NefariousFool
Jr. Member
Offline
Activity: 36
Merit: 7
|
|
April 24, 2019, 06:56:59 PM |
|
Does anyone tried with rx580 on ethash?
Yes, I tried. It is useless if your cards have modded BIOS. It may be good for GDDR5 cards with not modded timings. Sadly the timings need to be adjusted to make the tool work properly. still working on an effective method on this myself. However I can get .6 mhs improvement on Claymore 10.8 Eth. So there's something it will work just need to figure out the strategy still. I just have so many distractions it keeps me away.
|
|
|
|
SamAlackass
Newbie
Offline
Activity: 27
Merit: 1
|
|
April 24, 2019, 07:10:00 PM |
|
Seems to be working on 18.5.1 too if anyone is interested!
very interesting. if you can please share your results. rx580 gddr5 interesting. All internet timings is cool of course. but when timings I can tweak myself - that is cool. Please share your playing to start for noobies.. Thanks for early. I have very little to share atm I'm afraid. That was just a few quick runs on a single vega 56 test system, just trying to understand why WinAMDTweak isn't working at all in one of my systems, and I needed to make sure 18.5.1 wasn't the source of the problem. This is on a very un-optimized system and all but the last run, were only about an hour long. So please take everything with a grain of salt. All on the same system (vega 56 hynix), same ODNT settings (1350 core, 980 mem), CNR only. XMRig w/o memtweak 1650 h/s, with memtweak 1930 h/s TRM w/o 1935 h/s, with 2072 h/s (still running after 9 hours) Power consumption seemed about the same on all runs but I can't really tell from such short runs, and timings used were anwil's from a few pages back (thank you anwil!).
|
|
|
|
frozen80
Newbie
Offline
Activity: 18
Merit: 1
|
|
April 24, 2019, 07:49:30 PM |
|
Hi guys, I have a Sapphire Nitro+ Vega56 with default bios and Hynix memory with the defaults: GPU 0: Vega 10 XL/XT [Radeon RX Vega 56/64] Memory state: 0x118 (800MHz) Timing 1 CL: 18 RAS: 24 RCDRD: 22 RCDWR: 10 Timing 2 RCAb (RC): 37 RCPb (RC): 37 RPAb (RP): 13 RPPb (RP): 13 Timing 3 RRDS: 3 RRDL: 3 RTP: 6 Timing 4 FAW: 13 Timing 5 CWL: 6 WTRS: 4 WTRL: 4 Timing 6 WR: 12 Timing 7 RREFD: 7 Timing 8 RDRDDD: 3 RDRDSD: 2 RDRDSC: 1 RDRDSCL: 3 Timing 9 WRWRDD: 3 WRWRSD: 2 WRWRSC: 1 WRWRSCL: 3 Timing 10 WRRD: 1 RDWR: 18 Timing 12 REF: 3200 Timing 13 MRD: 4 MOD: 12 Timing 14 XS: 216 Timing 16 XSMRS: 216 Timing 17 PD: 7 CKSRE: 8 CKSRX: 8 Timing 20 RFCPB: 96 STAG: 7 Timing 21 XP: 7 CPDED: 2 CKE: 7 Timing 22 RDDATA: 17 WRLAT: 4 RDLAT: 14 WRDATA: 1 Timing 23 CKESTAG: 2 RFC Timing RFC: 176
Until now the only value i could change was --ref 12800 which increased the hashrate from 18.5 to 19.5 kh on cn-turtle. I'm using TR4.4 with L22+22 and driver 18.6.1. Unfortunately with other values posted here i had no luck What values do you think i could try to change based on my defaults?
|
|
|
|
reaper7881
Newbie
Offline
Activity: 27
Merit: 0
|
|
April 24, 2019, 07:57:23 PM |
|
Same trm 0.4.3 works better for me
|
|
|
|
pbfarmer
Member
Offline
Activity: 340
Merit: 29
|
|
April 24, 2019, 08:42:24 PM |
|
Hi guys, I have a Sapphire Nitro+ Vega56 with default bios and Hynix memory with the defaults: GPU 0: Vega 10 XL/XT [Radeon RX Vega 56/64] Memory state: 0x118 (800MHz) Timing 1 CL: 18 RAS: 24 RCDRD: 22 RCDWR: 10 Timing 2 RCAb (RC): 37 RCPb (RC): 37 RPAb (RP): 13 RPPb (RP): 13 Timing 3 RRDS: 3 RRDL: 3 RTP: 6 Timing 4 FAW: 13 Timing 5 CWL: 6 WTRS: 4 WTRL: 4 Timing 6 WR: 12 Timing 7 RREFD: 7 Timing 8 RDRDDD: 3 RDRDSD: 2 RDRDSC: 1 RDRDSCL: 3 Timing 9 WRWRDD: 3 WRWRSD: 2 WRWRSC: 1 WRWRSCL: 3 Timing 10 WRRD: 1 RDWR: 18 Timing 12 REF: 3200 Timing 13 MRD: 4 MOD: 12 Timing 14 XS: 216 Timing 16 XSMRS: 216 Timing 17 PD: 7 CKSRE: 8 CKSRX: 8 Timing 20 RFCPB: 96 STAG: 7 Timing 21 XP: 7 CPDED: 2 CKE: 7 Timing 22 RDDATA: 17 WRLAT: 4 RDLAT: 14 WRDATA: 1 Timing 23 CKESTAG: 2 RFC Timing RFC: 176
Until now the only value i could change was --ref 12800 which increased the hashrate from 18.5 to 19.5 kh on cn-turtle. I'm using TR4.4 with L22+22 and driver 18.6.1. Unfortunately with other values posted here i had no luck What values do you think i could try to change based on my defaults? The settings I've found to generally have the most impact after REF are RP (then change RC accordingly using RC = RP + RAS), and RCDRD/RCDWR. Just start dropping them 1 at a time until you see errors, then go back 1. Work w/ one parameter at a time so you know which is causing the errors.
|
|
|
|
bobymoore
Newbie
Offline
Activity: 61
Merit: 0
|
|
April 24, 2019, 09:25:28 PM |
|
Same trm 0.4.3 works better for me
When I said the same, someone said that I want to make a statement, I did not answer, but as you mentioned it, I will say what I have done so far. The truth is that due to lack of time I have not managed to run the tool, but I did a lot of testing. What I understand is that the 4.4 version is doing more, but finding the right driver and maybe a fresh installation of the windows. Trying one of the last drivers would be a better choice. A two-computer holder, on one I managed to catch 2150 hash, in both 56 @ 64 Vegas, I did not do much on the other computer on both 64s because one did not go over 1000 hash, that's from me. I will come back when I finally find time to use this wonderful tool, I came peacefully, with thirst for help and learning. Thanks again to the founder and those who help. I willI donate to the founder. Something last 2,5% fee to teamredminer is 2200x2,5÷100=55 hash? So it's fee?
|
|
|
|
Eliovp (OP)
Legendary
Offline
Activity: 1050
Merit: 1293
Huh?
|
|
April 25, 2019, 01:00:04 AM Last edit: April 25, 2019, 01:17:30 AM by Eliovp Merited by frodocooper (3) |
|
Hey all! Just to let you know that i've released a new GUI version with muchos improvements and options. A few of those.. - Bug Fixes
- Clock Control (Both Core and Memory)
- Fan Control (Curve)
- Export/Import values
- Reset option
- Removed EIO requirement
- ....
LinkSome shots
|
|
|
|
TheRealSTU
Newbie
Offline
Activity: 5
Merit: 0
|
|
April 25, 2019, 02:24:35 AM |
|
- Clock Control (Both Core and Memory)
Is this tool now a good substitute for PPT registry edit?
|
|
|
|
SigiSinatra
Newbie
Offline
Activity: 50
Merit: 0
|
|
April 25, 2019, 02:39:35 AM Last edit: April 25, 2019, 06:21:36 AM by SigiSinatra |
|
I can't start GUI version at all. I double click on .exe and nothing happens.
Version 0.1.7 worked and now it won't. Does .net framework (required for gui) maybe affects it ? I was getting 2400 h/s with vega 64 and 2200 h/s on vega 56 (64 bios) with Teamredminer. After restart it simply won't. I tried to run it as admin and without and still nothing.
Also, when I type winamdtweak.exe --current console just flash for sec and disappears. I tried with cmd /k but it doesn't work. If I try to run CMD as an administrator I get failed to load EIO.dll
Any solutions? Thank you
|
|
|
|
Mashy81
Jr. Member
Offline
Activity: 225
Merit: 1
|
|
April 25, 2019, 04:04:38 AM |
|
I can't start it. I double click on .exe and nothing happens.
Version 0.1.7 worked and now it won't. Does .net framework (required for gui) maybe affects it ? I was getting 2400 h/s with vega 64 and 2200 h/s on vega 56 (64 bios) Also, when I type winamdtweak.exe --current console just flash for sec and disappears. I tried with cmd /k but it doesn't work. If I try to run CMD as an administrator I get failed to load EIO.dll
Any solutions? Thank you
Are you using srb miner. This has happened to some people running srbminer
|
|
|
|
saltednutz
Newbie
Offline
Activity: 4
Merit: 0
|
|
April 25, 2019, 04:54:37 AM |
|
Hi guys, I have a Sapphire Nitro+ Vega56 with default bios and Hynix memory with the defaults: GPU 0: Vega 10 XL/XT [Radeon RX Vega 56/64] Memory state: 0x118 (800MHz) Timing 1 CL: 18 RAS: 24 RCDRD: 22 RCDWR: 10 Timing 2 RCAb (RC): 37 RCPb (RC): 37 RPAb (RP): 13 RPPb (RP): 13 Timing 3 RRDS: 3 RRDL: 3 RTP: 6 Timing 4 FAW: 13 Timing 5 CWL: 6 WTRS: 4 WTRL: 4 Timing 6 WR: 12 Timing 7 RREFD: 7 Timing 8 RDRDDD: 3 RDRDSD: 2 RDRDSC: 1 RDRDSCL: 3 Timing 9 WRWRDD: 3 WRWRSD: 2 WRWRSC: 1 WRWRSCL: 3 Timing 10 WRRD: 1 RDWR: 18 Timing 12 REF: 3200 Timing 13 MRD: 4 MOD: 12 Timing 14 XS: 216 Timing 16 XSMRS: 216 Timing 17 PD: 7 CKSRE: 8 CKSRX: 8 Timing 20 RFCPB: 96 STAG: 7 Timing 21 XP: 7 CPDED: 2 CKE: 7 Timing 22 RDDATA: 17 WRLAT: 4 RDLAT: 14 WRDATA: 1 Timing 23 CKESTAG: 2 RFC Timing RFC: 176
Until now the only value i could change was --ref 12800 which increased the hashrate from 18.5 to 19.5 kh on cn-turtle. I'm using TR4.4 with L22+22 and driver 18.6.1. Unfortunately with other values posted here i had no luck What values do you think i could try to change based on my defaults? The settings I've found to generally have the most impact after REF are RP (then change RC accordingly using RC = RP + RAS), and RCDRD/RCDWR. Just start dropping them 1 at a time until you see errors, then go back 1. Work w/ one parameter at a time so you know which is causing the errors. hey farmer, are you still using ppt at all? the ones from the past?
|
|
|
|
SamAlackass
Newbie
Offline
Activity: 27
Merit: 1
|
|
April 25, 2019, 08:15:19 AM |
|
Not working for me either. No errors, just nothing happens. On two different windows systems, 18.5.1.
|
|
|
|
livada
Newbie
Offline
Activity: 417
Merit: 0
|
|
April 25, 2019, 08:21:38 AM Last edit: April 25, 2019, 08:39:07 AM by livada |
|
not work- old version work. why? i dont now i try all but not start i try to win10pro win 10home and win7 64bit -not work --- pls . how i see current mem? i try in win and CMD. WinAMDTweak.exe --curent and WinAMDTweak.exe -current but not work.
|
|
|
|
saltednutz
Newbie
Offline
Activity: 4
Merit: 0
|
|
April 25, 2019, 08:47:49 AM |
|
not work- old version work. why? i dont now i try all but not start i try to win10pro win 10home and win7 64bit -not work --- pls . how i see current mem? i try in win and CMD. WinAMDTweak.exe --curent and WinAMDTweak.exe -current but not work. did you try WinAMDTweak.exe --current? or was that a typo?
|
|
|
|
livada
Newbie
Offline
Activity: 417
Merit: 0
|
|
April 25, 2019, 09:01:45 AM |
|
not work- old version work. why? i dont now i try all but not start i try to win10pro win 10home and win7 64bit -not work --- pls . how i see current mem? i try in win and CMD. WinAMDTweak.exe --curent and WinAMDTweak.exe -current but not work. did you try WinAMDTweak.exe --current? or was that a typo? yes i try. this is typo:) EDIT: i solved. when start in CMD WinAMDTweak.exe --current he start but only 0,00001sec and close and i not see this windows in TeamViever(NET slovly) now i use tweak curent.bat and comand WinAMDTweak.exe --current pause and now i see new GUI not work
|
|
|
|
SigiSinatra
Newbie
Offline
Activity: 50
Merit: 0
|
|
April 25, 2019, 09:31:48 AM |
|
not work- old version work. why? i dont now i try all but not start i try to win10pro win 10home and win7 64bit -not work --- pls . how i see current mem? i try in win and CMD. WinAMDTweak.exe --curent and WinAMDTweak.exe -current but not work. did you try WinAMDTweak.exe --current? or was that a typo? yes i try. this is typo:) EDIT: i solved. when start in CMD WinAMDTweak.exe --current he start but only 0,00001sec and close and i not see this windows in TeamViever(NET slovly) now i use tweak curent.bat and comand WinAMDTweak.exe --current pause and now i see new GUI not work It doesn't work for me. I added WinAMDTweak.exe --current PAUSE in .bat file and it still disappears almost instantly.
|
|
|
|
logicalray77
Jr. Member
Offline
Activity: 66
Merit: 4
|
|
April 25, 2019, 09:54:02 AM |
|
Interested to see what RX580 results are like. Please share if any... I have 120 cards and a boost would help.
|
|
|
|
livada
Newbie
Offline
Activity: 417
Merit: 0
|
|
April 25, 2019, 02:30:58 PM |
|
vega 56-hynix i use this setup --rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(
what i must chage? what step i must use? etc: rp14 to rp15 rfc 156 chg to rfc 157 ? or i must use 168 or higher?
what step use ? 1? or nubmer /with 8 or 16?
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...
i try down mem 1100 to 1090mhz but again have error i try give more power. now work with 870mv and i try with 920mv but again have error
pls any tutotrial what formula work with rp rc rfc ref etc....
|
|
|
|
Zorg33
Jr. Member
Offline
Activity: 144
Merit: 2
|
|
April 25, 2019, 02:53:38 PM |
|
vega 56-hynix i use this setup --rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(
what i must chage? what step i must use? etc: rp14 to rp15 rfc 156 chg to rfc 157 ? or i must use 168 or higher?
what step use ? 1? or nubmer /with 8 or 16?
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...
i try down mem 1100 to 1090mhz but again have error i try give more power. now work with 870mv and i try with 920mv but again have error
pls any tutotrial what formula work with rp rc rfc ref etc....
read back a little for formulas if your hynix memclk is really 1100 then and it's stable at stock timings, then rfc and rc and rcdwr are too low imho.
|
|
|
|
Gtx1070rig
Jr. Member
Offline
Activity: 56
Merit: 4
|
|
April 25, 2019, 03:40:15 PM |
|
I can't start GUI version at all. I double click on .exe and nothing happens.
Version 0.1.7 worked and now it won't. Does .net framework (required for gui) maybe affects it ? I was getting 2400 h/s with vega 64 and 2200 h/s on vega 56 (64 bios) with Teamredminer. After restart it simply won't. I tried to run it as admin and without and still nothing.
Also, when I type winamdtweak.exe --current console just flash for sec and disappears. I tried with cmd /k but it doesn't work. If I try to run CMD as an administrator I get failed to load EIO.dll
Any solutions? Thank you
Use full path "C:\PathtoAmdMemTweak\winamdtweak.exe --curren" pause? And run as admin ...
|
|
|
|
|