PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[chschlumpf]

Hello
I needed to install the drivers new. I use -amd. I use RX480, blockchain driver and 3.0c. Stopped working last friday.

FATAL ERROR: Debugger detected

What can I do? Claymore is working.
Thx for helping

[jimsta]

I had the same issues, this past week.. the 3.0 versions gave my 2 rigs massive problems.  It just wouldn't start and kept crashing.

I've switched back to 2.9 on 2 rigs and claymore on my nvidia mining rig (nvidia on phoenix kept locking up the rig).

Hello
I needed to install the drivers new. I use -amd. I use RX480, blockchain driver and 3.0c. Stopped working last friday.

FATAL ERROR: Debugger detected

What can I do? Claymore is working.
Thx for helping

[Tienlv]

HI ANYBODY help me >this my erro 1050ti 4G. how can i fix them ? thanks
GPU8 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.876: GPU1 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.878: GPU1 GPU1 search error: unspecified launch failure
2018.07.09:08:38:32.879: GPU8 GPU8 search error: unspecified launch failure
2018.07.09:08:38:32.888: GPU4 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.888: GPU4 GPU4 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU5 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU3 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU3 GPU3 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU5 GPU5 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU7 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU7 GPU7 search error: unspecified launch failure
2018.07.09:08:38:32.890: GPU6 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.890: GPU6 GPU6 search error: unspecified launch failure
2018.07.09:08:38:32.953: GPU2 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.953: GPU2 GPU2 search error: unspecified launch failure
2018.07.09:08:38:33.234: wdog Thread(s) not responding. Restarting.

[j2james]

HI ANYBODY help me >this my erro 1050ti 4G. how can i fix them ? thanks
GPU8 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.876: GPU1 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.878: GPU1 GPU1 search error: unspecified launch failure
2018.07.09:08:38:32.879: GPU8 GPU8 search error: unspecified launch failure
2018.07.09:08:38:32.888: GPU4 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.888: GPU4 GPU4 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU5 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU3 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU3 GPU3 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU5 GPU5 search error: unspecified launch failure
2018.07.09:08:38:32.889: GPU7 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.889: GPU7 GPU7 search error: unspecified launch failure
2018.07.09:08:38:32.890: GPU6 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.890: GPU6 GPU6 search error: unspecified launch failure
2018.07.09:08:38:32.953: GPU2 CUDA error in CudaProgram.cu:329 : unspecified launch failure (719)
2018.07.09:08:38:32.953: GPU2 GPU2 search error: unspecified launch failure
2018.07.09:08:38:33.234: wdog Thread(s) not responding. Restarting.

Typically this is a problem of over overclocking of memory. Try to decrease it. I had this error many times while I did not decrease memory overclocking.

[chillyray]

Hey I got this issue where Phoenix just stops forever (doesn't freeze rig) at the point where it *should* list out all the detected graphics cards.

Thing is I have 4 rigs all the same base hardware, cloned drives and 3/4 of them run Phoenix 3.0c without any issue the one of them just stops at that listing GC point.
The only differences between rigs is the brand of graphics cards:
1. All Sapphire RX580 8gb - No problem
2. Mix of MSI & Sapphire RX580 8Gb - No problem
3. Mix of Sapphire RX580 4Gb & Nvidia - No problem
4. All MSI RX580 8gb - Halts at Phoenix prompt detecting graphics cards, no output, waited 30mins nothing?

And also all 4 rigs had been previously running claymore for around a year without any issue. The MSI rig will run up claymore without issue *but* after an attempted Phoenix run it will not work, I have to first reboot the rig.

So its something to do with Pheonix + the GC bios' in that rig?

Anyone seen this issue?
How can I get more (than nothing) diagnostics output?


Thanks!

Edit:
btw this is the only thing in the log:

2018.07.10:12:26:40.888: main Phoenix Miner 3.0c Windows/msvc - Release
2018.07.10:12:26:40.888: main Cmd line: -pool stratum+tcp://connect.ubiqminers.com:3004 -wal 0x55a742880e846549aED7f147dbFe24e7A0eA075e.rig1 -proto 4 -amd

[MaxMidnite]

I'm having a problem with the latest version.
6 x RX580 cards, all is well for a few hours, then my machine seems to freeze.
I need to do hardreset to get it to work again, I'm not sure what the problem is.
On my other 2x Nvidea 1070ti machine there no issues and runs for days.
I do not think its overclock but not sure.

Whats the best way to see what the problem is?

[digitalunix]

I'm having a problem with the latest version.
6 x RX580 cards, all is well for a few hours, then my machine seems to freeze.
I need to do hardreset to get it to work again, I'm not sure what the problem is.
On my other 2x Nvidea 1070ti machine there no issues and runs for days.
I do not think its overclock but not sure.

Whats the best way to see what the problem is?

check sleep and wake up functions... it seems something like that.

[stiucsib86]

Hey dude, I figured it out on my rig. I uninstalled the drivers for the iGPU. Once I did that, I got video output from one of the graphics cards and it let me start mining just fine.

https://www.reddit.com/r/EtherMining/comments/8p71di/claymore_and_phoenix_both_will_not_start_details/e0a65nc/

Putting this link here just incase anyone else having issue starting PhoenixMiner (or Claymore) after the recent Windows update.

[janding]

This miner fucks out on cuda

Hey dude.
From your posts I am convinced you don't have the brain to handle something like a miner.
You come across as a moron, and I believe it.
You should not mine,  try ping-pong or something that doesn't require intelligence.
I seriously doubt you know which end of a video card to plug into a computer.

Hope these words weren't too big for you, I tried to keep it simple.
Have someone read this to you.

[DXInfinity]

Version 3.0c. Fan control seems not to be working properly.
Environment:
Clean installation Windows 10 (1709), no updates.
Drivers - latest (18.6.1)
Card: single Asus ROG Strix RX580 O8G (stock bios, only timings modified)
No any additional software than can interfere with fan control is installed (like Afterburner etc.)

-fanmin 50
-fanmax 100
-tt 55

When miner starts - fans are initially stopped. When temperature rises to 50 and above - fans start working on max speed (maybe not max but high enough). In a few seconds temperature drops below 50 and fans begin to slowdown and finally stop. In a few seconds the sequence repeats.

Tried setting -tt -50 to force constant fan speed - not working.

At the same time it works on Asus Strix RX570 more or less properly. At least asjusts fan speed to keep temperature set by -tt.
I have compared bios bios fan settings for these two cards - they are identical.
It is incompatibility with this particular card or I am missing something?

[human75]

 
Cannot say more:-)

This miner fucks out on cuda

Hey dude.
From your posts I am convinced you don't have the brain to handle something like a miner.
You come across as a moron, and I believe it.
You should not mine,  try ping-pong or something that doesn't require intelligence.
I seriously doubt you know which end of a video card to plug into a computer.

Hope these words weren't too big for you, I tried to keep it simple.
Have someone read this to you.

[MaxMidnite]

I'm having a problem with the latest version.
6 x RX580 cards, all is well for a few hours, then my machine seems to freeze.
I need to do hardreset to get it to work again, I'm not sure what the problem is.
On my other 2x Nvidea 1070ti machine there no issues and runs for days.
I do not think its overclock but not sure.

Whats the best way to see what the problem is?

check sleep and wake up functions... it seems something like that.

I found in windows logs, issue is to do with amddiag or sumfin. quit unexpectedly.
I was using latest amd drivers so now gone downgrade..
Whats most best drivers?

[Exit_left]

I'm having a problem with the latest version.
6 x RX580 cards, all is well for a few hours, then my machine seems to freeze.
I need to do hardreset to get it to work again, I'm not sure what the problem is.
On my other 2x Nvidea 1070ti machine there no issues and runs for days.
I do not think its overclock but not sure.

Whats the best way to see what the problem is?

check sleep and wake up functions... it seems something like that.

I found in windows logs, issue is to do with amddiag or sumfin. quit unexpectedly.
I was using latest amd drivers so now gone downgrade..
Whats most best drivers?

I've been mining very stably for 2 months on 18.3.4, after having nothing but trouble on blockchain beta drivers.

[damba_]

Version 3.0c. Fan control seems not to be working properly.
Environment:
Clean installation Windows 10 (1709), no updates.
Drivers - latest (18.6.1)
Card: single Asus ROG Strix RX580 O8G (stock bios, only timings modified)
No any additional software than can interfere with fan control is installed (like Afterburner etc.)

-fanmin 50
-fanmax 100
-tt 55

When miner starts - fans are initially stopped. When temperature rises to 50 and above - fans start working on max speed (maybe not max but high enough). In a few seconds temperature drops below 50 and fans begin to slowdown and finally stop. In a few seconds the sequence repeats.

Tried setting -tt -50 to force constant fan speed - not working.

At the same time it works on Asus Strix RX570 more or less properly. At least asjusts fan speed to keep temperature set by -tt.
I have compared bios bios fan settings for these two cards - they are identical.
It is incompatibility with this particular card or I am missing something?

Have you tried control fan speed using any other software, e.g. Asus gpu tweak II?
Command -tt -50 should keep fans at 50% but that GPU has a thing they called 0dB technology and it starts fans at 55°C and stops them when temperature drops below that value.
Maybe you should try -tt -30 to keep fans at 30%, that way GPU should be above 55°C and fans would be spinning constantly.

[Exit_left]

Have you tried control fan speed using any other software, e.g. Asus gpu tweak II?
Command -tt -50 should keep fans at 50% but that GPU has a thing they called 0dB technology and it starts fans at 55°C and stops them when temperature drops below that value.
Maybe you should try -tt -30 to keep fans at 30%, that way GPU should be above 55°C and fans would be spinning constantly.

I don't think that's right.  -tt should be target temp, right?  As in, the miner will adjust the fans to keep the temp at the -tt value.  The args to do what you're suggesting should be -fanmin 30.  Or am I an idiot?

[damba_]

Have you tried control fan speed using any other software, e.g. Asus gpu tweak II?
Command -tt -50 should keep fans at 50% but that GPU has a thing they called 0dB technology and it starts fans at 55°C and stops them when temperature drops below that value.
Maybe you should try -tt -30 to keep fans at 30%, that way GPU should be above 55°C and fans would be spinning constantly.

I don't think that's right.  -tt should be target temp, right?  As in, the miner will adjust the fans to keep the temp at the -tt value.  The args to do what you're suggesting should be -fanmin 30.  Or am I an idiot?

I just checked readme file and it says:
-tt <n> Set fan control target temperature (special values: 0 - no HW monitoring on ALL cards,
     1-4 - only monitoring on all cards with 30-120 seconds interval, negative - fixed fan speed at n %)

That means if you set -tt 30 that target temperature should be 30°C (I am just using this temperature as an example), but if you set -tt -30 that means you set fixed fan speed at 30%.
I am using -tt -70 in Claymore miner and my fans are constantly spinning at 70%, it should do the same in PhoenixMiner.
Try -tt -30 or some other value and see what happens.

[Exit_left]

Have you tried control fan speed using any other software, e.g. Asus gpu tweak II?
Command -tt -50 should keep fans at 50% but that GPU has a thing they called 0dB technology and it starts fans at 55°C and stops them when temperature drops below that value.
Maybe you should try -tt -30 to keep fans at 30%, that way GPU should be above 55°C and fans would be spinning constantly.

I don't think that's right.  -tt should be target temp, right?  As in, the miner will adjust the fans to keep the temp at the -tt value.  The args to do what you're suggesting should be -fanmin 30.  Or am I an idiot?

I just checked readme file and it says:
-tt <n> Set fan control target temperature (special values: 0 - no HW monitoring on ALL cards,
     1-4 - only monitoring on all cards with 30-120 seconds interval, negative - fixed fan speed at n %)

That means if you set -tt 30 that target temperature should be 30°C (I am just using this temperature as an example), but if you set -tt -30 that means you set fixed fan speed at 30%.
I am using -tt -70 in Claymore miner and my fans are constantly spinning at 70%, it should do the same in PhoenixMiner.
Try -tt -30 or some other value and see what happens.

Ah ok, I see.  Thanks for clarifying!

[rongphuongnam]

Hello Phoenix team,

Any update? I seem version 3.0C have some problem, a lot of PP rollback 2.9e

[B00gieman]

No problem here.

[mrpcrp]

OhGodAnETHlargementPill work only for DDR5x memory cards - 1080 and 1080ti
1060 and 1070 dont increase hashrate by it