Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[laik2]

Hello everyone,

can you guys share with me your oc settings?

Mine is

GTX 1080
0core/1900mem/120W
getting average 37.5 MHs

GTX 1070 TI
0core/1250mem/105W
getting average 31.7 MHs

I am using linux (HiveOS). Windows uses another metric so it's hard to compare. Or do you know how to convert windows mem oc value to linux mem oc value? ;-)

im curious about your results, thanks.

linux memclk = windows*2

[1714109316]

1714109316

[1714109316]

1714109316

[1714109316]

1714109316

[1714109316]

1714109316

[Bael]

Hi

I'm trying to use the -strap option and I think I do something wrong, it gives me less mh/s than modifying the bios

16:59:17:889   93c   Driver version: 0x802
16:59:17:896   93c   driver init ok
16:59:18:032   93c   GPU #0 strap "POL8S1" is applied successfully
16:59:18:033   93c   GPU# 0 -rxboost option is applied successfully
16:59:19:074   93c   SSL: Imported 48 certificates from local storage

17:00:52:607   16b4   
17:00:52:608   16b4   GPU #0: Ellesmere (Radeon RX 580 Series), 8192 MB available, 36 compute units (pci bus 1:0:0)
17:00:52:608   16b4   ETH - Total Speed: 24.849 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
17:00:52:609   16b4   ETH: GPU0 24.849 Mh/s
17:00:52:609   16b4   Incorrect ETH shares: none
17:00:52:610   16b4   1 minute average ETH total speed: 24.777 Mh/s
17:00:52:610   16b4   Pool switches: ETH - 0
17:00:52:611   16b4   Pool shares accepting time (1 hour stats) - min 0 ms, max 0 ms, average 0 ms
17:00:52:612   16b4   Current ETH share target: 0x0000000112e0be82 (diff: 4000MH), epoch 293(3.29GB)
17:00:52:612   16b4   Current -dcri values: -dcri 20
17:00:52:613   16b4   GPU0 t=66C fan=28% P=75W
17:00:52:613   16b4   Total GPUs power consumption: 75 Watts
17:00:52:614   16b4   
17:00:53:134   d28   buf: {"id":0,"jsonrpc":"2.0","result":["0x374478554ad501f6b7d37f314f27646d48ced8f4f8a8f5e4182e243269f73eb5","0xc1bacb003fd7a885305dedf1660dd0dde1a7a39298fb341ae8253bd86312a501","0x0000000112e0be826d694b2e62d01511f12a6061fbaec8bc02357593e70e52ba","0x865644"]}

17:00:53:134   d28   ETH: 10/24/19-17:00:53 - New job from eu1.ethermine.org:4444
17:00:53:135   d28   target: 0x0000000112e0be82 (diff: 4000MH), epoch 293(3.29GB)
17:00:53:135   d28   ETH - Total Speed: 24.842 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:01
17:00:53:136   d28   ETH: GPU0 24.842 Mh/s


modifying the bios and without using -strap gives me about 30 mh/s

What could be the cause?

sorry for writing bad english

Regards

[tg88]

I'm trying to use the -strap option and I think I do something wrong, it gives me less mh/s than modifying the bios

To make it easier for us to check, please enter a full command line option here.

In this test was the gpu with the original or modified BIOS?

[Bael]

I'm trying to use the -strap option and I think I do something wrong, it gives me less mh/s than modifying the bios

To make it easier for us to check, please enter a full command line option here.

In this test was the gpu with the original or modified BIOS?

Hi

my star.bat

thDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xD69af2A796A737A103F12d2f0BCC563a13900E6F -epsw x -rxboost 1 -strap POL8S4 -cclock 1200 -cvddc 850 -mclock 2020 -mvddc 900 -dcri 20


With the original bios, I did the test first by overclocking with overdriventool and then with the star.bat as you can see in what I copied

win ver 1903 and amd driver 19.10.1

[1033ruben]

I am getting a hard reset everytime I try any of the straps. I have testing mode enabled, secure boot off, driver 19.4.1 installed and 8 hynix rx580 8gb cards on win 10. When it goes to apply straps, it gets to the point where it shows the strap has been applied to the 2nd card and then...boom, reset. Tried with all levels of strap (1->5). I am setting the clocks with overdriventool externally, at 1751mhz (pretty low for testing sake).

The same thing is happening to me.I am at my wits end with this rig PLEASE SOME ONE ANYONE HELP!!! so i have a 6x rx rig with 4 x470 and 2 x570 all 8gb. ok so like a few days ago it crashed right and this is after a month of solid mining with no resets or reboots or crashes. so things that i have tried i replaced the psu with a 1200 watt seasonic prime which is more than enough, i also switched out mobo from a gigabyte h110 dm3 to a asrock  btc pro, i have tried lowering the clocks, i have tried mining on just the rx470s and the 570s all to no avail, the only thing i havent done yet is switch out all the risers i am waiting on mine to arrive which is tomorrow. but i highly doubt that will fix the issue as i am able to mine with phoneix miner but the hashrate is pretty shittty. i mean going from 191 mh/s to 90 something is unacceptable. so please any one some one please help i am open to any suggestions at this point.

Have you tried to DDU yet?

yes tried that multiple times with a gang of drivers and even went as far as too reinstall windows on a different ssd and all...
ANYONE HELP!!! Please

[batsonxl]

I'm trying to use the -strap option and I think I do something wrong, it gives me less mh/s than modifying the bios

To make it easier for us to check, please enter a full command line option here.

In this test was the gpu with the original or modified BIOS?

Hi

my star.bat

thDcrMiner64.exe -epool eu1.ethermine.org:4444 -ewal 0xD69af2A796A737A103F12d2f0BCC563a13900E6F -epsw x -rxboost 1 -strap POL8S4 -cclock 1200 -cvddc 850 -mclock 2020 -mvddc 900 -dcri 20


With the original bios, I did the test first by overclocking with overdriventool and then with the star.bat as you can see in what I copied

win ver 1903 and amd driver 19.10.1

my friend you you are using strap wrong.Read the file from claymore,
-strap 1  or -strap 2 etc....
delete pol8s4 just write -strap 1

[Jonet]

Will the latest version work with the latest Windows 10  builds?  

Been a while since I have mined but figured I might as well heat my house with my miners this winter.  

I remember trying to turn of windows updates and it was impossible, would wake up to tragedy... I wonder if windows ever addressed that?

Thanks everyone, mine on!  Someday our ships will come in.  

========================EDIT:==========================

OK> this should do it: How to permanently disable windows updates:  

https://www.youtube.com/watch?v=KHvQVZSUbes

>>>>>>>

New question:  Which windows 10 build seems to work best? Thanks

If I remember correctly we stayed on 1709 for a while because 1803 caused the miner to take a long pause or stop. Also ATIFlash was not supported by 1803. Both issues are fixed and you can use any build. I let mine update to the latest. I think it's a good idea to at least stay on a build that is still supported by Microsoft.
Microsoft has changed it's policy a bit, they no longer push new builds automatically, you have to start the update manually. You get updates to the build you are on as long as it's supported and get reminded that your build is near end of support. I'm not sure if they will push the new build if you reach the end of support date.

[Ursul0]

what's the actual best secundary coin to mine with ETH on claymore?

try xvg maybe? but as mentioned earlier it may not worth it to stress the cards, even if your electricity cost is zero. it was fun two years ago for ~15% increase in consumption you could get over 10% increase comparing to ETH produced. not the case now:)

[1033ruben]

I am getting a hard reset everytime I try any of the straps. I have testing mode enabled, secure boot off, driver 19.4.1 installed and 8 hynix rx580 8gb cards on win 10. When it goes to apply straps, it gets to the point where it shows the strap has been applied to the 2nd card and then...boom, reset. Tried with all levels of strap (1->5). I am setting the clocks with overdriventool externally, at 1751mhz (pretty low for testing sake).

The same thing is happening to me.I am at my wits end with this rig PLEASE SOME ONE ANYONE HELP!!! so i have a 6x rx rig with 4 x470 and 2 x570 all 8gb. ok so like a few days ago it crashed right and this is after a month of solid mining with no resets or reboots or crashes. so things that i have tried i replaced the psu with a 1200 watt seasonic prime which is more than enough, i also switched out mobo from a gigabyte h110 dm3 to a asrock  btc pro, i have tried lowering the clocks, i have tried mining on just the rx470s and the 570s all to no avail, the only thing i havent done yet is switch out all the risers i am waiting on mine to arrive which is tomorrow. but i highly doubt that will fix the issue as i am able to mine with phoneix miner but the hashrate is pretty shittty. i mean going from 191 mh/s to 90 something is unacceptable. so please any one some one please help i am open to any suggestions at this point.

Have you tried to DDU yet?

yes tried that multiple times with a gang of drivers and even went as far as too reinstall windows on a different ssd and all...
ANYONE HELP!!! Please

So then nothing huh...

[NCarter84]

I am getting a hard reset everytime I try any of the straps. I have testing mode enabled, secure boot off, driver 19.4.1 installed and 8 hynix rx580 8gb cards on win 10. When it goes to apply straps, it gets to the point where it shows the strap has been applied to the 2nd card and then...boom, reset. Tried with all levels of strap (1->5). I am setting the clocks with overdriventool externally, at 1751mhz (pretty low for testing sake).

The same thing is happening to me.I am at my wits end with this rig PLEASE SOME ONE ANYONE HELP!!! so i have a 6x rx rig with 4 x470 and 2 x570 all 8gb. ok so like a few days ago it crashed right and this is after a month of solid mining with no resets or reboots or crashes. so things that i have tried i replaced the psu with a 1200 watt seasonic prime which is more than enough, i also switched out mobo from a gigabyte h110 dm3 to a asrock  btc pro, i have tried lowering the clocks, i have tried mining on just the rx470s and the 570s all to no avail, the only thing i havent done yet is switch out all the risers i am waiting on mine to arrive which is tomorrow. but i highly doubt that will fix the issue as i am able to mine with phoneix miner but the hashrate is pretty shittty. i mean going from 191 mh/s to 90 something is unacceptable. so please any one some one please help i am open to any suggestions at this point.

Have you tried to DDU yet?

yes tried that multiple times with a gang of drivers and even went as far as too reinstall windows on a different ssd and all...
ANYONE HELP!!! Please

So then nothing huh...

Going from 190 to 90 mhs = your drivers aren't in compute mode.

Honestly, PM is faster overall.... Set drivers to compute, download the tweak tool and set tref to 30 and see where you end up.... My (6) card rig of 470s run 197 mhs on PM.

[Derloda]

Hi,

I'm using the 15.0 miner version on Linux with 3 AMD cards, 2x R9 390X and 1x RX VEGA64, but it seems like the miner only recognize either the two R9 or only the RX, even if the three are recognized by the system ?

Is there a potential fix for this issue ?

Thanks in advance

[Bael]

Hi

I've started using Claymore again and I'm lost, I've been testing -rxboost and -strap, more mh/s ^^

But I have a doubt, I tried the original bios and everything works fine, if I apply it to a previously modified bios, does it work well?

I did a test and I think it doesn't work well with the previously modified bios.

Do I have to use the original bios of each gpu?

sorry for writing bad english

Regards : )

[tg88]

But I have a doubt, I tried the original bios and everything works fine, if I apply it to a previously modified bios, does it work well?

Do I have to use the original bios of each gpu?

To use the parameter - strap it is ideal that all your gpus are running with the original BIOS, this must be the reason for your problems.

[Bael]

But I have a doubt, I tried the original bios and everything works fine, if I apply it to a previously modified bios, does it work well?

Do I have to use the original bios of each gpu?

To use the parameter - strap it is ideal that all your gpus are running with the original BIOS, this must be the reason for your problems.

I will do so, thank you very much! : )

[Bael]

Hi

I am having trouble knowing when the gpu is stable, I have always used HWinfo to see gpu memory errors and if I had no errors it was stable.

Now it marks errors with a lot of oc or without any oc, I deduce that it is when applying -strap

I leave some screenshots, using memory at 2000 (default) or 2240 always gives memory errors





How could I test the stability of a gpu? many to try that the problem

regards!!  : )

[SLcharger]

My rigs running with 4GB Nitro GPU's are utilizing 3.4GB onboard RAM, and 4.8GB Vitual Memory each.

On my H110's I have Vitual Memory settings to 65536 MB, with 12 GPU.

Running fine on Claymore 11.5, don't work on 14.5.

[Dunker23]

Hi guys,

I have a weird issue since claymore 14.5 with my Gigabyte 1070 8gb.

I have a rig with 3 AMD rx 580, 2 1070, and 2 1070 Ti.

Before 14.5 1070s had hashrate of around 32MHs, with settings: -300 +600 powlimit -38

Since I updated the claymore, hashrate on 1070s dropped to around 27MHs. 1070Tis are working fine and its hashrate actually improved from 32 to 34.

If I want to have 32MHs on 1070s I have to set core clock to +100 and powlimit to -20. This setting uses much more power.
Any idea why is this happening?

Best Regards

[KOVIC]

Will the latest version work with the latest Windows 10  builds?  

Been a while since I have mined but figured I might as well heat my house with my miners this winter.  

I remember trying to turn of windows updates and it was impossible, would wake up to tragedy... I wonder if windows ever addressed that?

Thanks everyone, mine on!  Someday our ships will come in.  

========================EDIT:==========================

OK> this should do it: How to permanently disable windows updates:  

https://www.youtube.com/watch?v=KHvQVZSUbes

>>>>>>>

New question:  Which windows 10 build seems to work best? Thanks

If I remember correctly we stayed on 1709 for a while because 1803 caused the miner to take a long pause or stop. Also ATIFlash was not supported by 1803. Both issues are fixed and you can use any build. I let mine update to the latest. I think it's a good idea to at least stay on a build that is still supported by Microsoft.
Microsoft has changed it's policy a bit, they no longer push new builds automatically, you have to start the update manually. You get updates to the build you are on as long as it's supported and get reminded that your build is near end of support. I'm not sure if they will push the new build if you reach the end of support date.

HELO!

FOr miner use Windows 10  Pro RS3 X64 Build v1709.16299.192
to STOP Windows 10 Automatic Updates (gpedit & regedit)

Have fun!

[Kumic]

I used older versions of Claymore without -strap and -rxboost options.
When I tried latest version with -strap and -rxboost option I got a very nice gains. My cards (470s, 570s, 580s) went up above 32mh, 33mh.
But that was all reported hashrate. Truth was that my current hashrate dropped and I mined much less than earlier.
Maybe I was doing something wrong

[Bael]

I used older versions of Claymore without -strap and -rxboost options.
When I tried latest version with -strap and -rxboost option I got a very nice gains. My cards (470s, 570s, 580s) went up above 32mh, 33mh.
But that was all reported hashrate. Truth was that my current hashrate dropped and I mined much less than earlier.
Maybe I was doing something wrong

I've been testing a gpu in ethermine for two days and it gives me more benefits than any other miner I've tried.

My only doubt is the stability that I can have, the maximum I have had the gpu is 40 min, I am using my personal pc

It gives me many memory errors according to hwinfo, I plan to put a 6 gpus rig in principle

Please, could you tell me who reads if with these memory errors the gpus could be stable?

screenshots:

https://imgur.com/ZNssF1U

https://imgur.com/ULGkbaB

Regards : )