Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[Vann]

Sounds like the miner command prompt window is freezing. It's a known bug. Follow the steps in the README.txt

- Miner freezes if I put cursor to its window in Windows 10 until any key is pressed. Sometimes miner freezes randomly until any key is pressed.
  You should make some changes in Windows:
  https://superuser.com/questions/555160/windows-command-prompt-freezing-on-focus
  https://superuser.com/questions/419717/windows-command-prompt-freezing-randomly?rq=1
  https://superuser.com/questions/1051821/command-prompt-random-pause?rq=1

[SKBitCoinX]

Anyone having issues with Miner restart or freeze on DEV FEE with load of the DAG?

tried a few things, whats everyone using in their config for AMD RX cards

I haven't got a crash or miner restart yet from the DAG on DEV FEE running the below config
I tried a couple different options on ETH mining mode only to start, just for troubleshooting.

weird thing is I haven't seen the DEV FEE, dev mining start show up on screen yet.. not sure if thats in the backgroudn from the options im rumming in config now but anyone have some feedback let me know.

you will see the lines with # that i have turned OFF for now as i was trying different things.... -allpools 1 -allcoins -1 -allcoins 1  would always cause miner restart after DAG on DEV FEE...

-epool stratum+tcp://lb.geo.pirlpool.eu:8002
-ewal MYWalletAddress
-epsw x
-eworker RX-Miner
#-allpools 1
-allcoins etc
#-allcoins exp
#-allcoins -1
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal
#-dpsw x
-esm 0
#-mode 0
#-gser 2
#-ethi 10
-etha 0
-asm 1
-mode 1
-fanmin 50
-tstop 85
-mport 0
-r 0

Has anyone experienced hashrate drop in what seems to be a quite consistent matter?
I'm not talking about my rock solid RX570 rigs, they've been absolute beasts for a year now. But I'm struggling with the Vega rig.

All GPUs will hash at ~41MH/s until one decides to drop to 26 for a minute. Then goes back up to 41. This happens regularly.

Surely if it were temp throttling (which seems unlikely as I have the fans running at pretty much 100%) the hashrate reduction would be more gradual... and not bam!... down to 26?

Any clues? I'm on v11.4, latest Adrenalin, Vega56@64, safe softPP table with specific clocks and voltages set in Claymore miner.

Got the same issue but with my rx580 rig, all 7 cards running stable at 31 mh/s. From time to time gpu0 suddenly crashes to a rate around 5-10 mh/s and after a few minutes hits back to 31. There are no error logs showing up, also no incorrect shares and temps are fine. Card has also the same setup as other cards (no oc), kinda strange since it just appeared lately, running currently v 11.5

same issue here
are you using stock rom  with no oc?

In addition to the above, Mr Claymore, your miner reboots my rig every hour. Almost without fail. There's no error in the log, no watchdog issue with GPUs OpenCL issues, nothing. I'm baffled.

1. Unstable speed - I see this issue sometimes on different cards, but I have no idea about the reason - miner executes jobs on GPUs in the same way all the time, but sometimes GPU becomes slower for some time. I noticed that often different "-ethi" value helps, try "-ethi 4" or "-ethi 12" and see if it helps. I think that it must be something related to AMD drivers but I cannot confirm it yet.
2. I have a few rigs on v11.5 and they are working for days until I restart miner to perform some new tests, but I always use non-overclocked cards and default bioses, I have to do it to exclude everything except miner in case of any problems. When you use miner on overclocked/unstable rig you cannot be sure that the reason of the problems is the miner, but of course you will blame it Try to reduce "-ethi" value, if it does not help you can use the version that works fine for you.

[big al]

Hi all,

Does anyone knows how to reduce stale shares? Currently I have 10-15% stale shares mining ETH but no invalid shares.

Any help would be appreciated.

Thanks

What pool?  The faster the pool solves blocks the more likely you will have stales.  Also if the pool difficulty is set too high that will cause stales.  But too low causes a lot of traffic.  Also remember the higher the difficulty the more you are losing on stales because larger shares are worth more.

I'm on anorak which has 3 different levels of difficulty.

I am on Ethermine and solo mine ETH. Should I try other pools?

Yes come try anorak.

[dragonmike]

Has anyone experienced hashrate drop in what seems to be a quite consistent matter?
I'm not talking about my rock solid RX570 rigs, they've been absolute beasts for a year now. But I'm struggling with the Vega rig.

All GPUs will hash at ~41MH/s until one decides to drop to 26 for a minute. Then goes back up to 41. This happens regularly.

Surely if it were temp throttling (which seems unlikely as I have the fans running at pretty much 100%) the hashrate reduction would be more gradual... and not bam!... down to 26?

Any clues? I'm on v11.4, latest Adrenalin, Vega56@64, safe softPP table with specific clocks and voltages set in Claymore miner.

Got the same issue but with my rx580 rig, all 7 cards running stable at 31 mh/s. From time to time gpu0 suddenly crashes to a rate around 5-10 mh/s and after a few minutes hits back to 31. There are no error logs showing up, also no incorrect shares and temps are fine. Card has also the same setup as other cards (no oc), kinda strange since it just appeared lately, running currently v 11.5

same issue here
are you using stock rom  with no oc?

In addition to the above, Mr Claymore, your miner reboots my rig every hour. Almost without fail. There's no error in the log, no watchdog issue with GPUs OpenCL issues, nothing. I'm baffled.

1. Unstable speed - I see this issue sometimes on different cards, but I have no idea about the reason - miner executes jobs on GPUs in the same way all the time, but sometimes GPU becomes slower for some time. I noticed that often different "-ethi" value helps, try "-ethi 4" or "-ethi 12" and see if it helps. I think that it must be something related to AMD drivers but I cannot confirm it yet.
2. I have a few rigs on v11.5 and they are working for days until I restart miner to perform some new tests, but I always use non-overclocked cards and default bioses, I have to do it to exclude everything except miner in case of any problems. When you use miner on overclocked/unstable rig you cannot be sure that the reason of the problems is the miner, but of course you will blame it Try to reduce "-ethi" value, if it does not help you can use the version that works fine for you.

Of course we blame the miner!
Ok I'll try to spend some time troubleshooting and investigating the hash drop. This isn't my first rig using your miner, as said, I've got plenty of RX 570's that have been chugging along (once for over two months without restarting) so I do know a thing or two about stability.

However, I think the hourly restarts I'm getting with the Vega rig are completely unrelated. That's just too coincidental. Very weird. As said, no error, the log just stops in the middle of what it was doing.

[pogsnet]

v11.1 is much stable than v11.0 which i found more stable than v11.5


So I suggest v11.1 for those who experience a lot of instability.

[MinerosYV]

Is it just me or NLpool is not working?

[janding]

Is there a benefit to using the new ethermine ssl connection?
i.e lower fee? better shares?

The answer is NO to any of those reasons you asked.
However, you open yourself up to be hacked/attacked at the internet backbone level and have all your
shares go to someone else if you don't use the SSL connection.

So, IMO it's ridiculous to not use it.

 

[kyoshiro0911]

btw, this miner just keeps blowing my mind. i put decred intensity to 50% and it made my eth hashrate better lol from 63 to 64 and decred from 900 to 1600.

as for my R9 290 issue. it's still happening. the gpu clock just wont stay where i put it with msi afterburner. it starts out that way but then as the card gets hotter the gpu core clock will go down to 820ish. i think i will try underclocking it to 800mh/s see if it's stable.. any other ideas? thx 

[Mashy81]

btw, this miner just keeps blowing my mind. i put decred intensity to 50% and it made my eth hashrate better lol from 63 to 64 and decred from 900 to 1600.

as for my R9 290 issue. it's still happening. the gpu clock just wont stay where i put it with msi afterburner. it starts out that way but then as the card gets hotter the gpu core clock will go down to 820ish. i think i will try underclocking it to 800mh/s see if it's stable.. any other ideas? thx 

I just noticed something similar. I get 30.3mhs eth only mining. Dual mining with xvg I get and increase to 31.4mhs  on rx 570s. Dcri at 45

[skablast]

Is it just me or NLpool is not working?

its you probably.

I have 4 rigs there and in termo of XVG , results are in line with WTM.

[angelesmix]

btw, this miner just keeps blowing my mind. i put decred intensity to 50% and it made my eth hashrate better lol from 63 to 64 and decred from 900 to 1600.

as for my R9 290 issue. it's still happening. the gpu clock just wont stay where i put it with msi afterburner. it starts out that way but then as the card gets hotter the gpu core clock will go down to 820ish. i think i will try underclocking it to 800mh/s see if it's stable.. any other ideas? thx 

I just noticed something similar. I get 30.3mhs eth only mining. Dual mining with xvg I get and increase to 31.4mhs  on rx 570s. Dcri at 45

your memory ? rx 570

[derselben]

Hello to everyone!

Few days ago my 1060 3gb stoped mining ETH due to this:

Code:

CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
CUDA error - cannot allocate big buffer for DAG. Check readme.txt for possible solutions.
GPU 6 failed
Setting DAG epoch #176 for GPU6
GPU 6, CUDA error 11 - cannot write buffer for DAG
GPU 4 failed
Setting DAG epoch #176 for GPU4
GPU 4, CUDA error 11 - cannot write buffer for DAG
Setting DAG epoch #176 for GPU2
GPU 2 failed
Setting DAG epoch #176 for GPU3
GPU 3 failed
GPU 2, CUDA error 11 - cannot write buffer for DAG
GPU 5 failed
Setting DAG epoch #176 for GPU5
GPU 1 failed
Setting DAG epoch #176 for GPU1
GPU 3, CUDA error 11 - cannot write buffer for DAG
GPU 5, CUDA error 11 - cannot write buffer for DAG
GPU 1, CUDA error 11 - cannot write buffer for DAG
GPU 6 failed
GPU 4 failed
GPU 2 failed
GPU 3 failed
GPU 1 failed
GPU 5 failed

I've started to workaround on this.
I've tried to mine musicoin and it was working good, then I changed my epools file and pushed 'r' to switch back to ETH, and wow! dag file for ETH was created succesfully and minnig was started.

But it is not very useful solution for this, is there any settings to resolve this in a proper way?

my config file is:

Code:

-r 1
-retrydelay 5
-mport 0
-dcri 20
-altnum 1
-dcoin sia
-mode 1
-dbg -1
-allcoins 1

here is my output where I'm switching to ETH from MUSIC:

Code:

Total cards: 6
ETH: Stratum - connecting to 'musicoin.miningclub.info' <137.74.172.54> port 8558 (unsecure)
ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)
ETH: eth-proxy stratum mode
"-allcoins" option is set, default pools will be used for devfee, check "Readme" file for details.
Watchdog enabled

ETH: Stratum - Connected (musicoin.miningclub.info:8558) (unsecure)
ETH: Authorized
Setting DAG epoch #73...
Setting DAG epoch #73 for GPU5
Setting DAG epoch #73 for GPU4
Setting DAG epoch #73 for GPU1
Setting DAG epoch #73 for GPU3
Setting DAG epoch #73 for GPU2
Setting DAG epoch #73 for GPU6
Create GPU buffer for GPU5
Create GPU buffer for GPU4
Create GPU buffer for GPU1
Create GPU buffer for GPU3
Create GPU buffer for GPU2
Create GPU buffer for GPU6
GPU5 DAG creation time - 6470 ms
Setting DAG epoch #73 for GPU5 done
GPU3 DAG creation time - 6462 ms
Setting DAG epoch #73 for GPU3 done
GPU4 DAG creation time - 6497 ms
Setting DAG epoch #73 for GPU4 done
GPU2 DAG creation time - 6562 ms
Setting DAG epoch #73 for GPU2 done
GPU6 DAG creation time - 6599 ms
Setting DAG epoch #73 for GPU6 done
GPU1 DAG creation time - 6922 ms
Setting DAG epoch #73 for GPU1 done
ETH: 03/23/18-14:16:45 - New job from musicoin.miningclub.info:8558
ETH - Total Speed: 140.872 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU1 20.299 Mh/s, GPU2 24.086 Mh/s, GPU3 24.145 Mh/s, GPU4 24.134 Mh/s, GPU5 24.103 Mh/s, GPU6 24.106 Mh/s
ETH: 03/23/18-14:16:45 - SHARE FOUND - (GPU 4)
ETH: Share accepted (78 ms)!
ETH: 03/23/18-14:16:55 - New job from musicoin.miningclub.info:8558
ETH - Total Speed: 140.797 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
ETH: GPU1 20.293 Mh/s, GPU2 24.111 Mh/s, GPU3 24.109 Mh/s, GPU4 24.111 Mh/s, GPU5 24.106 Mh/s, GPU6 24.068 Mh/s
GPU1 t=63C fan=69%, GPU2 t=61C fan=66%, GPU3 t=62C fan=68%, GPU4 t=67C fan=75%, GPU5 t=64C fan=71%, GPU6 t=58C fan=62%
ETH: 03/23/18-14:17:02 - New job from musicoin.miningclub.info:8558
ETH - Total Speed: 144.669 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
ETH: GPU1 24.063 Mh/s, GPU2 24.125 Mh/s, GPU3 24.103 Mh/s, GPU4 24.123 Mh/s, GPU5 24.127 Mh/s, GPU6 24.127 Mh/s
ETH: 03/23/18-14:17:04 - New job from musicoin.miningclub.info:8558
ETH - Total Speed: 144.751 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
ETH: GPU1 24.078 Mh/s, GPU2 24.124 Mh/s, GPU3 24.159 Mh/s, GPU4 24.143 Mh/s, GPU5 24.114 Mh/s, GPU6 24.133 Mh/s
Reloading epools.txt
ETH: 2 pools are specified
Main Ethereum pool is eth-eu2.nanopool.org:9999
ETH: Stratum - connecting to 'eth-eu2.nanopool.org' <149.202.42.174> port 9999 (unsecure)
ETH: Stratum - Connected (eth-eu2.nanopool.org:9999) (unsecure)
ETH: Authorized
Setting DAG epoch #176...
Setting DAG epoch #176 for GPU1
Setting DAG epoch #176 for GPU4
Setting DAG epoch #176 for GPU6
Create GPU buffer for GPU4
Setting DAG epoch #176 for GPU2
Create GPU buffer for GPU2
Create GPU buffer for GPU1
Setting DAG epoch #176 for GPU5
Create GPU buffer for GPU5
Setting DAG epoch #176 for GPU3
Create GPU buffer for GPU3
Create GPU buffer for GPU6
ETH: 03/23/18-14:17:16 - New job from eth-eu2.nanopool.org:9999
ETH - Total Speed: 0.000 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
ETH: GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s, GPU5 0.000 Mh/s, GPU6 0.000 Mh/s
GPU3 DAG creation time - 9874 ms
Setting DAG epoch #176 for GPU3 done
GPU4 DAG creation time - 9894 ms
Setting DAG epoch #176 for GPU4 done
GPU5 DAG creation time - 9897 ms
Setting DAG epoch #176 for GPU5 done
GPU2 DAG creation time - 10014 ms
Setting DAG epoch #176 for GPU2 done
ETH: 03/23/18-14:17:20 - New job from eth-eu2.nanopool.org:9999
ETH - Total Speed: 96.260 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
GPU6 DAG creation time - 10132 ms
ETH: GPU1 0.000 Mh/s, GPU2 24.110 Mh/s, GPU3 24.043 Mh/s, GPU4 24.063 Mh/s, GPU5 24.044 Mh/s, GPU6 0.000 Mh/s
Setting DAG epoch #176 for GPU6 done
GPU1 DAG creation time - 10795 ms
Setting DAG epoch #176 for GPU1 done
ETH: 03/23/18-14:17:24 - New job from eth-eu2.nanopool.org:9999
ETH - Total Speed: 144.359 Mh/s, Total Shares: 1, Rejected: 0, Time: 00:00
ETH: GPU1 24.027 Mh/s, GPU2 24.027 Mh/s, GPU3 24.024 Mh/s, GPU4 24.104 Mh/s, GPU5 24.104 Mh/s, GPU6 24.073 Mh/s

[angelesmix]

1060 3gb -- Bye bye

[RooiWillie]

Few days ago my 1060 3gb stoped mining ETH due to this...

Sadly there is not much to be done here. You have 3 options:
1. Keep up with this method until it does not work anymore
2. Mine something else
3. Set up your rig with Linux. Source: https://www.youtube.com/watch?v=QPaee47TCZc

[Mashy81]

btw, this miner just keeps blowing my mind. i put decred intensity to 50% and it made my eth hashrate better lol from 63 to 64 and decred from 900 to 1600.

as for my R9 290 issue. it's still happening. the gpu clock just wont stay where i put it with msi afterburner. it starts out that way but then as the card gets hotter the gpu core clock will go down to 820ish. i think i will try underclocking it to 800mh/s see if it's stable.. any other ideas? thx 

I just noticed something similar. I get 30.3mhs eth only mining. Dual mining with xvg I get and increase to 31.4mhs  on rx 570s. Dcri at 45

your memory ? rx 570

Gigabyte 4G gaming with samsung memory

[ermis1975]

I have a 1050 ti and I want to install more cards, but not NVIDIA, RX570. How can I do it in w10? Connect the AMD card and after install drivers for mining? Also in Claymore I have to make some changes? Thanks.

[playfast]

The DAG epoch for musicoin changed from #72 to #73. It's getting bigger, online dag calculator says 2gb cards will only work on MUSIC until December.

[woodaxe]

Managed to squeeze 47.9mhs from my vega56 on 11.5

how did you manage that and what wattage is that pulling at the wall

thanks in advance

[alizali]

i try to use -cvddc option in start.bat file to allocate 825mV to my rx470
the core voltage in bios is dynamic
but it does not work and with the option in start.bat file still GPU-Z show 1000mV
on the wall same
i have to use a program such as sapphire trixx to undervolt each card for -175mV

[komodorowiec]

Was anybody able to run Claymore 11.5 (or higher then v10) on 280x or 7970 cards? I'm trying for a week and no progres. I used ubuntu 16.04 server (desktop too) 4 or 8GB of ram, z270a and H110 chipset nothing helps (Amd drivers 17,50). When I switch to the 10.6 claymore everything works on the same machine on the same system.

When i run Claymore 11.5 the DAG file i not loading. Or it's loading for couple of minutes. Most of the times when miner starts I can see brake in ping responses from the rig. SSH hangs for a second or two and then connection is going back on and I can see something like that:


ETH: Authorized
Setting DAG epoch #175...
Setting DAG epoch #175 for GPU4
Create GPU buffer for GPU4
Setting DAG epoch #175 for GPU3
Setting DAG epoch #175 for GPU1
Setting DAG epoch #175 for GPU2
Create GPU buffer for GPU2
Setting DAG epoch #175 for GPU0
Create GPU buffer for GPU0
Create GPU buffer for GPU1
Create GPU buffer for GPU3
GPU0 t=43C fan=33%, GPU1 t=37C fan=33%, GPU2 t=39C fan=33%, GPU3 t=46C fan=33%, GPU4 t=47C fan=33%
ETH: 03/15/18-15:04:33 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s
ETH: 03/15/18-15:04:33 - New job from eth-eu1.nanopool.org:9999
ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
ETH: GPU0 0.000 Mh/s, GPU1 0.000 Mh/s, GPU2 0.000 Mh/s, GPU3 0.000 Mh/s, GPU4 0.000 Mh/s


Alaways 0.000 Mh/s. Then the Claymore restarts it self and so on. I tryed -ethi  -oldkernels -asm -lidag -gser. Nothing helps. Too add my rig was powered by dell dps1200W server psu and now it's powered by 2880W server psu, rig consumes about 1100W.

Please help me.