BITMAIN Antminer S1 support and OverClocking thread

[freebit13]

Yes i changed the first one to x.x.0.101, and its plugged into my router

im connecting now the s1 directly to the pc with ethernet cable, and its ip is x.x.1.99.
i changed the net settings (s1-pc) to x.x.1.x to open s1 ip address with browser, it shows the starting page and then that message

I'd suggest rebooting your pc, it'll sometimes get 'stuck' when changing ip addresses... especially on windows.

[jjj0923]

by the way - I cranked mine up to 420/33 today and was seeing over 215gh/s consistently without error but the temp got up to 47 so I backed it down to 410/34 and it's running about 205 right now - no errors temps 45 and below - fan speed 2,450

no errors.

[lenny_]

by the way - I cranked mine up to 420/33 today and was seeing over 215gh/s consistently without error but the temp got up to 47 so I backed it down to 410/34 and it's running about 205 right now - no errors temps 45 and below - fan speed 2,450

no errors.

Awesome Can you share frequency codes?

[luck5]

Yes i changed the first one to x.x.0.101, and its plugged into my router

im connecting now the s1 directly to the pc with ethernet cable, and its ip is x.x.1.99.
i changed the net settings (s1-pc) to x.x.1.x to open s1 ip address with browser, it shows the starting page and then that message

I'd suggest rebooting your pc, it'll sometimes get 'stuck' when changing ip addresses... especially on windows.

this didnt work, i think something is wrong in the software of the antminer, not in the connection

[mdopro1]

If 1 S1 takes 360W, can I plug 2 of these on a Corsair HX series 850Watt power supply and be ok?

Anyone know values for 360 ?

[thomashrev89]

If 1 S1 takes 360W, can I plug 2 of these on a Corsair HX series 850Watt power supply and be ok?

Anyone know values for 360 ?

Yes you can, but dont overclock them.

What do you mean, vaules for 360?

[loneknives]

I read back page 12 and did some calculating with the formula, one of my miner getting errors at 375mhz and another two was getting errors at 393mhz. I want to get near zero error , so far 1 at 368.75mhz and 2 at 381.25mhz no errors after 1 hour. I was able to get around 187Gh/s and the 2 higher clock around 196Gh/s

here are some hex i calculated using the formula
Hex        mhz
6b89      366.67M
5d05      368.75M
6c09      370.83M
5e05      381.25M
4f01       387.5M

Hope it helps

[mdopro1]

I read back page 12 and did some calculating with the formula, one of my miner getting errors at 375mhz and another two was getting errors at 393mhz. I want to get near zero error , so far 1 at 368.75mhz and 2 at 381.25mhz no errors after 1 hour. I was able to get around 187Gh/s and the 2 higher clock around 196Gh/s

here are some hex i calculated using the formula
Hex        mhz
6b89      366.67M
5d05      368.75M
6c09      370.83M
5e05      381.25M
4f01       387.5M

Hope it helps

That's awesome. Thanks! I'm trying some of these odd values to see where I can relax my ants.

[luck5]

Yes i changed the first one to x.x.0.101, and its plugged into my router

im connecting now the s1 directly to the pc with ethernet cable, and its ip is x.x.1.99.
i changed the net settings (s1-pc) to x.x.1.x to open s1 ip address with browser, it shows the starting page and then that message

I'd suggest rebooting your pc, it'll sometimes get 'stuck' when changing ip addresses... especially on windows.

this didnt work, i think something is wrong in the software of the antminer, not in the connection

Everything's ok after hard reset

[mdopro1]

It's getting a little warm outside and my ants are going up in temps. Most of them are between 41C and 46C "BUT" fans don't seem to spin any faster. Maximum fan speed I've seen is 2040 in the GUI. What gives? Should they be running faster to keep things cool? Is there something I can do other than pulling the blue wire?

[popinjay]

What kind of 24 hour returns is everyone getting right now?  I just set up my S1, overclocked to a frequency of 393, holding steady at 200GH/s and error rate around 0.5%.  The past 24 hours I have mined about 0.01 bitcoin which is about half of what I would expect.  Could it be just a bad run in the pool? Currently at BTCGuild PPLNS.  Any thoughts?  Perhaps I should wait for a full week and see what I get!

[vvhiteknight]

Anyone from the UK recently (past few weeks) ordered an antminer? If so what customs charge did you guys pay? or what value did they put on the shipment?

[jjj0923]

What kind of 24 hour returns is everyone getting right now?  I just set up my S1, overclocked to a frequency of 393, holding steady at 200GH/s and error rate around 0.5%.  The past 24 hours I have mined about 0.01 bitcoin which is about half of what I would expect.  Could it be just a bad run in the pool? Currently at BTCGuild PPLNS.  Any thoughts?  Perhaps I should wait for a full week and see what I get!

through slush's pool I am seeing about .0258 daily and my Average hashrate in last 10 rounds: 189133 Mhash/s

mine has been running for 4.5 day nows

I would say get out of that pool as quickly as possible

I set my payout at .1 and got my first payout in just about 4 days

I'm ordering another S1 on moonday

slush's pool : Pool luck (1 day, 7 days, 30 days):   120%, 120%, 107%

[davida]

can someone tell me if this is normal.  ghash.io tells me i am running at 180ghs, but my hw errors are so high.

http://postimg.org/image/wj6f3r6o9/full

[kefir135]

What kind of 24 hour returns is everyone getting right now?  I just set up my S1, overclocked to a frequency of 393, holding steady at 200GH/s and error rate around 0.5%.  The past 24 hours I have mined about 0.01 bitcoin which is about half of what I would expect.  Could it be just a bad run in the pool? Currently at BTCGuild PPLNS.  Any thoughts?  Perhaps I should wait for a full week and see what I get!

through slush's pool I am seeing about .0258 daily and my Average hashrate in last 10 rounds: 189133 Mhash/s

mine has been running for 4.5 day nows

I would say get out of that pool as quickly as possible

I set my payout at .1 and got my first payout in just about 4 days

I'm ordering another S1 on moonday

slush's pool : Pool luck (1 day, 7 days, 30 days):   120%, 120%, 107%

Do you expect to ever achieve ROI with increasing difficulty ?

 

[jjj0923]

why do you ask?

[jedimstr]

What kind of 24 hour returns is everyone getting right now?  I just set up my S1, overclocked to a frequency of 393, holding steady at 200GH/s and error rate around 0.5%.  The past 24 hours I have mined about 0.01 bitcoin which is about half of what I would expect.  Could it be just a bad run in the pool? Currently at BTCGuild PPLNS.  Any thoughts?  Perhaps I should wait for a full week and see what I get!

through slush's pool I am seeing about .0258 daily and my Average hashrate in last 10 rounds: 189133 Mhash/s

mine has been running for 4.5 day nows

I would say get out of that pool as quickly as possible

I set my payout at .1 and got my first payout in just about 4 days

I'm ordering another S1 on moonday

slush's pool : Pool luck (1 day, 7 days, 30 days):   120%, 120%, 107%

Do you expect to ever achieve ROI with increasing difficulty ?

 

There's always Return On Investment.  It's just a question if it will be negative return, break even, or positive return. I'm assuming you mean positive or break even when you incorrectly use ROI?

[klondike_bar]

I expect to see a positive ROI, as long as difficulty does not go past 20% jumps again, and assuming we see a few more 11-14% jumps in the near future

its just about physically impossible that the amount of hardware in the network will continue to doble every ~1.5months for ever. buyers are running out of funds and mining farms are reaching capacity.

plus, summer is coming.......

[babaji.ca]

plus, summer is coming.......

this means, people will mine less because it will get too hot in the house to sleep at night, or people will find other 'healthier activities' than sitting around refreshing their browsers?

[freebit13]

can someone tell me if this is normal.  ghash.io tells me i am running at 180ghs, but my hw errors are so high.

http://postimg.org/image/wj6f3r6o9/full

It looks to me like your temps might be a bit high and your avg hashrate looks very low. I also think those HW errors are quite high for standard clock speeds, but I'd trust your pool in the end, they know what they are getting and that's what you get paid for. If anything I'd suggest turning it of for a minute and turning it on again, cgminer can get a bit caught up sometimes...