AMD Mem Tweak XL - Read/modify timings/pp/straps on the fly

[livada]

vega 56-hynix
i use this setup
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600
work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(

what i must chage? what step i must use?
etc: rp14 to rp15
rfc 156 chg to rfc 157 ? or i must use 168 or higher?

what step use ? 1? or nubmer /with 8 or 16?

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...


i try down mem 1100 to 1090mhz but again have error
i try give more  power. now work with 870mv and i try with 920mv but again have error

pls any tutotrial what formula work with rp rc rfc ref  etc....

read back a little for formulas

if your hynix memclk is really 1100 then and it's stable at stock timings, then rfc and rc and rcdwr are too low imho.

i read all page but not see any forumula..(i go read again)

my mistake- 1100 for samsung. 1 samsung card always have error 1100 or 1090 .

[doktor83]

vega 56-hynix
i use this setup
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600
work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(

what i must chage? what step i must use?
etc: rp14 to rp15
rfc 156 chg to rfc 157 ? or i must use 168 or higher?

what step use ? 1? or nubmer /with 8 or 16?

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...


i try down mem 1100 to 1090mhz but again have error
i try give more  power. now work with 870mv and i try with 920mv but again have error

pls any tutotrial what formula work with rp rc rfc ref  etc....

read back a little for formulas

if your hynix memclk is really 1100 then and it's stable at stock timings, then rfc and rc and rcdwr are too low imho.

i read all page but not see any forumula..(i go read again)

my mistake- 1100 for samsung. 1 samsung card always have error 1100 or 1090 .

Ram timings in nutshell

[livada]

vega 56-hynix
i use this setup
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600
work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(

what i must chage? what step i must use?
etc: rp14 to rp15
rfc 156 chg to rfc 157 ? or i must use 168 or higher?

what step use ? 1? or nubmer /with 8 or 16?

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...


i try down mem 1100 to 1090mhz but again have error
i try give more  power. now work with 870mv and i try with 920mv but again have error

pls any tutotrial what formula work with rp rc rfc ref  etc....

read back a little for formulas

if your hynix memclk is really 1100 then and it's stable at stock timings, then rfc and rc and rcdwr are too low imho.

i read all page but not see any forumula..(i go read again)

my mistake- 1100 for samsung. 1 samsung card always have error 1100 or 1090 .

Ram timings in nutshell

thx.
i read this but this is to high for me.

i need tutorial for noob  not for expert.
like if use 1+ CL you must chg RP +12 etc.

just some basics- my mem timinig work and i must chg little down . i have only 2-3 error in 12 hour

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600

what fisrst try chg? RP? REF? with   step . 1?

[pbfarmer]

hey farmer, are you still using ppt at all?  the ones from the past?

Hey what’s up...  Always using PPTs, but I roll my own...  I’m also mostly on Linux now, and only use ppt to set clocks/voltages/fans (no other profile tools,) so they change based on the algo im mining.

Cnr/cnv4 is similar to cnv2, but I’ve been on trtl lately using ethash-like settings

[Zorg33]

what fisrst try chg? RP? REF? with   step . 1?

I did paste a picture from wikipedia with formulas.

[SigiSinatra]

I can't start GUI version at all.
I double click on .exe and nothing happens.

Version 0.1.7 worked and now it won't. Does .net framework (required for gui) maybe affects it ?
I was getting 2400 h/s with vega 64 and 2200 h/s on vega 56 (64 bios) with Teamredminer.
After restart it simply won't. I tried to run it as admin and without and still nothing.

Also, when I type winamdtweak.exe --current console just flash for sec and disappears. I tried with cmd /k but it doesn't work.
If I try to run CMD as an administrator I get failed to load EIO.dll

Any solutions?  
Thank you

Use full path

"C:\PathtoAmdMemTweak\winamdtweak.exe --curren"
pause?
And run as admin ...

I tried, but if I run it as as admin 'failed to load/find EIO.dll' message appears. (I have EIO.dll)
It worked first time, but after I tried new GUI version and restarted PC it simply won't work.

[Mashy81]

vega 56-hynix
i use this setup
--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600
work 10-12 hour with 2-3 error and block all comp and dont go tu restart:(

what i must chage? what step i must use?
etc: rp14 to rp15
rfc 156 chg to rfc 157 ? or i must use 168 or higher?

what step use ? 1? or nubmer /with 8 or 16?

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600 - work but i must little downclock this, but i dont know how and what...


i try down mem 1100 to 1090mhz but again have error
i try give more  power. now work with 870mv and i try with 920mv but again have error

pls any tutotrial what formula work with rp rc rfc ref  etc....

read back a little for formulas

if your hynix memclk is really 1100 then and it's stable at stock timings, then rfc and rc and rcdwr are too low imho.

i read all page but not see any forumula..(i go read again)

my mistake- 1100 for samsung. 1 samsung card always have error 1100 or 1090 .

Ram timings in nutshell

thx.
i read this but this is to high for me.

i need tutorial for noob  not for expert.
like if use 1+ CL you must chg RP +12 etc.

just some basics- my mem timinig work and i must chg little down . i have only 2-3 error in 12 hour

--rp 14 --rc 42 --rfc 156 --rrds 4 --rrdl 5 --rrd 3 --rcdrd 18 --rcdwr 3 --REF 15600

what fisrst try chg? RP? REF? with  step . 1?

Try higher rfc. I run 208 and 260 on my vegas and add --ras 46 maybe

[HeueysaJuaust]

Windows gui not working. I tried windows 10 64bit 1803-1809 and Adrenalin 19.04.1 and blockchain amd drivers
Double click tweak and nothing happens.

[Bojcha]

Windows gui not working. I tried windows 10 64bit 1803-1809 and Adrenalin 19.04.1 and blockchain amd drivers
Double click tweak and nothing happens.

You need to enable netframework 3.5 in windows.
Control panel > Turn windows features on or off.

[HeueysaJuaust]

Windows gui not working. I tried windows 10 64bit 1803-1809 and Adrenalin 19.04.1 and blockchain amd drivers
Double click tweak and nothing happens.

You need to enable netframework 3.5 in windows.
Control panel > Turn windows features on or off.

I know. Enabled. But not working tweak.

if netframework disable, program showing error message.

[Eliovp]

Check releases guys, in case it's not opening, there's another version.

Working on a newer release with upgrades and fixes to potential issues.

Here's the link to a working version: Link

[nordmann666]

someone could enable powertemp with newer drivers? thats the reason i cant use the new drivers cause i have to set pwertemp limit for some cards that get´s to hot

[dingdongtobias]

who help me use with any polaris gpu, i change ANYTHING in gui tweak got rig crash if not crash nothing happen ??

run under work, when miner working.

same gpu clock/setting sometime tweak read one values then sometime other. is this working on gddr5 memory??

[kerney666]

someone could enable powertemp with newer drivers? thats the reason i cant use the new drivers cause i have to set pwertemp limit for some cards that get´s to hot

Afaik it’s fan curve only, and the implementation is so effing broken. I haven’t checked 19.4.x, but earlier versions don’t interpolate between states, it just switches hard. It’s ridiculous on my Radeon VII with a very aggressive ramp up to 100%.

[SigiSinatra]

someone could enable powertemp with newer drivers? thats the reason i cant use the new drivers cause i have to set pwertemp limit for some cards that get´s to hot

If you're using adrenaline 19 you will need to use PPT generator and set power temp manually in reg file.

[kerney666]

someone could enable powertemp with newer drivers? thats the reason i cant use the new drivers cause i have to set pwertemp limit for some cards that get´s to hot

If you're using adrenaline 19 you will need to use PPT generator and set power temp manually in reg file.

Have you confirmed it’s working yourself? I’ve seen reports from people trying exactly that with no effect.

[cscheat]

hey guys,

How come i can't set the VDDC lower than 900mv? seems like stuck at 900 lowest

[HansHagberg]

Tried latest Win version (_x64). Activated .NET etc.
Application terminates immediately without any sign if error messages, log messages or anything.

[ingyenfrag]

hey guys,

How come i can't set the VDDC lower than 900mv? seems like stuck at 900 lowest

For vega, proper PPT needed...

Here is mine--->https://drive.google.com/open?id=1OvKJbv7psAO59I8EavFH5704wf7sr_9z

GPU P7 830MHz/ HBM P3 850MHz -->  0.825V
GPU P7 850MHz/ HBM P3 860Mhz --> 0.8375V
GPU P7 850MHz/ HBM P3 880MHz --> 0.85V

[livada]

Try higher rfc. I run 208 and 260 on my vegas and add --ras 46 maybe

thx

hey guys,

How come i can't set the VDDC lower than 900mv? seems like stuck at 900 lowest

For vega, proper PPT needed...

Here is mine--->https://drive.google.com/open?id=1OvKJbv7psAO59I8EavFH5704wf7sr_9z

GPU P7 830MHz/ HBM P3 850MHz -->  0.825V
GPU P7 850MHz/ HBM P3 860Mhz --> 0.8375V
GPU P7 850MHz/ HBM P3 880MHz --> 0.85V

what vega?56/64? samsung/hynix?