Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[WBrainDamage]

Hello all!

Been trying to setup Claymore for sometime now, with no luck. I´m running the exe file with the config file like this:

-epool http://eth.2miners.com:2020
-ewal 0xF907F7669620565b45f92DFa5C59B4ee75318359
-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
-esm 0
-mode 1
#-tt 70
#-asm 0
-etha 0
-dbg 1

Claymore initializes  and then exits.

The debug file as follows:

23:30:16:182   155c   Check and remove old log files...
23:30:16:183   155c   args: -epool http://eth.2miners.com:2020 -ewal 0xF907F7669620565b45f92DFa5C59B4ee75318359 -epsw x -esm 0 -mode 1 -etha 0 -dbg 1
23:30:16:184   155c   
23:30:16:184   155c   ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
23:30:16:185   155c   º                Claymore's Dual GPU Miner - v11.9               º
23:30:16:186   155c   º              ETH + DCR/SIA/LBC/PASC/BLAKE2S/KECCAK             º
23:30:16:187   155c   ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
23:30:16:188   155c   
23:30:16:189   155c   b597
23:30:16:390   155c   ETH: 1 pool is specified
23:30:16:391   155c   Main Ethereum pool is eth.2miners.com:2020
23:30:16:535   155c   OpenCL platform: AMD Accelerated Parallel Processing
23:30:16:535   155c   OpenCL platform: AMD Accelerated Parallel Processing
23:30:16:537   155c   OpenCL initializing...

23:30:16:538   155c   AMD Cards available: 1
23:30:16:538   155c   GPU #0: Ellesmere (Radeon RX 570 Series), 8192 MB available, 32 compute units (pci bus 1:0:0)
23:30:16:539   155c   GPU #0 recognized as Radeon RX 470/570
23:30:16:540   155c   POOL/SOLO version
23:30:16:540   155c   Platform: Windows
23:30:16:591   155c   start building OpenCL program for GPU 0...


Can someone help me?

probably read the "README!" file as well. It says something about 5% reduction for including http://

Thanks for the heads up! 

Will change it!

[Binary100100]

Another piece of advice, stop using your wallet! They might have your private keys. By continuing to use your old wallet you could pretty much be paying them without knowing it and they're just waiting for the perfect time to clean you out again.

So unless you have some solid proof please stop accusing a hardworking developer. Accusations on here without evidence is defamation and libel. It literally make HIM a victim. If you have (or think you have) sufficient evidence then go to law enforcement. Good luck with that.

BTW, with mining profitability starting to regain popularity I'd definitely be on your guard. We're all potential victims.

I no longer use that wallet.
Proving the theft of cryptocurrency in this world is not possible.
But it still happened neither earlier nor much later, as the miner was downloaded from the developer (although this was not the case before). But we are all human, and people have a weakness to succumb to greed. And the more they have, the more they want more.

(Sigh)
I don't think you're fully grasping anything that I (apparently wasted my time) have been trying to explain to you.

Look I'm very sorry for your ~$6,900 USD loss. I don't see ETH hitting $1,000 anytime soon though. FYI. I'd say in maybe 5+ years or so but anyway... you're wasting your time chasing something that didn't happen and defaming someone in the process.

Tell you what. Give us all your unprotected IP address and I'll show you how easy it is to steal your crypto. It probably won't happen immediately but it will happen! And it won't be from downloading a .bat file. The ONLY reason why any anti-viruses go off is because it's a MINER. I can't think of any that don't set off anti-virus software. I've come across WEBSITES that try to mine crypto.
Also, here's what didn't make sense to me. You have your wallet (JAXX) on your computer that you mine on? That doesn't make any sense. If you didn't, then why would you execute the software on a computer that you're not mining on? It's not adding up. Or are you suggesting that by simply downloading it (not executing) he was somehow able to hack your machine? Not saying it's impossible but highly unlikely. Or perhaps you installed it on your mining computers and he hacked a different computer on  your network??? How would he do that when the virus isn't on that computer??? See what I mean? Too many issues with your accusations. There is no solid proof anywhere. You haven't provided a wallet address to where your funds went, no ip address, no method of attack. You said that JAXX just mysteriously opened up and sent your funds away before your eyes. I'm telling you the only way to do that is by RDP or something similar such as Teamviewer or Chrome Remote Desktop. But if you're so concerned about it happening again then uninstall all of your wallets and restore them as needed. Can't hack what isn't there, right?

Any case, I'm actually glad that it happened to you. Not to sound like a jerk but I think that's it's better to happen when you have 1 BTC stored in your wallet than 10 BTC. My guess is someone hacked your crap a while ago and already had access. They were just waiting for the perfect moment to strike. Maybe they thought, "He just downloaded something that runs a mining script. I bet he'll blame that instead of trying to track the real source! I'll do this now!" So while you're wasting time and energy defaming a hard working developer for something he didn't do the thief is transferring your funds and spending your money so even IF you could identify him/her you couldn't get it back.

But hey... what do I know? I'm only speaking from experience.

[Wcrypto]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working). 

Anyone can help me please?

Thank you!
 

[WhyMe]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working).  

Anyone can help me please?

Thank you!
 

mvddc is memory voltage, not core.
I don't know why but you must always use -cvddc AND -mvddc with the same value on RX

[Wcrypto]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working).  

Anyone can help me please?

Thank you!
 

mvddc is memory voltage, not core.
I don't know why but you must always use -cvddc AND -mvddc with the same value on RX

Yes, I do use both with the same value in my commande line.

[WhackOBill]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working).  

Anyone can help me please?

Thank you!
 

mvddc is memory voltage, not core.
I don't know why but you must always use -cvddc AND -mvddc with the same value on RX

I believe -mvddc is memory controller voltage, not the actual memory voltage which is non-adjustable on these cards.  I run separate values for core and memory controller with no issues on RX580s.

[Geniusvzla]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working). 

Anyone can help me please?

Thank you!
 

Regards,
here you need more data: If you use afterbuner it indicates what values ​​you have there and in your belt configuration what values ​​you put on! if you use -mvdcc 850 and -cvddc 850 you should increase it or 900 or 950 each! On the contrary, if you want to keep the 850 you should lower the memory clock until it is stable; Afterwards if your Mh / s are very low you may have to try another belt or return to the one you had previously. Sorry my bad english

[Wcrypto]

Hi,

I tried to bring back my RX580 (Red devil 8gb Samsung) to the original bios in order to use claymore 14.7 with rxboost and the strap function. (I use windows 10)

My problem is that every time I try to set-up the core voltage in claymore (I use -mvdcc 850) , the system crash almost immediately. (blank screen).

If I don't use the -mvdcc command, it is working and I get 10% more mh/s but I use 25% more watt than before so it is not very good.

I have tried to change the core voltage in MS afterburner (Core voltage -100)  but it doesn't have any effect on my power consumption….(like if it was not working). 

Anyone can help me please?

Thank you!
 

Regards,
here you need more data: If you use afterbuner it indicates what values ​​you have there and in your belt configuration what values ​​you put on! if you use -mvdcc 850 and -cvddc 850 you should increase it or 900 or 950 each! On the contrary, if you want to keep the 850 you should lower the memory clock until it is stable; Afterwards if your Mh / s are very low you may have to try another belt or return to the one you had previously. Sorry my bad english

Thanks for your answer but the miner is already stable with my bios modded card, I have a problem when I get back to original bios and I try to use "-strap" and "-rxboost" command with exactly the same command line...

[Wcrypto]

Can we use the -strap command with a bios modified card?

[STT]

My antivirus removed the file as soon as it was available.

So ill keep off until some more comments are available

All these years later and yep, my ethdcrminer64 is kidnapped by some ever so friendly stupid software.   It does at least force me to update to the latest version since I've completely lost track of whatever dungeon the old .exe has been placed in

Is there any preference between 14.6 and 14.7 at the moment, using vega

[Chrome also says its a dangerous download, but at least lets me decide in finality for myself.   just fyi for my fellow noobs ]

[destinys]

Hi Claymore,

i think alot of us got the RX5700 graphics card waiting for the software to be updated the community alot of us is waiting. Is there any updates or any finding which able for us to mine. Thanks

Regards
Melvin

[jeremyismer]

Can we use the -strap command with a bios modified card?

Yeah, you can. I ran it on mine, but I didn't get any better performance than the straps I had myself. Others have suggested to reflash back to stock and run strap and rxboost, but at the moment I'm not fixing what ain't broken.

[4ward]

Hello!
With dual mining ETH+Pascal, the number of rejected shares for Pascal is about 50%. Can this be fixed someway?
Thanks!

Its a surprise that there are accepted shares, since Pascal coin changed their algo completely

[gianb]

My claymore its working fine but, when I start claymore a message appears in red that says Unknown option 1

[UnclWish]

My claymore its working fine but, when I start claymore a message appears in red that says Unknown option 1

It's simple - you must remove option "1" from command line to launch miner.

[gianb]

My claymore its working fine but, when I start claymore a message appears in red that says Unknown option 1

It's simple - you must remove option "1" from command line to launch miner.

%~dp0
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
:ini
timeout /t 20

EthDcrMiner64.exe -epool eth-us-east1.nanopool.org:9999 -ewal 0x3f8c701099e6748bc44938467121d8ff2c165.RGCCS01ETH -epsw x -tstop 75 -ftime 10 -allpools 1 -allcoins -1 -asm 1 -cclock 1090,1090,1090,1090,1090,1090 -mclock 2070,2070,2070,2060,2070,2070 -mvddc 900,900,900,910,900,900 -cvddc 900,900,900,910,900,900 -r 3600 -estale 1 -gser 2 -mode 1 -etha 0 -erate 1 -ttli 75 -y -platform 1 -tstart 60 -retrydelay 5 -mport 3333 -strap 1 -rxboost 1 -mpsw 748
end




Could you help me with what I should remove?

[WhackOBill]

My claymore its working fine but, when I start claymore a message appears in red that says Unknown option 1

It's simple - you must remove option "1" from command line to launch miner.

%~dp0
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
:ini
timeout /t 20

EthDcrMiner64.exe -epool eth-us-east1.nanopool.org:9999 -ewal 0x3f8c701099e6748bc44938467121d8ff2c165.RGCCS01ETH -epsw x -tstop 75 -ftime 10 -allpools 1 -allcoins -1 -asm 1 -cclock 1090,1090,1090,1090,1090,1090 -mclock 2070,2070,2070,2060,2070,2070 -mvddc 900,900,900,910,900,900 -cvddc 900,900,900,910,900,900 -r 3600 -estale 1 -gser 2 -mode 1 -etha 0 -erate 1 -ttli 75 -y -platform 1 -tstart 60 -retrydelay 5 -mport 3333 -strap 1 -rxboost 1 -mpsw 748
end


Could you help me with what I should remove?

You're missing the ' 1' after the -y it seems. 

[gianb]

My claymore its working fine but, when I start claymore a message appears in red that says Unknown option 1

It's simple - you must remove option "1" from command line to launch miner.

%~dp0
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
:ini
timeout /t 20

EthDcrMiner64.exe -epool eth-us-east1.nanopool.org:9999 -ewal 0x3f8c701099e6748bc44938467121d8ff2c165.RGCCS01ETH -epsw x -tstop 75 -ftime 10 -allpools 1 -allcoins -1 -asm 1 -cclock 1090,1090,1090,1090,1090,1090 -mclock 2070,2070,2070,2060,2070,2070 -mvddc 900,900,900,910,900,900 -cvddc 900,900,900,910,900,900 -r 3600 -estale 1 -gser 2 -mode 1 -etha 0 -erate 1 -ttli 75 -y -platform 1 -tstart 60 -retrydelay 5 -mport 3333 -strap 1 -rxboost 1 -mpsw 748
end


Could you help me with what I should remove?

You're missing the ' 1' after the -y it seems. 

Yes thanks!

[Junkey]

When I set -mclock and cclock in the miner and close it Windows 10 freezes for a bit and then resets the config to default.  Is there a more graceful way to do it that I am missing?  Thanks,

[sharmanov]

getting GPU #0 strap "1" failed, error 1002  how do I fix that and what does that error mean? all straps get that error