnC 0 [2013-10-19 07:05:19] Accepted 001c8c3d Diff 2.29K/256 KnC 0 [2013-10-19 07:05:24] Accepted 004fbb2e Diff 821/256 KnC 0 [2013-10-19 07:05:30] Accepted 00533492 Diff 787/256 KnC 0 [2013-10-19 07:05:37] Accepted 0005c942 Diff 11.3K/256 KnC 0 [2013-10-19 07:05:49] Accepted 0075de37 Diff 556/256 KnC 0 [2013-10-19 07:05:51] Accepted 007655c4 Diff 553/256 KnC 0 [2013-10-19 07:05:52] Accepted 0056c855 Diff 755/256 KnC 0 [2013-10-19 07:05:53] Accepted 00f6a7c6 Diff 265/256 KnC 0 [2013-10-19 07:05:54] Accepted 00895408 Diff 477/256 KnC 0 here are my saturn stats, on .95 firmware, any input would be greatly appreciated...especially my error rate which I am not sure how to figure out. i'm getting the same shit at my saturn. disappointing. Both boards are marked with an "1" shit ? what's the problem you are minting 251.7 GHs Is not the best I've seen but not the worst either. have u use bertmod aisc_status.pl to get the number of cores enabled on yours asics? if you have a lot of diabled core give 0.96 a try or use http://www.kncminer.com/userfiles/file/enablecores.bin (see support page for instaructions) did you check this if this apply to you http://forum.kncminer.com/filedata/fetch?photoid=8379? i know that all. one die has 40% disbaled cores. have tried 4 pools and at pools is mining at 220-230 Gh/s. 250 gh/s avg are in cgminer
|
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:35:35 AM |
|
KnC Cooling & Bertmod temperatures (Saturn miner, 0.95/0.96)
Hi,
with a closed case my temperatures had been like 48/44C. The die with the hotter temperature often had disabled cores. Opening the case did help a little bit, the perfect setup for me ended to be like this:
[img with=100]http://s23.postimg.org/64qx1qgw9/Kn_C_Sat_airflow.jpg[/img]
Note the additional airflow by the two external fans (ugly setup, I know!).
Temperatures down to 41/42C and normally no disabled cores (at 0.96). Room temp. about 20-21C. cgminer stats (22h): (avg):267.1Gh/s | A:4438784 R:72192 HW:218669 WU:3895.2/m
Even for a Saturn you need additional cooling.
trepex
hi trepex thanks for sharing don't be to harsh your own set up is not that ugly anyhow I don't rember where but it seems that improving the airflow in such a wa to have a better cooling of the BB helps the overall perf. somone use a magazine to force the air from the intake to "stay down"... as soon as I get more info I'll let you know. it's a real pity that I have my machine in a colo distant from my home :/
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
sbfree
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:40:12 AM |
|
sickpig, once I install the enablecores bin file, do I need to restart the machine??
|
|
|
|
jelin1984
Legendary
Offline
Activity: 2408
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:40:33 AM |
|
Any news about core off Can make it core on???
|
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:42:06 AM |
|
sickpig, once I install the enablecores bin file, do I need to restart the machine??
it seems so but I didn't try myself since I've my machine hosted in a colo distant from my home and I prefer to do this kind of thing "face to face"
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:44:03 AM |
|
Any news about core off Can make it core on???
hi jelin I won't be able to test it this morning (maybe tomorrow) but it seem that if you have a lot of diabled core 0.96 http://www.kncminer.com/userfiles/file/enablecores.bin (see support page for instaructions) should help.
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
jelin1984
Legendary
Offline
Activity: 2408
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:45:08 AM |
|
I do not have my miner I wait it back from knc
|
|
|
|
sickpig
Legendary
Offline
Activity: 1260
Merit: 1008
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 08:47:27 AM |
|
I do not have my miner I wait it back from knc
rigth you told me. sorry I forgot. I'll let you know as soon as I'm able to apply the new firmware
|
Bitcoin is a participatory system which ought to respect the right of self determinism of all of its users - Gregory Maxwell.
|
|
|
derekleong75
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:00:17 AM |
|
Does disabled cores get re-enabled over time or does it mean that once they are disabled, we will need to install the enablecores.bin to turn them back on again?
|
|
|
|
sbfree
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:02:49 AM |
|
Does disabled cores get re-enabled over time or does it mean that once they are disabled, we will need to install the enablecores.bin to turn them back on again?
i see them get re-enabled, but not sure if this is for all miners, i've heard of some locking and thats when this bin file comes into play.
|
|
|
|
derekleong75
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:04:19 AM |
|
I havent gotten bertmod installed but Im running 0.96. Just hope they get re-enabled. Or some new FW that doesn't disable them when > 10 HW errors. The threshold should be more than 10 IMHO.
|
|
|
|
sbfree
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:04:28 AM |
|
NEED HELP!!
so I updated my saturn to .96 but now get this error....
"Edit file manaully, remember to use proper JSON syntax otherwise the file can not be saved."
{ "pools" : [ { "url" : "xx.xx.xxx.57:3333", "user" : "xxxxxminer_knc", "pass" : "xxx" } ] , "api-listen" : false, "api-network" : false, "api-allow" : "W:0/0" }
not sure what to do with this code...coders help??
|
|
|
|
timmmers
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:13:16 AM |
|
Looking at the rise in the bitcoin exchange rate I cant help but wonder if people are seeing that mining won't break even, or is unaffordable and are buying instead to a greater extent?
|
|
|
|
derekleong75
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:14:27 AM |
|
Looking at the rise in the bitcoin exchange rate I cant help but wonder if people are seeing that mining won't break even, or is unaffordable and are buying instead to a greater extent?
Maybe the miners arent selling. Supply vs demand.
|
|
|
|
derekleong75
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 19, 2013, 09:14:50 AM |
|
NEED HELP!!
so I updated my saturn to .96 but now get this error....
"Edit file manaully, remember to use proper JSON syntax otherwise the file can not be saved."
{ "pools" : [ { "url" : "xx.xx.xxx.57:3333", "user" : "xxxxxminer_knc", "pass" : "xxx" } ] , "api-listen" : false, "api-network" : false, "api-allow" : "W:0/0" }
not sure what to do with this code...coders help??
Use firefox. IE gives me the same error.
|
|
|
|
|