Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[Ra1s3r]

Hi everyone!

Yesterday i got the same issue with my 1050TI 4gb, not enough memory for dag generation. Checked everything, and it turned out that NV drivers 382.53 works fine on some of my rigs with this cards, so i downgraded drivers and now it works fine. Hope it helps ).

[dortortz]

Thank you! I will try that driver for my 1050ti. I hope this gets fixed soon with an update or something, I do like keeping my drivers up to date

[JoWannes]

So, my miner's motherboard died and SSD crashed. Got new motherboard and SSD today.
I had no backup of my previous system, so I reinstalled everything from scratch using latest versions.

Gigabyte GA-H110-D3A, 6x RX580 4GB

Before:
Win 10, I think build 1703 of 1709 (not sure)
AMD beta blockchain drivers
Claymore 11.9

Now:
Win 10 build 1903 (latest)
Latest AMD drivers
Claymore 15

Before I got  +- 182MH/s ETH only (as expected for this rig), but now something like 72 (+-12 per card, all 6 cards working). Something's obviously off.

Quick suggestions on what I did wrong? Which OS version and driver version should I use? Thanks!

[NCarter84]

So, my miner's motherboard died and SSD crashed. Got new motherboard and SSD today.
I had no backup of my previous system, so I reinstalled everything from scratch using latest versions.

Gigabyte GA-H110-D3A, 6x RX580 4GB

Before:
Win 10, I think build 1703 of 1709 (not sure)
AMD beta blockchain drivers
Claymore 11.9

Now:
Win 10 build 1903 (latest)
Latest AMD drivers
Claymore 15

Before I got  +- 182MH/s ETH only (as expected for this rig), but now something like 72 (+-12 per card). Something's obviously off.

Quick suggestions on what I did wrong? Which OS version and driver version should I use? Thanks!

Sounds like compute mode is not on.

[jpmonster]

Hi everyone!

Yesterday i got the same issue with my 1050TI 4gb, not enough memory for dag generation. Checked everything, and it turned out that NV drivers 382.53 works fine on some of my rigs with this cards, so i downgraded drivers and now it works fine. Hope it helps ).

Did not work for me:(
I guess no more ETC mining:(

[batsonxl]

Both v14.2 do BSOD with Vega and 19.5.1 when I use -strap.

PAGE_FAULT_IN_NONPAGED_AREA
cmdrv64.sys

Strap Drivers are already in use when you load another instance of the miner. Here is log from b711 version :

01:37:11:329   fcc   Driver is not installed! Trying to install it...
01:37:11:373   fcc   Driver is in use, try to start miner with "-driver uninstall" parameter.
01:37:11:792   fcc   SSL: Imported 76 certificates from local storage

Rgds

Dude run as ADMINISTRATOR

[JoWannes]

Sounds like compute mode is on.

Thanks for the hint. The registry edits I found here fixed it for me: https://monero.farm/disable-crossfire-and-enable-compute-mode-in-one-click/
Still running only 175~176MH/s instead of 182~183 before, but yeah, it will do for now.

[NCarter84]

Sounds like compute mode is on.

Thanks for the hint. The registry edits I found here fixed it for me: https://monero.farm/disable-crossfire-and-enable-compute-mode-in-one-click/
Still running only 175~176MH/s instead of 182~183 before, but yeah, it will do for now.

Nice! Are you running any of the straps or rxboost?

[Malwolficus]

I’m running the latest version on Ubuntu 16, from command line, and none of the “tt” or “r” options seem to work.  I have a card that stops hashing after an hour or two and a simple restart fixes it - but I have to restart the miner manually, no matter what I do the autorestart won’t autorestart.  How can I go about troubleshooting why this command doesn’t work?

[Binary100100]

So, my miner's motherboard died and SSD crashed. Got new motherboard and SSD today.
I had no backup of my previous system, so I reinstalled everything from scratch using latest versions.

Gigabyte GA-H110-D3A, 6x RX580 4GB

Before:
Win 10, I think build 1703 of 1709 (not sure)
AMD beta blockchain drivers
Claymore 11.9

Now:
Win 10 build 1903 (latest)
Latest AMD drivers
Claymore 15

Before I got  +- 182MH/s ETH only (as expected for this rig), but now something like 72 (+-12 per card). Something's obviously off.

Quick suggestions on what I did wrong? Which OS version and driver version should I use? Thanks!

Sounds like compute mode is on.

I think that you mean it sounds like it's on Graphics and not Compute.
I'd also recommend trying the beta blockchain drivers again and see what the difference is.

[Guigs321]

Sounds like compute mode is on.

Thanks for the hint. The registry edits I found here fixed it for me: https://monero.farm/disable-crossfire-and-enable-compute-mode-in-one-click/
Still running only 175~176MH/s instead of 182~183 before, but yeah, it will do for now.

I reach 33,1 MH/s per card with exactly the same setup here my settings for Claymore :

-dcri 24  -cclock 1220 -mclock 2200 -cvddc 900 -tt 65 -strap 2 -rxboost 1

[RAKOT]

Sounds like compute mode is on.

Thanks for the hint. The registry edits I found here fixed it for me: https://monero.farm/disable-crossfire-and-enable-compute-mode-in-one-click/
Still running only 175~176MH/s instead of 182~183 before, but yeah, it will do for now.

I reach 33,1 MH/s per card with exactly the same setup here my settings for Claymore :

-dcri 24  -cclock 1220 -mclock 2200 -cvddc 900 -tt 65 -strap 2 -rxboost 1

What GPU can reach such speed ?

[gedeonodn]

I’m running the latest version on Ubuntu 16, from command line, and none of the “tt” or “r” options seem to work.  I have a card that stops hashing after an hour or two and a simple restart fixes it - but I have to restart the miner manually, no matter what I do the autorestart won’t autorestart.  How can I go about troubleshooting why this command doesn’t work?

Use this script, run as root:

Code:

#!/bin/bash

if [ -z $1 ]
then
        echo "gpunum not set"
        exit 0
fi

managefilepath="/sys/class/drm/card$1/device/power_dpm_force_performance_level"
fanfilepath=$(find /sys/class/drm/card"$1"/device/hwmon -regextype posix-awk -regex ".*/hwmon[0-9]{1,2}")/pwm1_enable

chmod 666 "$managefilepath"
chmod 666 "$fanfilepath"
echo manual > "$managefilepath"
echo "1" > "$fanfilepath"

put gpu number in parameter, use for each card

[UnclWish]

Sounds like compute mode is on.

Thanks for the hint. The registry edits I found here fixed it for me: https://monero.farm/disable-crossfire-and-enable-compute-mode-in-one-click/
Still running only 175~176MH/s instead of 182~183 before, but yeah, it will do for now.

I reach 33,1 MH/s per card with exactly the same setup here my settings for Claymore :

-dcri 24  -cclock 1220 -mclock 2200 -cvddc 900 -tt 65 -strap 2 -rxboost 1

What GPU can reach such speed ?

Polaris. RX 580 8Gb. On Phoenix miner i have 34,2MH with cclock 1230 mclock 2250.

[big_daddy]

Polaris. RX 580 8Gb. On Phoenix miner i have 34,2MH with cclock 1230 mclock 2250.

Polaris ok, but what type of memory? Samsung, Elpida, Hynix, Micron?
And what is the power consumption of your card running on 34.2 MHs?

[UnclWish]

Polaris. RX 580 8Gb. On Phoenix miner i have 34,2MH with cclock 1230 mclock 2250.

Polaris ok, but what type of memory? Samsung, Elpida, Hynix, Micron?
And what is the power consumption of your card running on 34.2 MHs?

I have only with hynix. And it give 34.2MH on PM. Power consumption about 90-100W from sensor. About 125W from wall.

[zz0622]

Got the same problem either.

it shows "Driver is in use, try to start miner with "-driver uninstall" parameter" when I add "-strap 1" in batch file

I try to add "-driver uninstall" in the file and runs it but it shows it require Administrator to access it.

I add "runas /user:Administrator" in batch file but it just can't run appropriately and close the window rapidly.

My cards are gtx1070 with latest driver version 436.3 in Win10 64bit

May anyone please let me know how can I solve this problem?

Thank you for the kindly help.

Both v14.2 do BSOD with Vega and 19.5.1 when I use -strap.

PAGE_FAULT_IN_NONPAGED_AREA
cmdrv64.sys

Strap Drivers are already in use when you load another instance of the miner. Here is log from b711 version :

01:37:11:329   fcc   Driver is not installed! Trying to install it...
01:37:11:373   fcc   Driver is in use, try to start miner with "-driver uninstall" parameter.
01:37:11:792   fcc   SSL: Imported 76 certificates from local storage

Rgds

[NCarter84]

Got the same problem either.

it shows "Driver is in use, try to start miner with "-driver uninstall" parameter" when I add "-strap 1" in batch file

I try to add "-driver uninstall" in the file and runs it but it shows it require Administrator to access it.

I add "runas /user:Administrator" in batch file but it just can't run appropriately and close the window rapidly.

My cards are gtx1070 with latest driver version 436.3 in Win10 64bit

May anyone please let me know how can I solve this problem?

Thank you for the kindly help.

Both v14.2 do BSOD with Vega and 19.5.1 when I use -strap.

PAGE_FAULT_IN_NONPAGED_AREA
cmdrv64.sys

Strap Drivers are already in use when you load another instance of the miner. Here is log from b711 version :

01:37:11:329   fcc   Driver is not installed! Trying to install it...
01:37:11:373   fcc   Driver is in use, try to start miner with "-driver uninstall" parameter.
01:37:11:792   fcc   SSL: Imported 76 certificates from local storage

Rgds

Right click the miner, Properties and go to the Compatibility Tab and check the box "Run this program as an admin".
 

[zz0622]

I tried to set EthDcrMiner64.exe to run as administrator in properties page.

The window just pop up and close rapidly after I double click the batch |o|.

I'm using Win10 1709 and 1803 version. Is it too old to cause this issue?

Thank you mate : )

Got the same problem either.

it shows "Driver is in use, try to start miner with "-driver uninstall" parameter" when I add "-strap 1" in batch file

I try to add "-driver uninstall" in the file and runs it but it shows it require Administrator to access it.

I add "runas /user:Administrator" in batch file but it just can't run appropriately and close the window rapidly.

My cards are gtx1070 with latest driver version 436.3 in Win10 64bit

May anyone please let me know how can I solve this problem?

Thank you for the kindly help.

Both v14.2 do BSOD with Vega and 19.5.1 when I use -strap.

PAGE_FAULT_IN_NONPAGED_AREA
cmdrv64.sys

Strap Drivers are already in use when you load another instance of the miner. Here is log from b711 version :

01:37:11:329   fcc   Driver is not installed! Trying to install it...
01:37:11:373   fcc   Driver is in use, try to start miner with "-driver uninstall" parameter.
01:37:11:792   fcc   SSL: Imported 76 certificates from local storage

Rgds

Right click the miner, Properties and go to the Compatibility Tab and check the box "Run this program as an admin".
 

[NCarter84]

I tried to set EthDcrMiner64.exe to run as administrator in properties page.

The window just pop up and close rapidly after I double click the batch |o|.

I'm using Win10 1709 and 1803 version. Is it too old to cause this issue?

Thank you mate : )

Got the same problem either.

it shows "Driver is in use, try to start miner with "-driver uninstall" parameter" when I add "-strap 1" in batch file

I try to add "-driver uninstall" in the file and runs it but it shows it require Administrator to access it.

I add "runas /user:Administrator" in batch file but it just can't run appropriately and close the window rapidly.

My cards are gtx1070 with latest driver version 436.3 in Win10 64bit

May anyone please let me know how can I solve this problem?

Thank you for the kindly help.

Both v14.2 do BSOD with Vega and 19.5.1 when I use -strap.

PAGE_FAULT_IN_NONPAGED_AREA
cmdrv64.sys

Strap Drivers are already in use when you load another instance of the miner. Here is log from b711 version :

01:37:11:329   fcc   Driver is not installed! Trying to install it...
01:37:11:373   fcc   Driver is in use, try to start miner with "-driver uninstall" parameter.
01:37:11:792   fcc   SSL: Imported 76 certificates from local storage

Rgds

Right click the miner, Properties and go to the Compatibility Tab and check the box "Run this program as an admin".
 

Nope.

Put a pause at the end of the bat file and see what error its throwing then you can work from there.