Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[Ale-x1]

Stable for me so far. And has a tiny hashrate increase )
Tested with 10 AMD GPU rig.

[1714845201]

1714845201

[Munka9]

Is anyone else getting the DAG error on 3gb nVidia 1060 cards (or any other 3072MB cards?)

Any fix for not enough vRAM for the DAG or am I better off switching to equihash coins now?

It was fine until I rebooted and I assume a new epoch was reached while I did that.

add the command line -eres 0

Awesome thanks! No hashrate reduction I wonder what it does.

Edit: Neverming it doesnt reserve any future epoch amounts, so one more epoch (2 weeks?) and 3gb cards cant mine anymore?

Switch to Linux and/or put a 4gb card in your primary pcie port. By my maths I'll still be mining on 3gb cards into 2019, at which point I can't help but think all mining is questionable.

[satishchennnupati]

Hi
i recently started mining using Clarymore's Dual. I am only mining ETH as of now.
i keep seeing on screen once in a while:

ETH <date> SHARE FOUND - (GPU 0)
ETH: Share acceoted (250 ms)!

now when i ty to lookup my address on nanopool i keep seeing this message
Account
<my wallet>
not found
Remember: to add your account to the database you should find at least one share

please help as if I am doing something wrong them i am simply exhausting my mining power.

[cryptoillusion1]

Hi
i recently started mining using Clarymore's Dual. I am only mining ETH as of now.
i keep seeing on screen once in a while:

ETH <date> SHARE FOUND - (GPU 0)
ETH: Share acceoted (250 ms)!

now when i ty to lookup my address on nanopool i keep seeing this message
Account
<my wallet>
not found
Remember: to add your account to the database you should find at least one share

please help as if I am doing something wrong them i am simply exhausting my mining power.

How long since you tried this?
Check now and it should be there - If even after one hour it is not there then there is an issue
re-check your wallet address

[igotfits]

latest amd drivers safe to use?

Yes just make sure after install the cards are set to compute

ty kind sweet man, that fixed my issue with unable to OC.

[satishchennnupati]

its running from 2 days. still nothing.

Hi
i recently started mining using Clarymore's Dual. I am only mining ETH as of now.
i keep seeing on screen once in a while:

ETH <date> SHARE FOUND - (GPU 0)
ETH: Share acceoted (250 ms)!

now when i ty to lookup my address on nanopool i keep seeing this message
Account
<my wallet>
not found
Remember: to add your account to the database you should find at least one share

please help as if I am doing something wrong them i am simply exhausting my mining power.

How long since you tried this?
Check now and it should be there - If even after one hour it is not there then there is an issue
re-check your wallet address

[cryptoillusion1]

its running from 2 days. still nothing.

Hi
i recently started mining using Clarymore's Dual. I am only mining ETH as of now.
i keep seeing on screen once in a while:

ETH <date> SHARE FOUND - (GPU 0)
ETH: Share acceoted (250 ms)!

now when i ty to lookup my address on nanopool i keep seeing this message
Account
<my wallet>
not found
Remember: to add your account to the database you should find at least one share

please help as if I am doing something wrong them i am simply exhausting my mining power.

How long since you tried this?
Check now and it should be there - If even after one hour it is not there then there is an issue
re-check your wallet address

can you post your bat file also which version are you using

[satishchennnupati]

This is my bat file

"

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

and I found this in the logs while was trying to gain some insight on what's happening

"23:07:02:504   1e0   watchdog - thread 0 (gpu0), hb time 2734
23:07:02:508   1e0   watchdog - thread 1 (gpu0), hb time 1016
23:07:03:497   3e38   ETH: put share nonce aeb50a38014a8cf8
23:07:03:501   3e38   ETH round found 1 shares
23:07:03:505   4344   ETH: 03/16/18-23:07:03 - SHARE FOUND - (GPU 0)
23:07:03:510   4344   send: {"id":10,"method":"eth_submitWork","params":["0xaeb50a38014a8cf8","0x98bd38500076ce467e3f8792bb54df7452fe408c7a7f947b46b6ce8a99753788","0x4e0abf8513087c241fad4701cafc18baa839e21c8e44917cf5e75d9ad634003f"]}
"

now my bigger question why does it has some other wallet addresses in the last line of the log.
I am using Claymore's dual miner version 10.5

please help, this is frustrating. I am watching from 3 days for my address to appear on nanopool.

its running from 2 days. still nothing.

Hi
i recently started mining using Clarymore's Dual. I am only mining ETH as of now.
i keep seeing on screen once in a while:

ETH <date> SHARE FOUND - (GPU 0)
ETH: Share acceoted (250 ms)!

now when i ty to lookup my address on nanopool i keep seeing this message
Account
<my wallet>
not found
Remember: to add your account to the database you should find at least one share

please help as if I am doing something wrong them i am simply exhausting my mining power.

How long since you tried this?
Check now and it should be there - If even after one hour it is not there then there is an issue
re-check your wallet address

can you post your bat file also which version are you using

[big al]

Your wallet will only be in the log a couple of times at the top.  It should literally take minutes for them to make a page.

[Spill]

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

Ok i'll bite you're not mining at nanopool you're mining at ethermine.   If you really want to mine at nanopool change your bat file
to where i have it boldfaced.
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

[satishchennnupati]

oho my Rutherford.... what the hell i was doing. OK even though i was mining on etherminer should my wallet be visible there ?

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

Ok i'll bite you're not mining at nanopool you're mining at ethermine.   If you really want to mine at nanopool change your bat file
to where i have it boldfaced.
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

[cryptoillusion1]

oho my Rutherford.... what the hell i was doing. OK even though i was mining on etherminer should my wallet be visible there ?

setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

Ok i'll bite you're not mining at nanopool you're mining at ethermine.   If you really want to mine at nanopool change your bat file
to where i have it boldfaced.
start C:\GPU_Miner_v10.5\EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal 0xB529d2FaC7dA5902Cba304dA4901315A82668332.Vismai -epsw x
pause"

see https://ethermine.org/miners/0xB529d2FaC7dA5902Cba304dA4901315A82668332
I can see you have a balance of 0.00052 ETH

[dth122]

I'm having a problem with a crash or lockup when starting.  I've tried 11.3, 11.4 and 11.5.  All exhibit the same issue.

Claymore runs great when I don't set any GPU parameters in the config file.  However, as soon as I add any clock or voltage adjustments to the GPUs, one of 3 things happens when I start the software:
1. BSOD with Thread Stuck in Device Driver error
2. System just locks up (no mouse movement or num lock), requiring a hard power cycle
3. It starts properly but eventually exhibits failure 1 or 2 after an hour or two.

When I say the problem happens with any GPU parameters, I've tested this by using all stock settings (the same that the GPUs default to when I don't set anything in the config), but I still have the problem.  So, the problem is not settings outside of a stable operating range.

The crashes usually occur after "POOL/SOLO Version", but not all the time.

I checked the logs but nothing stands out.  The logs look normal then just stop when the crash happens. 

I'm running a rig with 3xRX570 and 3xRX580 using the blockchain driver on Win10.

I've tried running -oldkernels 1, but that actually made it worse.  I couldn't start mining at all.  I always get OpenCL errors, even with no clock or voltage adjustments.

I tried -gser1 and -gser 2, but neither of those helped.

Is there something else I should be looking at?
 - Dave

[leonix007]

I'm having a problem with a crash or lockup when starting.  I've tried 11.3, 11.4 and 11.5.  All exhibit the same issue.

Claymore runs great when I don't set any GPU parameters in the config file.  However, as soon as I add any clock or voltage adjustments to the GPUs, one of 3 things happens when I start the software:
1. BSOD with Thread Stuck in Device Driver error
2. System just locks up (no mouse movement or num lock), requiring a hard power cycle
3. It starts properly but eventually exhibits failure 1 or 2 after an hour or two.

When I say the problem happens with any GPU parameters, I've tested this by using all stock settings (the same that the GPUs default to when I don't set anything in the config), but I still have the problem.  So, the problem is not settings outside of a stable operating range.

The crashes usually occur after "POOL/SOLO Version", but not all the time.

I checked the logs but nothing stands out.  The logs look normal then just stop when the crash happens. 

I'm running a rig with 3xRX570 and 3xRX580 using the blockchain driver on Win10.

I've tried running -oldkernels 1, but that actually made it worse.  I couldn't start mining at all.  I always get OpenCL errors, even with no clock or voltage adjustments.

I tried -gser1 and -gser 2, but neither of those helped.

Is there something else I should be looking at?
 - Dave

Start at mining only one GPU installed in PCIe x16 slot, and set aside or exclude all other GPU's for the meantime.

If this runs successfully,  you may now install other GPU's one by one, from there you can actually troubleshoot which might be the culprits.

It maybe a Riser, PSU, Drivers, etc.

[dth122]

Start at mining only one GPU installed in PCIe x16 slot, and set aside or exclude all other GPU's for the meantime.

If this runs successfully,  you may now install other GPU's one by one, from there you can actually troubleshoot which might be the culprits.

It maybe a Riser, PSU, Drivers, etc.

I can try that, but what will I learn?  The system runs stable for 24+ hours if I don't modify the GPU settings or if I modify the settings using Afterburner.  But putting those same settings in the Claymore config causes a crash on startup. 

Doesn't the fact that I can run stable with no GPU modifiers (or modifying GPU with Afterburner) indicate that hardware and drivers are working correctly?
 - Dave

[Poweriser]

Dear Claymore, do you plan to add new algorithms to the next version of the program? Smart coin, it seems that died, on other coins the difficulty is high. What about Keccakc?

The miner is

Claymore's Dual Ethereum + Decred/Siacoin/Lbry/Pascal/Blake2s/Keccak AMD+NVIDIA GPU Miner.

Keccak is not Keccakc

[midgey]

If you haven't already goto mining.help has a complete description and software tools that help you set up claymores for max performance including a 1 click bios upgrade which worked brilliantly for me.

[midgey]

mining.help also has a pretty good description of how to control individual card settings and claymores control in his opinion isn't stable.

[ozitr06]

https://forum.ethereum.org/discussion/14274/gpuminer-cu-k1-failed-4-unspecified-launch-failure

help pls .s

[Ursul0]

I'm having a problem with a crash or lockup when starting.  I've tried 11.3, 11.4 and 11.5.  All exhibit the same issue.

Claymore runs great when I don't set any GPU parameters in the config file.  However, as soon as I add any clock or voltage adjustments to the GPUs, one of 3 things happens when I start the software:
1. BSOD with Thread Stuck in Device Driver error
2. System just locks up (no mouse movement or num lock), requiring a hard power cycle
3. It starts properly but eventually exhibits failure 1 or 2 after an hour or two.

When I say the problem happens with any GPU parameters, I've tested this by using all stock settings (the same that the GPUs default to when I don't set anything in the config), but I still have the problem.  So, the problem is not settings outside of a stable operating range.

The crashes usually occur after "POOL/SOLO Version", but not all the time.

I checked the logs but nothing stands out.  The logs look normal then just stop when the crash happens. 

I'm running a rig with 3xRX570 and 3xRX580 using the blockchain driver on Win10.

I've tried running -oldkernels 1, but that actually made it worse.  I couldn't start mining at all.  I always get OpenCL errors, even with no clock or voltage adjustments.

I tried -gser1 and -gser 2, but neither of those helped.

Is there something else I should be looking at?
 - Dave

Start at mining only one GPU installed in PCIe x16 slot, and set aside or exclude all other GPU's for the meantime.

If this runs successfully,  you may now install other GPU's one by one, from there you can actually troubleshoot which might be the culprits.

It maybe a Riser, PSU, Drivers, etc.

I was posting a while back that I've got stability issues on mixed polaris 570&580 rigs.
Somehow similarly I have one miner with 8*570*4GB Asus (boxy looking and not the Strix one) and 4*580*8GB Nitros
It was just giving me pain - miner was crashing probably every few hours (the only one out of  10+ of the similar build, except the mixed 570&580)
In some logs I could see that GPU0 (my display card) would fail so...I had a display dummy also mem (I think Elpida) set at 1920
So I rolled back to 11.2 removed the display dummy and increased the mem clock to 1950 and now it's fine.