palawan
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 12, 2014, 10:52:13 PM |
|
I got my device and started it up, it ran great for the first day then the hashing dropped by 50%. I looked at miner status and saw that I had the "xxxooo xxooxx" problem. I shut it down, rebooted, problem solved. Eh, not quite, happened again later and within a few days my miner stopped hashing altogether. It was still running but when I tried to check the miner status it logged me out of the webui. I logged back in and the miner status page was blank.
The device responds to ping but when I try a command via webui or ssh it stops responding and typically logs me out. I then have to log in again to complete the action. I'm unable to update firmware, the miner still isn't hashing, and the logs show no errors that I can detect and all services appear to be running.
Has anyone had an issue like this? I've contacted Bitmain support but they have basically been non-responsive other than "we're researching it" whatever that means.
It sounds to me like you have an IP conflict. Another device got assigned the IP address that you assigned to the Ant, and when you connect to the IP address, there's no ssh-server or web-server on that IP address awaiting the connection. Try to see on your router what are the devices connected and if you can, maybe you can disconnect some of the wifi-connected devices (ie tablets/cell phones/laptops).
|
halu
|
|
|
roy7
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 12, 2014, 11:01:08 PM |
|
Should I put a sheet of cardboard or something under the miner so the air from the fan will go all the way through it instead of escaping out the bottom before blowing over the back end of the heatsinks?
|
|
|
|
efarah2549
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 98
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 12, 2014, 11:07:42 PM |
|
Is there a factory reset button?
|
|
|
|
Easy2Mine
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 12, 2014, 11:11:12 PM |
|
Yes, look at the controlerboard. Small button.
|
|
|
|
palawan
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 12, 2014, 11:12:14 PM |
|
|
halu
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 12:15:00 AM |
|
Received 6 Ants today and I can't open the web interface of the 3rd one. I tried resetting it with the button and still nothing ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) The first 2 are running great and I did exactly the same thing with the 3rd one - plug the PCI-E cables + ethernet and then power one. I use a 16 port switch. I started 2 Ants on the same PSU comparing the flashing lights: they were the same. Just the one, which I have already setup with pool details started hashing and the other one cannot be accessed ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) Any ideas?
|
|
|
|
BotwinBG
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 12:22:05 AM |
|
PIC32MX250.hex and antMiner_openwrt20140207.bin . Is it enough flashing antMiner_openwrt20140207.bin ? What is the purpose of PIC32MX250.hex and how/when do you flash it?
Does the cgminer miner included finally support bfgminer proxying ?
|
| AMEPAY | | | | | | ▄▄█████████▄▄ ▄█████████████████▄ ▄█████████████████████▄ ▄█████████▀▀▄▀▀█████████▄ ▄████████▄▄█▀ ▀█▄▄████████▄ ████████ ▀▀█▄██▀▀▄████████ ████████ █ ▄ █ ▄▀▀▄████████ ████████ █ █ █ ▄▀▀▄████████ ▀█████████▄█ █ ▄██████████▀ ▀████████ ▀▀▀ ████████▀ ▀█████████████████████▀ ▀█████████████████▀ ▀▀█████████▀▀ ▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀ | │▌ | AMEPAY IEO
▄██████▄ ▀██████▄ █████████ ▀█████ ███████▀ ▀███ ██████▀ ▄█▄ ▀██ ██████▄ ▀█▀ ▄██ ███████▄ ▄███ █████████ ▄█████ ▀██████▀ ▄██████▀ | |
| │ | | AMEPAY LISTING
▐███▄ ████▌ ▐██████████▄ █████████████ ████▌ █████ ▐████ ▄████ ██████████▀ ▀█████▀▀ | |
| ▐│ | ▄▄█████████▄▄ ▄█████████████████▄ ▄█████████████████████▄ ▄█████████▀▀▄▀▀█████████▄ ▄████████▄▄█▀ ▀█▄▄████████▄ ████████ ▀▀█▄██▀▀▄████████ ████████ █ ▄ █ ▄▀▀▄████████ ████████ █ █ █ ▄▀▀▄████████ ▀█████████▄█ █ ▄██████████▀ ▀████████ ▀▀▀ ████████▀ ▀█████████████████████▀ ▀█████████████████▀ ▀▀█████████▀▀ ▀▀▀▀▀▀▀▀▀▀▀▀▀▀▀ |
|
|
|
Prelude
Legendary
Offline
Activity: 1596
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 01:38:33 AM |
|
More than enough, I run 2 overclocked (400MHz) ants on a single Corsair AX860i.
Curious, are you behind 110v or 230v? Supposedly PSUs 'perform better' with 230v? They're on 240v right now, but it would work on 120v also. 240v makes the PSU a little more efficient and it's a little less hard on the internal components.
|
|
|
|
efarah2549
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 98
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 01:53:00 AM Last edit: February 13, 2014, 10:47:49 PM by efarah2549 |
|
Ive tried reseting everything and running through it again but 192.168.1.99 still brings up nothing. Is there something I need to do to set up my network to access 192.168.1.x I feel like I'm missing an important step which is being glossed over here, can someone please help
EDIT: I solved the problem the issue was conflicting networks trying to search the web, once I disconnected from the internet I was finally able to directly communicate with the device and set it up
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:05:28 AM |
|
Received 6 Ants today and I can't open the web interface of the 3rd one. I tried resetting it with the button and still nothing ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) The first 2 are running great and I did exactly the same thing with the 3rd one - plug the PCI-E cables + ethernet and then power one. I use a 16 port switch. I started 2 Ants on the same PSU comparing the flashing lights: they were the same. Just the one, which I have already setup with pool details started hashing and the other one cannot be accessed ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) Any ideas? Success: miner is now working. I don't know what fixed but exactly, but I reconnected all cables and voilla = it is hashing now.
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:05:55 AM |
|
Ive tried reseting everything and running through it again but 192.168.1.99 still brings up nothing. Is there something I need to do to set up my network to access 192.168.1.x I feel like I'm missing an important step which is being glossed over here, can someone please help
What is your home network? Is the 3rd digit the same as the miner? 192.168. 1.x
|
|
|
|
smithytzu
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:13:14 AM |
|
Can someone help a brother out... This AntMiner is driving me crazy, I've got it setup on my network, logged into the web interface fine, but no matter what mining settings I put on the page, miner status shows nothing! Just says: This section contains no values yetI've gone into the network diagnostics page and I can run both DNS and Pings on Slushs Pool, so it's definitely got a internet connection, rebooted, power on/off, no mining ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) any help? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.themobileitgroup.com.au%2Fminerconfig.png&t=665&c=YB4C1OjBfwcLmg) Is there something I'm missing?
|
BTCCard.com.au - The EFTPOS Bitcoin card for Australia and beyond. Sell some of your BTC for an EFTPOS Card today!
|
|
|
smithytzu
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:23:56 AM |
|
OK, So I plugged my second one in and it's worked straight away. It also seems a bit quieter than my other one, fan it a bit more quiet.
What should I do with my unit from above? factory reset and try again?
|
BTCCard.com.au - The EFTPOS Bitcoin card for Australia and beyond. Sell some of your BTC for an EFTPOS Card today!
|
|
|
palawan
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:25:27 AM |
|
Can someone help a brother out... This AntMiner is driving me crazy, I've got it setup on my network, logged into the web interface fine, but no matter what mining settings I put on the page, miner status shows nothing! Just says: This section contains no values yetI've gone into the network diagnostics page and I can run both DNS and Pings on Slushs Pool, so it's definitely got a internet connection, rebooted, power on/off, no mining ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) any help? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.themobileitgroup.com.au%2Fminerconfig.png&t=665&c=YB4C1OjBfwcLmg) Is there something I'm missing? Is it possible your router is blocking outbound connection to TCP port 3334 or 3333? I know on our work network/wifi, we have a limited set of ports that can go out and I have to use VPN to non-standard TCP/UDP ports. EDIT: nvm as I see your post. factory reset is probably it.
|
halu
|
|
|
Easy2Mine
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:33:48 AM |
|
@ CYPER
I was searching webshops for high end PSU to power the new Ants I ordered from BITMAIN. Every highend PSU with a decent price was sold out. People are buying in mass highend PSU, I never saw high end PSU sold out, not even in the GPU era. Only Enermax Platimax PSU with more than 1200 watt was available. Those Platimax are not worth for those prices. I remember that you highly recommend EVGA Supernova G2 PSU. I never used EVGA before, those Supernova G2 was the only high end that is immediately available. Although I never have heard of Super Flower, the OEM that made EVGA Supernova G2 PSU, I decide to give it a try.
I must say, I don't regret it. The build quality is very good and the red sleeved cables are very sexy. And best of all, the price is FUCKING good compared with other brands.
|
|
|
|
smithytzu
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:40:39 AM |
|
Can someone help a brother out... This AntMiner is driving me crazy, I've got it setup on my network, logged into the web interface fine, but no matter what mining settings I put on the page, miner status shows nothing! Just says: This section contains no values yetI've gone into the network diagnostics page and I can run both DNS and Pings on Slushs Pool, so it's definitely got a internet connection, rebooted, power on/off, no mining ![Sad](https://bitcointalk.org/Smileys/default/sad.gif) any help? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fwww.themobileitgroup.com.au%2Fminerconfig.png&t=665&c=YB4C1OjBfwcLmg) Is there something I'm missing? Is it possible your router is blocking outbound connection to TCP port 3334 or 3333? I know on our work network/wifi, we have a limited set of ports that can go out and I have to use VPN to non-standard TCP/UDP ports. EDIT: nvm as I see your post. factory reset is probably it. Thanks I've now got two running fine, so my first one was definetely a bit of a dud, I'll try the factory reset and see what happens
|
BTCCard.com.au - The EFTPOS Bitcoin card for Australia and beyond. Sell some of your BTC for an EFTPOS Card today!
|
|
|
Xian01
Legendary
Offline
Activity: 1652
Merit: 1067
Christian Antkow
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 02:56:11 AM |
|
My two latest Antminers arrived this evening, and I crapped myself a little bit when the fans didn't spin up automatically on power-up.
Seems the latest batches wait for a certain temperature before spinning up.
|
|
|
|
CYPER
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 03:06:26 AM |
|
@ CYPER
I was searching webshops for high end PSU to power the new Ants I ordered from BITMAIN. Every highend PSU with a decent price was sold out. People are buying in mass highend PSU, I never saw high end PSU sold out, not even in the GPU era. Only Enermax Platimax PSU with more than 1200 watt was available. Those Platimax are not worth for those prices. I remember that you highly recommend EVGA Supernova G2 PSU. I never used EVGA before, those Supernova G2 was the only high end that is immediately available. Although I never have heard of Super Flower, the OEM that made EVGA Supernova G2 PSU, I decide to give it a try.
I must say, I don't regret it. The build quality is very good and the red sleeved cables are very sexy. And best of all, the price is FUCKING good compared with other brands.
I concur ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Best PSU for the money.
|
|
|
|
smithytzu
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 03:08:27 AM |
|
OK so My first Ant appears no good, it's fan is running at max as soon as its turned on and while the interface works fine the miner status never displays anything, could some kind of temperature component be no good and hence why CGminer isn't mining?
Anyone else had the same problem, factory reset seems to do nothing?
|
BTCCard.com.au - The EFTPOS Bitcoin card for Australia and beyond. Sell some of your BTC for an EFTPOS Card today!
|
|
|
minternj
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
February 13, 2014, 03:16:55 AM |
|
Did you make sure all the ribbon cables are connected tightly?
|
|
|
|
|