Re: [ANN] Technobit HEX16A2 - 24 Ghs - 50 EUR 48 h shippment

[Jeffrey]

I hope it comes molex.  I am not positive which wires to strip.

I ordered 2 (2 different dates though)
One came with molex, other came without.
If you have to strip, get a yellow and black. Yellow is +12v, black is GND. You can just cut off any molex connector, strip yellow and black to connect, and tape the red and other black to make sure they don't touch anything.

[Jeffrey]

When I click the start button, a red/orange led on the hex16a2 starts burning, the "work age" starts running, but no hashing occurs.
It's connected to a Corsair 430 watt PSU (30A on 12v) with nothing else attached to it, so that should be OK. (and yes, PSU is running by connecting the green and a black wire on the 24p plug)
I've tried 2 different USB cables, both didn't work.
The user on BTC guild works, I'm using the same (but with _1, this one is _2) for my AntMiner and it works fine.

I'm just confused about the proxy window, it shows all kinds of errors but they don't really make sense to me.... help help please

[Zich]

When I click the start button, a red/orange led on the hex16a2 starts burning, the "work age" starts running, but no hashing occurs.
It's connected to a Corsair 430 watt PSU (30A on 12v) with nothing else attached to it, so that should be OK. (and yes, PSU is running by connecting the green and a black wire on the 24p plug)
I've tried 2 different USB cables, both didn't work.
The user on BTC guild works, I'm using the same (but with _1, this one is _2) for my AntMiner and it works fine.

I'm just confused about the proxy window, it shows all kinds of errors but they don't really make sense to me.... help help please

Try uncheck bitfury option

[Jeffrey]

Try uncheck bitfury option

Nope, didn't work. Shut down hexminer, disconnected the miner from both the psu and usb (to make sure it's reset)
Started hexminer, connected the miner and picked the comport, disabled the bitfury check, but same behavior. Work age starts running, speed and all others stay 00000

[btmtb]

When I click the start button, a red/orange led on the hex16a2 starts burning, the "work age" starts running, but no hashing occurs.
It's connected to a Corsair 430 watt PSU (30A on 12v) with nothing else attached to it, so that should be OK. (and yes, PSU is running by connecting the green and a black wire on the 24p plug)
I've tried 2 different USB cables, both didn't work.
The user on BTC guild works, I'm using the same (but with _1, this one is _2) for my AntMiner and it works fine.

I'm just confused about the proxy window, it shows all kinds of errors but they don't really make sense to me.... help help please

Firstly, check the technobits download page for 1.0.0.3, and then have a look at your settings. I'm on Slush's Pooling (mining.cz) which is the proxy default, conveniently enough. For ref, these are my settings, from a bit of trial of error, it does run hot (62deg C at chip if running stock) but fantastically stable, but I've added extra heatsinks and a quieter fan. I'd be interested to see what settings everyone else is running with too, see if we can refine down to a good working set:


I would really much rather have a working patch for/integration with CGMiner under windows than use HexMiner and the stratum proxy... anyone know if this is even on the cards?

[btmtb]

Merry Christmas, Merry Christmas, Ho Ho Ho. I hope all of you enjoy this holiday  

While waiting for my HEX16A2, i make power connector for the miner which will get power from EPS 12V connector from PSU.
I use EPS 12 V because my PSU not fully modular & come with 2X EPS 12V connector, so waste to not use them


Seasonic M12II Bronze 620W                                            Buy cheap ATX 20 to 24 pin converter on ebay to make the connector

Your leads look fantastic, like they were good fun to make. I was going to say you're missing some heatshrink tubing but I spotted it in your bottom pictures, and I can't rave about it enough. Get those solder joints insulated everyone, you can get mixed packs of the stuff from amazon and ebay dirt cheap, and it shrinks tight with the heat of a soldering iron perfectly.

I'm curious about why so many people are getting dedicated PSU's for a single board? Is there any particular reason you didn't want to just get an extended molex lead and run it from your PC psu, that is (presumably) a good one, already purchased, and on most of the time anyway?

[Zich]

Your leads look fantastic, like they were good fun to make. I was going to say you're missing some heatshrink tubing but I spotted it in your bottom pictures, and I can't rave about it enough. Get those solder joints insulated everyone, you can get mixed packs of the stuff from amazon and ebay dirt cheap, and it shrinks tight with the heat of a soldering iron perfectly.

I'm curious about why so many people are getting dedicated PSU's for a single board? Is there any particular reason you didn't want to just get an extended molex lead and run it from your PC psu, that is (presumably) a good one, already purchased, and on most of the time anyway?

Actually the miner run on TPLINK TL-MR3020 in my bedroom which had air conditioner while my PC on my shop. And i really don't want the PC to run 24 H 
Right now the PSU supplying 2 x HEX16A, the HEX16A2 still not arrived yet.

[stan258]

I hope it comes molex.  I am not positive which wires to strip.

I ordered 2 (2 different dates though)
One came with molex, other came without.
If you have to strip, get a yellow and black. Yellow is +12v, black is GND. You can just cut off any molex connector, strip yellow and black to connect, and tape the red and other black to make sure they don't touch anything.

Thanks.  I bought molex connectors just in case to strip. 

[blitzwilli1]

can someone please give exact size of board?
Width and length

[wunch]

I hope it comes molex.  I am not positive which wires to strip.

I ordered 2 (2 different dates though)
One came with molex, other came without.
If you have to strip, get a yellow and black. Yellow is +12v, black is GND. You can just cut off any molex connector, strip yellow and black to connect, and tape the red and other black to make sure they don't touch anything.

Thanks.  I bought molex connectors just in case to strip. 

My Mid november for december order arrived 23rd dec and had screw terminals. Think they are moving molex to special request

[cannachris]

I hope it comes molex.  I am not positive which wires to strip.

I ordered 2 (2 different dates though)
One came with molex, other came without.
If you have to strip, get a yellow and black. Yellow is +12v, black is GND. You can just cut off any molex connector, strip yellow and black to connect, and tape the red and other black to make sure they don't touch anything.

Thanks.  I bought molex connectors just in case to strip. 

My Mid november for december order arrived 23rd dec and had screw terminals. Think they are moving molex to special request

Just got my order yesterday as well and have them running on hexminer, but i can't connect to my preflashed tp-link router to configure it. On what ip adress should it reside?

[Zich]

can someone please give exact size of board?
Width and length

It's 10 cm X 15 cm

[Zich]

I hope it comes molex.  I am not positive which wires to strip.

I ordered 2 (2 different dates though)
One came with molex, other came without.
If you have to strip, get a yellow and black. Yellow is +12v, black is GND. You can just cut off any molex connector, strip yellow and black to connect, and tape the red and other black to make sure they don't touch anything.

Thanks.  I bought molex connectors just in case to strip.  

My Mid november for december order arrived 23rd dec and had screw terminals. Think they are moving molex to special request

Just got my order yesterday as well and have them running on hexminer, but i can't connect to my preflashed tp-link router to configure it. On what ip adress should it reside?

The default IP  is 192.168.0.99

[braindead]

Anyone can help me here ??

I can´t connect to TL-MR3020 router, it is connected to my other router, i´ve tried 192.168.0.99 and 192.168.0.99/24  and i can´t get connection

Another thing is can i connect different asics via the router ?? I mean hex16a and hex16a2 ?? How to make it and insert values for 2 different Asic´s ??

Another question is .. I´m using windows, how to ssh to router ??

Sorry for all this noob questions but i´m starting in Asic´s and this is all new to me so please be gentle

[Zich]

Anyone can help me here ??

I can´t connect to TL-MR3020 router, it is connected to my other router, i´ve tried 192.168.0.99 and 192.168.0.99/24  and i can´t get connection

Another thing is can i connect different asics via the router ?? I mean hex16a and hex16a2 ?? How to make it and insert values for 2 different Asic´s ??

Another question is .. I´m using windows, how to ssh to router ??

Sorry for all this noob questions but i´m starting in Asic´s and this is all new to me so please be gentle

What is your router & computer IP?

Yes, you can connect HEX16A, HEX16B, HEX16C & nanofury using powered usb hub to router.

For using SSH you need to know the IP first then configure the router via LUCI to activate the SSH.

[braindead]

I´ve send u a message

[Zich]

I´ve send u a message

Reply send  
Feel free to ask more 

[Zich]

A few hour ago my HEX16A2 arrived by UPS courier. 1 day late because custom officer work half day only on 26 december, so my package stay 1 night in airport.



Add power connector & heatsink to PIC



Then when i start the miner, the fan noise make me shock. So noisy. So i open it and tada Sunon PF92251V1-000U-S99 . Spec 46 dBA  

Code:

Air Flow	:	75 CFM
Bearing Type	:	Vapo
Brand/Series	:	DR Series
Configuration	:	Square
Current, Rating	:	0.31 A
Dimensions	:	3.6 x 3.6 x 1 (92 x 92 x 25) In. (mm)
Dimensions, Inches	:	3.6 x 3.6 x 1 In.
Dimensions, mm	:	92 x 92 x 25 mm
Direction	:	Exhaust over Struts
Fan Type	:	DC
Material	:	Plastic
Noise Level	:	46 dBA
Power, Rating	:	4.7 W
Primary Type	:	Fans
Rotation	:	CW
Size	:	3.6 x 1 (92 x 25) In. (mm)
Size, Fan	:	3.6 x 1 (92 x 25) In. (mm)
Speed	:	4500 RPM
Static Pressure	:	0.35 In. (H2O)
Termination	:	Leadwires
Type	:	Square
Voltage, Rating	:	12 VDC
Weight	:	103 g 

I can't let it run in bedroom with TPLINK. So i need run it on PC with WINDOWS 7 64 bit until got replacement FAN with 100 CFM 20 dBA.
This is what detected on device manager.



Ok, time to run HEX MINER 1.0.0.3

[loshia]

A few hour ago my HEX16A2 arrived by UPS courier. 1 day late because custom officer work half day only on 26 december, so my package stay 1 night in airport.



Add power connector & heatsink to PIC



Then when i start the miner, the fan noise make me shock. So noisy. So i open it and tada Sunon PF92251V1-000U-A99 . Spec 46 dBA  

Code:

Air Flow	:	75 CFM
Bearing Type	:	Vapo
Brand/Series	:	DR Series
Configuration	:	Square
Current, Rating	:	0.31 A
Dimensions	:	3.6 x 3.6 x 1 (92 x 92 x 25) In. (mm)
Dimensions, Inches	:	3.6 x 3.6 x 1 In.
Dimensions, mm	:	92 x 92 x 25 mm
Direction	:	Exhaust over Struts
Fan Type	:	DC
Material	:	Plastic
Noise Level	:	46 dBA
Power, Rating	:	4.7 W
Primary Type	:	Fans
Rotation	:	CW
Size	:	3.6 x 1 (92 x 25) In. (mm)
Size, Fan	:	3.6 x 1 (92 x 25) In. (mm)
Speed	:	4500 RPM
Static Pressure	:	0.35 In. (H2O)
Termination	:	Leadwires
Type	:	Square
Voltage, Rating	:	12 VDC
Weight	:	103 g 

So i can't let it run in bedroom with TPLINK. So i need run it on PC with WINDOWS 7 64 bit until got replacement FAN with 100 CFM
This is what detected on device manager.



Ok, times to run HEX MINER 1.0.0.3

Congrats

So i can't let it run in bedroom with TPLINK. So i need run it on PC with WINDOWS 7 64 bit until got replacement FAN with 100 CFM
Shame You did excellent wiring. Please report back how it works when you move it to tp-link
Thanks and happy mining
PS: Make sure that you set-default-to-a on the tplink  in order for both hexA and HexC to work on same host

[Zich]

Congrats

So i can't let it run in bedroom with TPLINK. So i need run it on PC with WINDOWS 7 64 bit until got replacement FAN with 100 CFM
Shame You did excellent wiring. Please report back how it works when you move it to tp-link
Thanks and happy mining
PS: Make sure that you set-default-to-a on the tplink  in order for both hexA and HexC to work on same host

Thanks loshia, i will post the result tomorrow when the NZXT FZ 200mm arrived