Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[ArmenianCracker]

Hi there, i woud like to know did the author of this program planing to add optimized timings for AMD Radeon VII, if yes then when approximatly???Thanks

I could be woefully wrong about this, but I thought Radeon VII was core limited not memory limited. If this is the case, optimized memory timings won't help.

I thought Radeon VII's were already getting 90MH/s with just a refresh rate tweak.  I could also be wrong, but there are a few users over in the AMDTweakTool thread that have them.  Check there.

I'm already getting about 90MH/s with nothing more than AMD Afterburner tweaks. 

I am geting 90MH/S +- 1-2MH/S on my Radeon VII too with HBM2 memory from Hynix with 956mv/CLK 1750mhz mem 1200mhz, but i think when -strape function will work on Redeon VII we can get more maybe 95 or 96mh/s on Etherium.
[/quote]

[quejo]

and for me it was so. the solution for me: open windows  powershell (administrator)  you enter :  " bcdedit -set TESTSIGNING off ".this deactivates the test mode. restart the computer and start claymore.the program shows a red sign that it is not in test mode and restarts again. it should be fine now

worked once. asa a reboot was made hashrate dropped from 375 to 320. Already tried everything. When claymore tries to install driver after disabling test mode windows pops up a warning about unsigned driver installation. After reboot windows start in test mode so its supposed that driver was successfully installed but then the same hashrate.

heres my config file

-asm 2
-gser 1
-tt 60
-ttli 65
-wd 0
-cclock 1150
-y 1
-mode 1
-dbg -1
-powlim 20
-strap 5@2040,1@1900,1@1750,5@2000,1@1750,1@2000,1@1930,5@2000,2@1850,1@1850,1@1750,1@1900,1@2000
-rxboost 1
-cvddc 875,875,875,875,875,900,875,900,850,875,850,800,875
-mvddc 875,875,875,875,875,900,875,900,850,875,850,800,875

when i found that voltages values i figured out that somehow core voltage and memory voltage were linked so if i decrease core without also decreasing memory voltage it wont work. do you face the same behavior?

[defoto]

-epsw x -asm 2 -mode 1 -rxboost 1 -esm 3  -allpools 1 -estale 0 -strap POL8H2,POL8M2,POL8M2,POL8S1,POL8S1,POL8S1,POL8S1,POL8M2  -cclock 1250,1250,1250,1250,1250,1250,1250,1250 -cvddc 900,900,900,900,900,900,900,900 -mclock 2230,2230,2230,2150,2180,2180,2140,2230 -mvddc 900,900,900,900,900,900,900,900 -tt 62 -fanmin 0 -fanmax 70      this is 8 rx580 8gb - 266.7 mh/s  ,1200 w

[Xazax310]

Hello all, I recently acquired a bunch of RX470s and was hoping to use Claymores 14.6 STRAPs but no luck. I need some help.
When I use -STRAP option the miner will apply STRAP 1 to GPU 0, then GPU 1, then the computer crashes and restarts. Everytime it doesnt matter what I do, voltages etc.

If I apply the STRAP to only GPU 0 it will work fine, however, if I apply it to GPU 1, 2, 3 etc even one other GPU instant crash and Windows reboots.

I'm at a total loss of what's causing it.

The miner works perfectly normal as long as I avoid the STRAP option. RXBOOST works perfectly fine.  

Seeking help or ideas!

Rig
13 RX470s
H110 Pro BTC+
G3930, 4GB RAM, 450w PSU
2400w DELTA PSU for cards
Windows 1903 Build(May release)
AMD 19.5.1 drivers

[dormancygrace]

Hi!  Can you make double memory kernels for gpus with enough ram?  Like it is done in PhoenixMiner?

[bperryman]

Is there any chance that you could tweak your Blake2b algorithm to allow for GlobalToken and TitleNetwork variants? I know they're very similar to old Sia.

[ngohungvi]

Can current graphics cards with 3G Vram mine ETH? (GTX 1060 3G , p106-090 3G,v.v...)
Thank you.

[Dr_Victor]

Can current graphics cards with 3G Vram mine ETH? (GTX 1060 3G , p106-090 3G,v.v...)
Thank you.

Unfortunately, no

[Xazax310]

Can current graphics cards with 3G Vram mine ETH? (GTX 1060 3G , p106-090 3G,v.v...)
Thank you.

No, ETH/ETC are over the 3GB DAG limit and can never mine ETH again. You can try other lower dag coins like CLO,UBQ,EXP, etc

[cryptomaxsun]

For mining Ethereum with the 480 card, which driver is better to use and which hashrate should be?

[Dr_Victor]

For mining Ethereum with the 480 card, which driver is better to use and which hashrate should be?

You can use the latest Adrenalin 2019 and get 31-33-35Mh.

[arianx]

tnx guys
now i get 33.3 per card
http://uupload.ir/files/5ztj_sgdsgd.jpg

[paceemail]

If I am understanding correctly people are seeing best results with the following for RX570/580

RXboost -1 and strap -1
Increase Core to around 1180,  memory at around 2050-2100
DDU and install latest AMD drivers

The last one is what I want to confirm as I am using 18.3.1? for some time and haven't had issues, so wanted to confirm before I DDU and reinstall on all rigs. Also I saw some mentions of 20GB virtual, I usually run 16 Minimum, did I miss something in release notes about upping this?

Thanks!

[lolzminer]

i have  a question i cant run the noromal batch file in admin since this new windows update where as before i could include -strap 1 and it would apply straps etc but now only way i caN ACTIVATE THE STRAPS IS WHEN I INSTALL THE DRIVER -DRIVER INSTALL OR JUST -STRAP 1 ON THE SECOND LAUNCHER THE 1 U HAVE TO RIGHT CLICK AND RUN AS ADMIN. but if i uninstall it so it comes out of test mode soon as i run normla the second launcher and i put -strap 1 it puts my minerback into test mode ? is it  abug or am i doing somethign wrong. ethereum miner claymore 14.6 and it wont allow me to apply the -rxboost 1 as it wont work without admin rights.

[quejo]

tnx guys
now i get 33.3 per card
http://uupload.ir/files/5ztj_sgdsgd.jpg

What cards and settings are you using?
Are you monitoring errors with hwinfo?

[arianx]

tnx guys
now i get 33.3 per card
http://uupload.ir/files/5ztj_sgdsgd.jpg

What cards and settings are you using?
Are you monitoring errors with hwinfo?

Rx580 SP
no errors

[MATHReX]

tnx guys
now i get 33.3 per card

Is it stable?
I have hynix memory RX580 cards.
Even at best settings, I'm getting  32MH/s per card but they are unstable, crashes after an hour or two.

[cryptomaxsun]

For mining Ethereum with the 480 card, which driver is better to use and which hashrate should be?

You can use the latest Adrenalin 2019 and get 31-33-35Mh.

what's wrong ? followed the advice and only 12 mh.
on the forks of ethereum 29 mh.

[Jonet]

i have  a question i cant run the noromal batch file in admin since this new windows update where as before i could include -strap 1 and it would apply straps etc but now only way i caN ACTIVATE THE STRAPS IS WHEN I INSTALL THE DRIVER -DRIVER INSTALL OR JUST -STRAP 1 ON THE SECOND LAUNCHER THE 1 U HAVE TO RIGHT CLICK AND RUN AS ADMIN. but if i uninstall it so it comes out of test mode soon as i run normla the second launcher and i put -strap 1 it puts my minerback into test mode ? is it  abug or am i doing somethign wrong. ethereum miner claymore 14.6 and it wont allow me to apply the -rxboost 1 as it wont work without admin rights.

Windows has to be in test mode because the driver is not signed. If you uninstall the driver to get windows out of test mode you cannot use -strap or -rxboost. You don't have to run the normal batch file with admin rights, only when you install/uninstall driver or set AMD driver to compute (y).

[fredeq]

For mining Ethereum with the 480 card, which driver is better to use and which hashrate should be?

You can use the latest Adrenalin 2019 and get 31-33-35Mh.

what's wrong ? followed the advice and only 12 mh.
on the forks of ethereum 29 mh.

Check -y setting to enable compute mode