SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching

[just4u]

I never really thought about flashing these cards (had them over a year now..) reports were it was "iffy" on Asus Strix cards that don't use Samsung mem.   I tend to switch between Xmrig, Stak, SRB, if mining xmr.. plus dok has low fees and works on his a lot.

Hi, with SRB your best drivers would be 18.6.1 with CN/R, because on every new block from the pool, the kernel is recompiled and my tests show that 18.6.1 compiles the best code still.
I know there are users here who have Hynix mem Vegas and were able to get nice results, maybe they can help you out. I have only 1 Vega56 with Hynix mem but it is a really good piece, it goes on profile 10 without problems and 2100+ hash.

112/16/2 are the best settings you can get for CN/R. Maybe try out the low profiles (add L after the profile number)
If using config file, you must surround the value with quotation marks if you want to use the L profile. Example : "5L"

Thanks for the kind words, and for using SRB.

Yeah, I used to use the 18.6.1s but so hard now with the way you can configure wattman for so many different usage scenarios.  I'll look into the Lowprofile stuff. Thanks Dok.

[404_not_found]

I never really thought about flashing these cards (had them over a year now..) reports were it was "iffy" on Asus Strix cards that don't use Samsung mem.   I tend to switch between Xmrig, Stak, SRB, if mining xmr.. plus dok has low fees and works on his a lot.

Hi, with SRB your best drivers would be 18.6.1 with CN/R, because on every new block from the pool, the kernel is recompiled and my tests show that 18.6.1 compiles the best code still.
I know there are users here who have Hynix mem Vegas and were able to get nice results, maybe they can help you out. I have only 1 Vega56 with Hynix mem but it is a really good piece, it goes on profile 10 without problems and 2100+ hash.

112/16/2 are the best settings you can get for CN/R. Maybe try out the low profiles (add L after the profile number)
If using config file, you must surround the value with quotation marks if you want to use the L profile. Example : "5L"

Thanks for the kind words, and for using SRB.

Dok, what are your profile settings in ODT allowing for 2100+ using profile 10? Can barely push 2000+ on profile 7 – "8L" is a no-go. Much appreciated.

[doktor83]

I never really thought about flashing these cards (had them over a year now..) reports were it was "iffy" on Asus Strix cards that don't use Samsung mem.   I tend to switch between Xmrig, Stak, SRB, if mining xmr.. plus dok has low fees and works on his a lot.

Hi, with SRB your best drivers would be 18.6.1 with CN/R, because on every new block from the pool, the kernel is recompiled and my tests show that 18.6.1 compiles the best code still.
I know there are users here who have Hynix mem Vegas and were able to get nice results, maybe they can help you out. I have only 1 Vega56 with Hynix mem but it is a really good piece, it goes on profile 10 without problems and 2100+ hash.

112/16/2 are the best settings you can get for CN/R. Maybe try out the low profiles (add L after the profile number)
If using config file, you must surround the value with quotation marks if you want to use the L profile. Example : "5L"

Thanks for the kind words, and for using SRB.

Dok, what are your profile settings in ODT allowing for 2100+ using profile 10? Can barely push 2000+ on profile 7 – "8L" is a no-go. Much appreciated.

I guess its more about the asic quality and cooling, than settings.
ODT is nothing special : 1450/940 900mV

[logicalray77]

mind sharing your results on RX580 CN GPU hash rates please and your configs.

[404_not_found]

I never really thought about flashing these cards (had them over a year now..) reports were it was "iffy" on Asus Strix cards that don't use Samsung mem.   I tend to switch between Xmrig, Stak, SRB, if mining xmr.. plus dok has low fees and works on his a lot.

Hi, with SRB your best drivers would be 18.6.1 with CN/R, because on every new block from the pool, the kernel is recompiled and my tests show that 18.6.1 compiles the best code still.
I know there are users here who have Hynix mem Vegas and were able to get nice results, maybe they can help you out. I have only 1 Vega56 with Hynix mem but it is a really good piece, it goes on profile 10 without problems and 2100+ hash.

112/16/2 are the best settings you can get for CN/R. Maybe try out the low profiles (add L after the profile number)
If using config file, you must surround the value with quotation marks if you want to use the L profile. Example : "5L"

Thanks for the kind words, and for using SRB.

Dok, what are your profile settings in ODT allowing for 2100+ using profile 10? Can barely push 2000+ on profile 7 – "8L" is a no-go. Much appreciated.

I guess its more about the asic quality and cooling, than settings.
ODT is nothing special : 1450/940 900mV

For sure. And yeah, ODT nearly identical. Figured to cross-reference with your settings. Cheers.

[doktor83]

V1.9.3
- Fixed CN-Gpu algo compilation on RX 5700 and older GCN cards
- Improved CN-Gpu algo on Rx550/560 , Rx470/480/570/580/590
- 4gb Ellesmere cards got a small hashrate increase on CN-Conceal algo

+ Did a blind fix for RX 5700 on CN-GPU algo, it should now compile but i don't know what's the hashrate and will it spit valid shares at all  

+ CN-GPU algo got some love, especially on RX550/560 4g cards (tested on auto settings) + 20% hashrate increase in my tests for these cards

+ CN-Conceal also got small boost on 4g ellesmere cards

[ronnieb]

V1.9.3
- Fixed CN-Gpu algo compilation on RX 5700 and older GCN cards
- Improved CN-Gpu algo on Rx550/560 , Rx470/480/570/580/590
- 4gb Ellesmere cards got a small hashrate increase on CN-Conceal algo

+ Did a blind fix for RX 5700 on CN-GPU algo, it should now compile but i don't know what's the hashrate and will it spit valid shares at all 

+ CN-GPU algo got some love, especially on RX550/560 4g cards (tested on auto settings) + 20% hashrate increase in my tests

+ CN-Conceal also got small boost on 4g ellesmere cards

Ill try my 5700 gpu when i get home from work.

[doktor83]

V1.9.3
- Fixed CN-Gpu algo compilation on RX 5700 and older GCN cards
- Improved CN-Gpu algo on Rx550/560 , Rx470/480/570/580/590
- 4gb Ellesmere cards got a small hashrate increase on CN-Conceal algo

+ Did a blind fix for RX 5700 on CN-GPU algo, it should now compile but i don't know what's the hashrate and will it spit valid shares at all 

+ CN-GPU algo got some love, especially on RX550/560 4g cards (tested on auto settings) + 20% hashrate increase in my tests

+ CN-Conceal also got small boost on 4g ellesmere cards

Ill try my 5700 gpu when i get home from work.

Thanks, i am also interested in other algo results ( if it compiles ).
Auto settings are probably bad for every algo, so if you are in an adventurous mood you can try different intensity/worksize/fragment settings

[darkminesys]

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

https://i.imgur.com/nu7kjcS.png

[doktor83]

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

wow.. i will stop doing blind fixes until i get a card.. just time wasting.
when i do an offline compile on amd driver v19.7.1 for gfx1010 it all goes smooth. So i really don't understand why it won't work on a 'live' card.

Really nice driver, this one is also reporting the number of CU's wrong 

Thanks for reporting

[hesido]

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

wow.. i will stop doing blind fixes until i get a card.. just time wasting.
when i do an offline compile on amd driver v19.7.1 for gfx1010 it all goes smooth. So i really don't understand why it won't work on a 'live' card.

Really nice driver, this one is also reporting the number of CU's wrong  

Thanks for reporting

For 5700, AMD may be intentionally making miner use worse. PhoenixMiner is having problems creating an optimized eth miner for it for this reason.

Does SRB Miner work good for rx580's with the latest drivers? For example does fan control work etc?

[cikusa]

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

wow.. i will stop doing blind fixes until i get a card.. just time wasting.
when i do an offline compile on amd driver v19.7.1 for gfx1010 it all goes smooth. So i really don't understand why it won't work on a 'live' card.

Really nice driver, this one is also reporting the number of CU's wrong 

Thanks for reporting

Got myself a card today, tried it on 5700xt same error, it is quite hard to get it in Serbia

[burntroach85]

PhoenixMiner is having problems because claymore hasnt released it yet LOL   

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

wow.. i will stop doing blind fixes until i get a card.. just time wasting.
when i do an offline compile on amd driver v19.7.1 for gfx1010 it all goes smooth. So i really don't understand why it won't work on a 'live' card.

Really nice driver, this one is also reporting the number of CU's wrong  

Thanks for reporting

For 5700, AMD may be intentionally making miner use worse. PhoenixMiner is having problems creating an optimized eth miner for it for this reason.

Does SRB Miner work good for rx580's with the latest drivers? For example does fan control work etc?

[masterloka1]

autoptimize options amd + nvdia  = %15 fasted thank you bro.

https://www.dosyaupload.com/rvZP

[Elder III]

Appreciate all the effort going into this, dok. I'm sure the 5700 drivers aren't helping matters at all yet.

I have the same error message on my 5700 XT.

Enumerating OpenCL devices, please wait...

GPU0: AMD Radeon RX 5700 XT [gfx1010] [8176 MB][CU: 20][I: 71.0][W: 16][T: 2][F: 8][BUS: 14]

---------------------------------------------------------------------------------------------
SRBMiner Cryptonight AMD GPU miner 1.9.3
DevFee ~0.85%

Press 's' to display stats
Press 'h' to display hashrate
Press 'r' to reload pools
Press 'p' to switch to the next pool
Press 'o' to switch to the previous pool
Press 0-9 to disable/enable GPU 0-9, shift+0-9 for GPU 10-19
---------------------------------------------------------------------------------------------

Algorithm               : Cryptonight V4 (CN/R)
Algo switching          : disabled
Coin forking            : disabled
Gpu watchdog            : enabled [normal mode]
Startup monitor         : enabled
Tweaking                : disabled


[2019-07-23 23:28:23] Pools defined -> 2
[2019-07-23 23:28:23] Please run miner as administrator to enable tweaking
[2019-07-23 23:28:24] Compiling [normalv4] kernel for DEVICE BUS_ID[14]
error: <unknown>:0:0: in function cn0 void (<4 x i32> addrspace(1)*, i64 addrspace(1)*, i32, i64 addrspace(4)*): unsupported indirect call to function doKeccak

Press any key to continue . . .

[Turkish88]

Who can advise what is the best coin for now on cryptonight to mining with 2gb rx 550 gpu's
i am dropped from mining for last half year

[cas333]

Hi dok,
Today Loki forking to RandomXL algo. Can you please check and add it for mining? Or you dont have intention to touch RandomX algo?

[hesido]

OverdriveNTool fan control does not seem to work with the new AMD drivers, any workarounds?
Edit: Trying the Latest OverdriverNTool now, I guess there's hope. I wish SRB supports native gpu freq/voltage/fan control in future! When new algo madness resolves itself, may dok can lean on that.

[doktor83]

OverdriveNTool fan control does not seem to work with the new AMD drivers, any workarounds?
Edit: Trying the Latest OverdriverNTool now, I guess there's hope. I wish SRB supports native gpu freq/voltage/fan control in future! When new algo madness resolves itself, may dok can lean on that.

ODNT 0.2.8 beta should work with the new drivers.
Sorry but i won't do any ADL stuff anymore, amd just likes to change those really frequently, and also everyone uses ODNT, so everything can be set there already.

[abg00]

Who can advise what is the best coin for now on cryptonight to mining with 2gb rx 550 gpu's
i am dropped from mining for last half year

any coin with best price

monero haven bittube massary xcash conceal etc