SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching

[AlexMineX]

Hi,

Need some guidance. I have Rigs with RX580 - bios moded.
I was mining Cryptonight algo - Tube for quite some time. My rigs were with Blockchain AMD drivers and SRBMiner 1.7.3 - I have very small problems with rigs, from some time the miner software crashes but is something like once in a 2-3 days. I just restart the miner software and continue to mine for another 2-3 days. When it crashes my rig is  ~140 W till i restart it. SRBRestarter does not work for some reason probably because see that the process is ON /crashed but is not absent /

I decided to upgrade the miner with the last version first without changing the drivers. And all the problems started every night at about the same time all rigs stop sending to the pool but they continue to draw full power from the wall .
I tried to set --minrigspeed but the miner works at full power just not submitting to the pool  so the string does not work for me /pool is https://bittube.miner.rocks/

Then I changed the drivers with 18.5.1 but without luck - the problem stays. It works for most of the day but then stops submitting to the pool and continues to draw full power from the wall /and not 140w like with 1.7.3/

Current setup is
SRB Miner 1.9.3
Afterburner 4.5.0
AMD Driver 18.5.1

Screenshot https://pasteboard.co/IrsHrzW.png

Also have similar problem. Use to be 24/7 stable ~0.1% HW errors.
Been mining TUBE on and off so I can't figure out exactly when the problem started but I think after SRBMiner v1.8.8.
Happens after 1-3 days of mining, then all of a sudden starts spitting out 100% HW errors, continues retrieving jobs from pool but doesn't restart.

Current setup:
5x Vega 56s (no bios mod)
AMD drivers 18.6.1
SRB Miner v1.9.3 (Run through AwesomeMiner + Remote Agent if that makes a difference, although never used to be a problem)
Parameters: --ccryptonighttype bittubev2 --cgpuid 0,1,2,3,4 --cgpuintensity 56,56,56,56,56 --cgpuworksize 8,8,8,8,8 --cgputhreads 2,2,2,2,2 --cgpufragments 1,1,1,1,1 --cgputweakprofile 5L,10L,10L,2,9L --cgpuheavymode 2,2,2,1,2 --resetvega --enablegpurampup --nobinaries --preparedata

Still trying to figure it out with low clocks ~900mhz atm but still same problem.
--nobinaries doesn't help.
 

The strange thing is that I have 4 rigs and they start almost at the same time at night around 6.30 AM - like something triggers them at this time /they are not in the same room and different power supply/electric phase - I have 3 phase electricity option and put rigs at different to distribute the load /.

I made little test - returned 3 of the rigs to 1.7.3 and they are working from 2 days but the 4th is with 1.9.3 and 18.5.1 and today again at 6.45 AM started to give errors

[doktor83]

I decided to upgrade the miner with the last version first without changing the drivers. And all the problems started every night at about the same time all rigs stop sending to the pool but they continue to draw full power from the wall .
I tried to set --minrigspeed but the miner works at full power just not submitting to the pool  so the string does not work for me /pool is https://bittube.miner.rocks/

Then I changed the drivers with 18.5.1 but without luck - the problem stays. It works for most of the day but then stops submitting to the pool and continues to draw full power from the wall /and not 140w like with 1.7.3/

Current setup is
SRB Miner 1.9.3
Afterburner 4.5.0
AMD Driver 18.5.1

Screenshot https://pasteboard.co/IrsHrzW.png

There is nothing that would restart the rig on a lot of compute errors (compute error = gpu and cpu got a different result for the same nonce), so --minrigspeed can't do anything here.
Your cards are hashing and working on new jobs , but they get all results wrong, that's why nothing is sent to the pool.

Are you guys using the tweaking profiles?
That could produce this kind of issue.

If you do, it would be nice to run the miner without it and see if this issue still exists. (use the --disabletweaking parameter).

The strange thing is that I have 4 rigs and they start almost at the same time at night around 6.30 AM - like something triggers them at this time /they are not in the same room and different power supply/electric phase - I have 3 phase electricity option and put rigs at different to distribute the load /.

I made little test - returned 3 of the rigs to 1.7.3 and they are working from 2 days but the 4th is with 1.9.3 and 18.5.1 and today again at 6.45 AM started to give errors

You say that no matter when you start the miner, on 4 rigs it will start spitting incorrect shares at the same time ? (6.30am).
I don't know any reason for this, there is no built in timer or something that would trigger this.

Could you please do this on the rig with v1.9.3 :
- remove video driver with DDU (very important to use DDU)
- install 18.6.1
- disable tweaking with --disabletweaking parameter

Can you upload a log from miner start somewhere and send me the link in PM, so i can inspect it ?
Also config file if you use it, or start parameters.
Thanks

[maxity]

doktor83,
B2N is no longer supported?
Today program has stopped connecting to devpool srbminer.com:443, when b2n is mined. And  load on processor grows, then mining stops "there is no connection with devpool." Although  site srbminer.com works with my ip, cloudflare does not ban me.
But when other coins are mined, such as XMR, CCX, connection to devpool is good.

[doktor83]

doktor83,
B2N is no longer supported?
Today program has stopped connecting to devpool srbminer.com:443, when b2n is mined. And  load on processor grows, then mining stops "there is no connection with devpool." Although  site srbminer.com works with my ip, cloudflare does not ban me.
But when other coins are mined, such as XMR, CCX, connection to devpool is good.

You are right, it was pointing to a non-existent pool. Going to fix it in 15 minutes, thanks for reporting!

[KolordZ]

Hi Guys!
I've been working on the constellation MiningRig Vega64 for the past 2 years - water cooled and fe cooled mix.

With the following settings and setup:

SRB Miner 1.9.3.
Windows 10 (1803)
Adrenaline Driver 18.6.1
ASUS B250 Mining Expert
8x Vega64 - WATER cooled // 4x Vega64 FE

Today I spent the whole day testing my rig again and again and again, and was able to reach the following values:

Highest daily value: 2346 H/s
https://drive.google.com/file/d/1uYAECE4AHwyW87EuXRnN7DFuBFH4PWBO/view?usp=sharing

Settings CONFIG:
{"id": 0, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},
{"id": 1, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},

POWERTABLE settings:
https://drive.google.com/file/d/1E13BCCLTxWO6yf4sGDfVG93XAiw-HRE7/view?usp=sharing
Download LINK:
https://drive.google.com/file/d/1UDGf8JcuKY4mFrSiFdrcWeYd24Gh2rtT/view?usp=sharing

(IMPORTANT: Then adjust the values in the OverdrivnTool for P7 and P3 to: 1435Mhz // 966mV and 1100Mhz // 923mV

I have now searched for a strong and stable attitude and personally changed something. I have also tried to reduce power consumption a little, but it comes with P7 (mV) from 950 crash of the system. So 966mV I think is the safest and option, with P3 (mV) 923 is very close, as I have a lot of experience with P3 (MhZ) of 1100, where they have set in the old PowerTables between 905mv and 915mv, that often crashed the system.
Maybe those are not the best values, but I'm pretty happy. I am always happy to work on it and reach new heights in mining with my Vega`s.  

I worked for a long time with the TABLE // P7 - 1408/915 and P3 - 1100/905, but unfortunately I had to realize that these are no longer stable or I could not find a stable version and I tried a lot.

I hope I could possibly help, you can always send me a message.

Best regards
Patrick

Hi Patrick !

That's what I've with my config :

https://drive.google.com/open?id=1NeA_xZSNHb0ztyQ05SygDjfXp3DezStL

So I don't understand why are you using this config if you have less H/s than me ?

When I try your config I have less too.

[lsHaKeRl]

Hi Guys!
I've been working on the constellation MiningRig Vega64 for the past 2 years - water cooled and fe cooled mix.

With the following settings and setup:

SRB Miner 1.9.3.
Windows 10 (1803)
Adrenaline Driver 18.6.1
ASUS B250 Mining Expert
8x Vega64 - WATER cooled // 4x Vega64 FE

Today I spent the whole day testing my rig again and again and again, and was able to reach the following values:

Highest daily value: 2346 H/s
https://drive.google.com/file/d/1uYAECE4AHwyW87EuXRnN7DFuBFH4PWBO/view?usp=sharing

Settings CONFIG:
{"id": 0, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},
{"id": 1, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},

POWERTABLE settings:
https://drive.google.com/file/d/1E13BCCLTxWO6yf4sGDfVG93XAiw-HRE7/view?usp=sharing
Download LINK:
https://drive.google.com/file/d/1UDGf8JcuKY4mFrSiFdrcWeYd24Gh2rtT/view?usp=sharing

(IMPORTANT: Then adjust the values in the OverdrivnTool for P7 and P3 to: 1435Mhz // 966mV and 1100Mhz // 923mV

I have now searched for a strong and stable attitude and personally changed something. I have also tried to reduce power consumption a little, but it comes with P7 (mV) from 950 crash of the system. So 966mV I think is the safest and option, with P3 (mV) 923 is very close, as I have a lot of experience with P3 (MhZ) of 1100, where they have set in the old PowerTables between 905mv and 915mv, that often crashed the system.
Maybe those are not the best values, but I'm pretty happy. I am always happy to work on it and reach new heights in mining with my Vega`s.  

I worked for a long time with the TABLE // P7 - 1408/915 and P3 - 1100/905, but unfortunately I had to realize that these are no longer stable or I could not find a stable version and I tried a lot.

I hope I could possibly help, you can always send me a message.

Best regards
Patrick

Hi Patrick !

That's what I've with my config :

https://drive.google.com/open?id=1NeA_xZSNHb0ztyQ05SygDjfXp3DezStL

So I don't understand why are you using this config if you have less H/s than me ?

When I try your config I have less too.

Hi Mate!
Thx for your reply!

I know well that it is possible to clock the bars even higher, but of course it costs more electricity!

I'm from Austria, where the price per kilowatt is about 0.21 € (cent). So not very cheap, of course I could too
my graphics cards to 1750Mhz clock (WaterCooled), but the cards should work longer, haha  
I personally think of it as "middlething" .. I said yes there are higher values possible, but not every person has low electricity prices.

Of course I will continue to try other options and continue testing.
I am currently working with 2x ENERMAX PLATIMAX 1700Watt power supplies and have found that the power consumption with higher version of the SRB-Miner has continued to increase.

I can still remember that earlier versions were about ~ 180 watts / Vega64 card, now we are now at ~ 210 - 230 watts per / card;)
Of course, there were also allgorythm changes, which increased the power consumption in any case.

I've seen your values that you've tested 3 graphics cards, I have 12 pieces, that's of course another big piece. Where you just have to take care of a lot more so that the system does not break or collapse  

My personal aim is to get high performance, but to consume less power.

So step by step.

anyway THANK YOU!

Greetings Patrick

[lsHaKeRl]

Hi,

Need some guidance. I have Rigs with RX580 - bios moded.
I was mining Cryptonight algo - Tube for quite some time. My rigs were with Blockchain AMD drivers and SRBMiner 1.7.3 - I have very small problems with rigs, from some time the miner software crashes but is something like once in a 2-3 days. I just restart the miner software and continue to mine for another 2-3 days. When it crashes my rig is  ~140 W till i restart it. SRBRestarter does not work for some reason probably because see that the process is ON /crashed but is not absent /

I decided to upgrade the miner with the last version first without changing the drivers. And all the problems started every night at about the same time all rigs stop sending to the pool but they continue to draw full power from the wall .
I tried to set --minrigspeed but the miner works at full power just not submitting to the pool  so the string does not work for me /pool is https://bittube.miner.rocks/

Then I changed the drivers with 18.5.1 but without luck - the problem stays. It works for most of the day but then stops submitting to the pool and continues to draw full power from the wall /and not 140w like with 1.7.3/

Current setup is
SRB Miner 1.9.3
Afterburner 4.5.0
AMD Driver 18.5.1

Screenshot https://pasteboard.co/IrsHrzW.png

Also have similar problem. Use to be 24/7 stable ~0.1% HW errors.
Been mining TUBE on and off so I can't figure out exactly when the problem started but I think after SRBMiner v1.8.8.
Happens after 1-3 days of mining, then all of a sudden starts spitting out 100% HW errors, continues retrieving jobs from pool but doesn't restart.

Current setup:
5x Vega 56s (no bios mod)
AMD drivers 18.6.1
SRB Miner v1.9.3 (Run through AwesomeMiner + Remote Agent if that makes a difference, although never used to be a problem)
Parameters: --ccryptonighttype bittubev2 --cgpuid 0,1,2,3,4 --cgpuintensity 56,56,56,56,56 --cgpuworksize 8,8,8,8,8 --cgputhreads 2,2,2,2,2 --cgpufragments 1,1,1,1,1 --cgputweakprofile 5L,10L,10L,2,9L --cgpuheavymode 2,2,2,1,2 --resetvega --enablegpurampup --nobinaries --preparedata

Still trying to figure it out with low clocks ~900mhz atm but still same problem.
--nobinaries doesn't help.
 

Hiho Guys!
I have read your reports, so
1.HW Error's: comes from my experience, directly from the chips, by overheating or if the ventilation ducts are dirty with dust.
I would also try to reduce some of the performance and to test if it might be because of it.
It's just a constant game. HAHA
2.Crashes after 2-3 days: Unfortunately, I have no direct answer or experience, I would only have tips:
Is the MiningRig connected alone or on its own power distributor? Are there any other devices in the circuit? The European standard current distributors usually only have a power distribution of 3680watt. Have any parts been changed or rebuilt lately?
Would also recommend to see if the graphics cards are clean and dust-free.
Maybe a Windows setting? Such as standby of the hard disk, maybe turned on? Screen saver activated? Sometimes these things make problems.

Unfortunately, I also have the experience that PSUs after a long time, the performance can no longer hold.

I can only give the tip to unscrew the card case and clean carefully with the vacuum cleaner or a brush and once every 2 months at 24H continuous operation.

If you / you already do this, then the chips are already very stressed, can also happen from overclocking or if it is just too hot in the room´s and the chips reach 60-75 degrees possible.

And please pay attention:
The RECOMMENDED versions currently are:
ADRENALINE 18.6.1
SRB 1.9.3
Latest WINDOWS 10 (1803)
(I would also recommend keeping BIOS up-to-date)

All other versions are a matter of luck, I would not recommend!

I hope i could help you, check this out.

Best regards
Patrick

[KolordZ]

Hi Guys!
I've been working on the constellation MiningRig Vega64 for the past 2 years - water cooled and fe cooled mix.

With the following settings and setup:

SRB Miner 1.9.3.
Windows 10 (1803)
Adrenaline Driver 18.6.1
ASUS B250 Mining Expert
8x Vega64 - WATER cooled // 4x Vega64 FE

Today I spent the whole day testing my rig again and again and again, and was able to reach the following values:

Highest daily value: 2346 H/s
https://drive.google.com/file/d/1uYAECE4AHwyW87EuXRnN7DFuBFH4PWBO/view?usp=sharing

Settings CONFIG:
{"id": 0, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},
{"id": 1, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},

POWERTABLE settings:
https://drive.google.com/file/d/1E13BCCLTxWO6yf4sGDfVG93XAiw-HRE7/view?usp=sharing
Download LINK:
https://drive.google.com/file/d/1UDGf8JcuKY4mFrSiFdrcWeYd24Gh2rtT/view?usp=sharing

(IMPORTANT: Then adjust the values in the OverdrivnTool for P7 and P3 to: 1435Mhz // 966mV and 1100Mhz // 923mV

I have now searched for a strong and stable attitude and personally changed something. I have also tried to reduce power consumption a little, but it comes with P7 (mV) from 950 crash of the system. So 966mV I think is the safest and option, with P3 (mV) 923 is very close, as I have a lot of experience with P3 (MhZ) of 1100, where they have set in the old PowerTables between 905mv and 915mv, that often crashed the system.
Maybe those are not the best values, but I'm pretty happy. I am always happy to work on it and reach new heights in mining with my Vega`s.  

I worked for a long time with the TABLE // P7 - 1408/915 and P3 - 1100/905, but unfortunately I had to realize that these are no longer stable or I could not find a stable version and I tried a lot.

I hope I could possibly help, you can always send me a message.

Best regards
Patrick

Hi Patrick !

That's what I've with my config :

https://drive.google.com/open?id=1NeA_xZSNHb0ztyQ05SygDjfXp3DezStL

So I don't understand why are you using this config if you have less H/s than me ?

When I try your config I have less too.

Hi Mate!
Thx for your reply!

I know well that it is possible to clock the bars even higher, but of course it costs more electricity!

I'm from Austria, where the price per kilowatt is about 0.21 € (cent). So not very cheap, of course I could too
my graphics cards to 1750Mhz clock (WaterCooled), but the cards should work longer, haha  
I personally think of it as "middlething" .. I said yes there are higher values possible, but not every person has low electricity prices.

Of course I will continue to try other options and continue testing.
I am currently working with 2x ENERMAX PLATIMAX 1700Watt power supplies and have found that the power consumption with higher version of the SRB-Miner has continued to increase.

I can still remember that earlier versions were about ~ 180 watts / Vega64 card, now we are now at ~ 210 - 230 watts per / card;)
Of course, there were also allgorythm changes, which increased the power consumption in any case.

I've seen your values that you've tested 3 graphics cards, I have 12 pieces, that's of course another big piece. Where you just have to take care of a lot more so that the system does not break or collapse  

My personal aim is to get high performance, but to consume less power.

So step by step.

anyway THANK YOU!

Greetings Patrick

Patrick,

Thanks for your reply.

When I use tweaking profil 10 I've some Invalid job appears.. I don't know why. I have Sapphire RX Vegas 64 Nitro+ and when I look Doktor and you on tweak profil 10 you don't have invalid shares... Why i'm getting this ? (In 1h I've got 3/55 invalid)

Something wrong with my config ?

Another question, in that case where you don't have to pay electricy what kind of config can we use with our cards to get the best and stable performance ?

Thanks !

[zafa]

Hi @doktor83
Is there any relase plan for linux?

[404_not_found]

@doktor83 Would you mind sharing the mem tweak settings for Profile 7? Much appreciated

[lsHaKeRl]

Patrick,

Thanks for your reply.

When I use tweaking profil 10 I've some Invalid job appears.. I don't know why. I have Sapphire RX Vegas 64 Nitro+ and when I look Doktor and you on tweak profil 10 you don't have invalid shares... Why i'm getting this ? (In 1h I've got 3/55 invalid)

Something wrong with my config ?

Another question, in that case where you don't have to pay electricy what kind of config can we use with our cards to get the best and stable performance ?

Thanks!

Hi Mate!

So because of the invalid shares:

It can happen, but mostly the servers or the pools are the reason. Just have a look at the "Stats". It could also be that the pool is in another region, YOU might have looked? Maybe the wrong port?

It could be the internet connection which might be too slow, it could just be the wrong server or wrong region from the pool as described above.

Your attitudes I believe are the same as mine.

These are my "Start Settings":

setx GPU_MAX_HEAP_SIZE 100
setx GPU_MAX_USE_SYNC_OBJECTS 1
setx GPU_SINGLE_ALLOC_PERCENT 100
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_MAX_SINGLE_ALLOC_PERCENT 100
@echo off
cd% ~ dp0

SRBMiner-CN.exe --config config \ config-normalv4.txt --pools pools.txt

AND

{ "id" : 0, "intensity" : 124, "worksize" : 16, "threads" : 2, "tweak_profile" : 10},

do you have others?

Topic high performance: (without thinking about power consumption)
https://drive.google.com/file/d/1AiuqbS6gbPW6IsT7p8QmgB6GrfIphHzB/view?usp=sharing

We are now @2450 H/s
OverdriveNTool settings:
P7 1680Mhz / 1000mV - P3 1100Mhz / 923mV

So I did not manage to do more without a crash at the moment. HAHA

Greetings
Patrick

[livada]

Hi Guys!
I've been working on the constellation MiningRig Vega64 for the past 2 years - water cooled and fe cooled mix.

With the following settings and setup:

SRB Miner 1.9.3.
Windows 10 (1803)
Adrenaline Driver 18.6.1
ASUS B250 Mining Expert
8x Vega64 - WATER cooled // 4x Vega64 FE

Today I spent the whole day testing my rig again and again and again, and was able to reach the following values:

Highest daily value: 2346 H/s
https://drive.google.com/file/d/1uYAECE4AHwyW87EuXRnN7DFuBFH4PWBO/view?usp=sharing

Settings CONFIG:
{"id": 0, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},
{"id": 1, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},

POWERTABLE settings:
https://drive.google.com/file/d/1E13BCCLTxWO6yf4sGDfVG93XAiw-HRE7/view?usp=sharing
Download LINK:
https://drive.google.com/file/d/1UDGf8JcuKY4mFrSiFdrcWeYd24Gh2rtT/view?usp=sharing

(IMPORTANT: Then adjust the values in the OverdrivnTool for P7 and P3 to: 1435Mhz // 966mV and 1100Mhz // 923mV

I have now searched for a strong and stable attitude and personally changed something. I have also tried to reduce power consumption a little, but it comes with P7 (mV) from 950 crash of the system. So 966mV I think is the safest and option, with P3 (mV) 923 is very close, as I have a lot of experience with P3 (MhZ) of 1100, where they have set in the old PowerTables between 905mv and 915mv, that often crashed the system.
Maybe those are not the best values, but I'm pretty happy. I am always happy to work on it and reach new heights in mining with my Vega`s.  

I worked for a long time with the TABLE // P7 - 1408/915 and P3 - 1100/905, but unfortunately I had to realize that these are no longer stable or I could not find a stable version and I tried a lot.

I hope I could possibly help, you can always send me a message.

Best regards
Patrick

Hi Patrick !

That's what I've with my config :

https://drive.google.com/open?id=1NeA_xZSNHb0ztyQ05SygDjfXp3DezStL

So I don't understand why are you using this config if you have less H/s than me ?

When I try your config I have less too.

Hi Mate!
Thx for your reply!

I know well that it is possible to clock the bars even higher, but of course it costs more electricity!

I'm from Austria, where the price per kilowatt is about 0.21 € (cent). So not very cheap, of course I could too
my graphics cards to 1750Mhz clock (WaterCooled), but the cards should work longer, haha  
I personally think of it as "middlething" .. I said yes there are higher values possible, but not every person has low electricity prices.

Of course I will continue to try other options and continue testing.
I am currently working with 2x ENERMAX PLATIMAX 1700Watt power supplies and have found that the power consumption with higher version of the SRB-Miner has continued to increase.

I can still remember that earlier versions were about ~ 180 watts / Vega64 card, now we are now at ~ 210 - 230 watts per / card;)
Of course, there were also allgorythm changes, which increased the power consumption in any case.

I've seen your values that you've tested 3 graphics cards, I have 12 pieces, that's of course another big piece. Where you just have to take care of a lot more so that the system does not break or collapse  

My personal aim is to get high performance, but to consume less power.

So step by step.

anyway THANK YOU!

Greetings Patrick

Srb miner wont power. iff you wont consume less power just try TeamRedMinerhttps://bitcointalk.org/index.php?topic=5059817.0.

vega64LE 2460hr+ 150W/CNR or 2300hr 135W/TUBE. mem 1100mhz 860/870mv gpu 1450mhz 850/860mv.

http://imgbox.com/TzsvzlCa
https://images2.imgbox.com/0c/75/xPKMH44N_o.jpg

vega56 2340hr+

2*vega 56@64bios + 1Vega64LE CNR = 7100HR 650/680W from the wall.
LE use more power for water cooled(20W+) and this rig have 1+ vega 56 in slot(?? 10/20w+) and 6 extra fun.
http://imgbox.com/vNHF2cqb

mem tweak : samsung
WinAMDTweak.exe --RAS 28 --RCDRD 12 --RCDWR 5 --RC 44 --RP 12 --RRDS 3 --RRDL 3 --REF 15600 --RFC 246 --FAW 14

mem tweak hynix
WinAMDTweak.exe --RAS 24 --rp 14 --rc 35 --rfc 168 --rrds 4 --rrdl 5 --rcdrd 19 --rcdwr 7 --REF 15600

[mk111]

Hi Guys!
I've been working on the constellation MiningRig Vega64 for the past 2 years - water cooled and fe cooled mix.

With the following settings and setup:

SRB Miner 1.9.3.
Windows 10 (1803)
Adrenaline Driver 18.6.1
ASUS B250 Mining Expert
8x Vega64 - WATER cooled // 4x Vega64 FE

Today I spent the whole day testing my rig again and again and again, and was able to reach the following values:

Highest daily value: 2346 H/s
https://drive.google.com/file/d/1uYAECE4AHwyW87EuXRnN7DFuBFH4PWBO/view?usp=sharing

Settings CONFIG:
{"id": 0, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},
{"id": 1, "intensity": 124, "worksize": 16, "threads": 2, "tweak_profile": 10},

POWERTABLE settings:
https://drive.google.com/file/d/1E13BCCLTxWO6yf4sGDfVG93XAiw-HRE7/view?usp=sharing
Download LINK:
https://drive.google.com/file/d/1UDGf8JcuKY4mFrSiFdrcWeYd24Gh2rtT/view?usp=sharing

(IMPORTANT: Then adjust the values in the OverdrivnTool for P7 and P3 to: 1435Mhz // 966mV and 1100Mhz // 923mV

I have now searched for a strong and stable attitude and personally changed something. I have also tried to reduce power consumption a little, but it comes with P7 (mV) from 950 crash of the system. So 966mV I think is the safest and option, with P3 (mV) 923 is very close, as I have a lot of experience with P3 (MhZ) of 1100, where they have set in the old PowerTables between 905mv and 915mv, that often crashed the system.
Maybe those are not the best values, but I'm pretty happy. I am always happy to work on it and reach new heights in mining with my Vega`s.  

I worked for a long time with the TABLE // P7 - 1408/915 and P3 - 1100/905, but unfortunately I had to realize that these are no longer stable or I could not find a stable version and I tried a lot.

I hope I could possibly help, you can always send me a message.

Best regards
Patrick

Hi Patrick !

That's what I've with my config :

https://drive.google.com/open?id=1NeA_xZSNHb0ztyQ05SygDjfXp3DezStL

So I don't understand why are you using this config if you have less H/s than me ?

When I try your config I have less too.

Hi Mate!
Thx for your reply!

I know well that it is possible to clock the bars even higher, but of course it costs more electricity!

I'm from Austria, where the price per kilowatt is about 0.21 € (cent). So not very cheap, of course I could too
my graphics cards to 1750Mhz clock (WaterCooled), but the cards should work longer, haha  
I personally think of it as "middlething" .. I said yes there are higher values possible, but not every person has low electricity prices.

Of course I will continue to try other options and continue testing.
I am currently working with 2x ENERMAX PLATIMAX 1700Watt power supplies and have found that the power consumption with higher version of the SRB-Miner has continued to increase.

I can still remember that earlier versions were about ~ 180 watts / Vega64 card, now we are now at ~ 210 - 230 watts per / card;)
Of course, there were also allgorythm changes, which increased the power consumption in any case.

I've seen your values that you've tested 3 graphics cards, I have 12 pieces, that's of course another big piece. Where you just have to take care of a lot more so that the system does not break or collapse  

My personal aim is to get high performance, but to consume less power.

So step by step.

anyway THANK YOU!

Greetings Patrick

Srb miner wont power. iff you wont consume less power just try TeamRedMinerhttps://bitcointalk.org/index.php?topic=5059817.0.

vega64LE 2460hr+ 150W/CNR or 2300hr 135W/TUBE. mem 1100mhz 860/870mv gpu 1450mhz 850/860mv.




vega56 2340hr+

2*vega 56@64bios + 1Vega64LE CNR = 7100HR 650/680W from the wall.
LE use more power for water cooled(20W+) and this rig have 1+ vega 56 in slot(?? 10/20w+) and 6 extra fun.


mem tweak : samsung
WinAMDTweak.exe --RAS 28 --RCDRD 12 --RCDWR 5 --RC 44 --RP 12 --RRDS 3 --RRDL 3 --REF 15600 --RFC 246 --FAW 14

mem tweak hynix
WinAMDTweak.exe --RAS 24 --rp 14 --rc 35 --rfc 168 --rrds 4 --rrdl 5 --rcdrd 19 --rcdwr 7 --REF 15600

Why does TeamRedMiner use less power?
Is there plans for newer versions of SRB to lower power use?

[lsHaKeRl]

Why does TeamRedMiner use less power?
Is there plans for newer versions of SRB to lower power use?

The reason for this is the CLOCK (PowerTable) settings. They are really good, I have to try!

THANK YOU!  

AMDTWEAKING and OverdrivnTool 0.2.8 are NOT running for 18.6.1, so can´t use SRB-Miner with it, NEED the RegistryFile for
the 800-866mV.

TEAMREDMINER has 2,5% DevFee, sorry but that´s really a hard joke.  

greetings
Patrick

[lsHaKeRl]

Srb miner wont power. iff you wont consume less power just try TeamRedMinerhttps://bitcointalk.org/index.php?topic=5059817.0.

vega64LE 2460hr+ 150W/CNR or 2300hr 135W/TUBE. mem 1100mhz 860/870mv gpu 1450mhz 850/860mv.

http://imgbox.com/TzsvzlCa
https://images2.imgbox.com/0c/75/xPKMH44N_o.jpg

vega56 2340hr+

2*vega 56@64bios + 1Vega64LE CNR = 7100HR 650/680W from the wall.
LE use more power for water cooled(20W+) and this rig have 1+ vega 56 in slot(?? 10/20w+) and 6 extra fun.
http://imgbox.com/vNHF2cqb

mem tweak : samsung
WinAMDTweak.exe --RAS 28 --RCDRD 12 --RCDWR 5 --RC 44 --RP 12 --RRDS 3 --RRDL 3 --REF 15600 --RFC 246 --FAW 14

mem tweak hynix
WinAMDTweak.exe --RAS 24 --rp 14 --rc 35 --rfc 168 --rrds 4 --rrdl 5 --rcdrd 19 --rcdwr 7 --REF 15600

Hi Mate!

Is it maybe possible to post your POWERTABLE values in here, or send it on a downloadlink for RegistryFile? I would be very nice and kind!  

Dont want to use TEAMREDMINER he has 2,5% DevFee lol.. SRB-Miner has 0,85%. BUT thanks anyway!

Greetings
Patrick

[doktor83]

Hi Mate!

Is it maybe possible to post your POWERTABLE values in here, or send it on a downloadlink for RegistryFile? I would be very nice and kind!  

Dont want to use TEAMREDMINER he has 2,5% DevFee lol.. SRB-Miner has 0,85%. BUT thanks anyway!

Greetings
Patrick

I am ignoring this guy because he is just a plain dickhead, doing nothing else than hijacking my thread so he can advertise TRM miner, doing some kiddy revenge stuff or idk. I see his messages only when someone quotes them, but then again i don't really read them

TeamRed guys do their kernels in gcn assembler, it allows them to have more control, that i can't achieve with opencl, so yes, the power consumption may be lower with their miner.
Maybe once i will dive into GCN ASM and this new RDNA thing. It needs unbeliveably a lot of free time, that i don't really have.

Patrick you can use SRB with the latest drivers too, but if you don't use the pre-built kernels , but compile on the new drivers, you will probably have worse hashrate.

[livada]

Hi Mate!

Is it maybe possible to post your POWERTABLE values in here, or send it on a downloadlink for RegistryFile? I would be very nice and kind!  

Dont want to use TEAMREDMINER he has 2,5% DevFee lol.. SRB-Miner has 0,85%. BUT thanks anyway!

Greetings
Patrick

I am ignoring this guy because he is just a plain dickhead, doing nothing else than hijacking my thread so he can advertise TRM miner, doing some kiddy revenge stuff or idk. I see his messages only when someone quotes them, but then again i don't really read them

TeamRed guys do their kernels in gcn assembler, it allows them to have more control, that i can't achieve with opencl, so yes, the power consumption may be lower with their miner.
Maybe once i will dive into GCN ASM and this new RDNA thing. It needs unbeliveably a lot of free time, that i don't really have.

Patrick you can use SRB with the latest drivers too, but if you don't use the pre-built kernels , but compile on the new drivers, you will probably have worse hashrate.

now all see  why DOCTOR sucker. they all blame him for not being smart enough to use assembler..
if you ask why HR little he say fck off
if you ask why your miner use more power he say you hijacking my thread...

today i send SS for all mesage  DOCTOR send me  on PM.
you will see how much he hates TRM  DEV. and ELIOVP (amd tweak DEv).

this PM is before i ask doctor why stole ELIOVP programs and block AMDmemtweak. after this question he block me.

[livada]

Srb miner wont power. iff you wont consume less power just try TeamRedMinerhttps://bitcointalk.org/index.php?topic=5059817.0.

vega64LE 2460hr+ 150W/CNR or 2300hr 135W/TUBE. mem 1100mhz 860/870mv gpu 1450mhz 850/860mv.

http://imgbox.com/TzsvzlCa
https://images2.imgbox.com/0c/75/xPKMH44N_o.jpg

vega56 2340hr+

2*vega 56@64bios + 1Vega64LE CNR = 7100HR 650/680W from the wall.
LE use more power for water cooled(20W+) and this rig have 1+ vega 56 in slot(?? 10/20w+) and 6 extra fun.
http://imgbox.com/vNHF2cqb

mem tweak : samsung
WinAMDTweak.exe --RAS 28 --RCDRD 12 --RCDWR 5 --RC 44 --RP 12 --RRDS 3 --RRDL 3 --REF 15600 --RFC 246 --FAW 14

mem tweak hynix
WinAMDTweak.exe --RAS 24 --rp 14 --rc 35 --rfc 168 --rrds 4 --rrdl 5 --rcdrd 19 --rcdwr 7 --REF 15600

Hi Mate!

Is it maybe possible to post your POWERTABLE values in here, or send it on a downloadlink for RegistryFile? I would be very nice and kind!  

Dont want to use TEAMREDMINER he has 2,5% DevFee lol.. SRB-Miner has 0,85%. BUT thanks anyway!

Greetings
Patrick

VEGA 64LE : SOC 1107

"PP_PhmSoftPowerPlayTable"=hex:b6,02,08,01,00,5c,00,e1,06,00,00,ee,2b,00,00,1b,\
  00,48,00,00,00,80,a9,03,00,f0,49,02,00,8e,00,08,00,00,00,00,00,00,00,00,00,\
  00,00,00,00,00,02,01,5c,00,4f,02,46,02,94,00,9e,01,be,00,28,01,7a,00,8c,00,\
  bc,01,00,00,00,00,72,02,00,00,90,00,a8,02,6d,01,43,01,97,01,f0,49,02,00,71,\
  02,02,02,00,00,00,00,00,00,08,00,00,00,00,00,00,00,05,00,07,00,03,00,05,00,\
  00,00,00,00,00,00,01,08,20,03,21,03,22,03,23,03,24,03,25,03,2f,03,52,03,01,\
  01,52,03,01,01,84,03,00,08,60,ea,00,00,00,40,19,01,00,01,80,38,01,00,02,dc,\
  4a,01,00,03,90,5f,01,00,04,00,77,01,00,05,90,91,01,00,06,6C,B0,01,00,07,01,\
  08,d0,4c,01,00,00,00,80,00,00,00,00,00,00,1c,83,01,00,01,00,00,00,00,00,00,\
  00,00,70,a7,01,00,02,00,00,00,00,00,00,00,00,b0,ad,01,00,03,00,00,00,00,00,\
  00,00,00,74,b7,01,00,04,00,00,00,00,00,00,00,00,38,c1,01,00,05,00,00,00,00,\
  01,00,00,00,58,0f,02,00,06,00,00,00,00,01,00,00,00,68,36,02,00,07,00,00,00,\
  00,01,00,00,00,00,05,60,ea,00,00,00,40,19,01,00,00,80,38,01,00,00,dc,4a,01,\
  00,00,90,5f,01,00,00,00,08,28,6e,00,00,00,2c,c9,00,00,01,f8,0b,01,00,02,80,\
  38,01,00,03,90,5f,01,00,04,f4,91,01,00,05,d0,b0,01,00,06,c0,d4,01,00,07,00,\
  08,6c,39,00,00,00,24,5e,00,00,01,fc,85,00,00,02,ac,bc,00,00,03,34,d0,00,00,\
  04,68,6e,01,00,05,08,97,01,00,06,ec,a3,01,00,07,00,01,68,3c,01,00,00,01,04,\
  3c,41,00,00,00,00,00,50,c3,00,00,00,00,00,80,38,01,00,02,00,00,b0,ad,01,00,\
  04,00,00,01,08,00,98,85,00,00,40,b5,00,00,60,ea,00,00,50,c3,00,00,01,80,bb,\
  00,00,60,ea,00,00,94,0b,01,00,50,c3,00,00,02,00,e1,00,00,94,0b,01,00,40,19,\
  01,00,50,c3,00,00,03,78,ff,00,00,40,19,01,00,88,26,01,00,50,c3,00,00,04,40,\
  19,01,00,80,38,01,00,80,38,01,00,50,c3,00,00,05,80,38,01,00,dc,4a,01,00,dc,\
  4a,01,00,50,c3,00,00,06,00,77,01,00,00,77,01,00,90,5f,01,00,50,c3,00,00,07,\
  90,91,01,00,90,91,01,00,00,77,01,00,50,c3,00,00,01,18,00,00,00,00,00,00,00,\
  0b,e4,12,60,09,60,09,4b,00,0a,00,54,03,90,01,90,01,90,01,90,01,90,01,90,01,\
  90,01,00,00,00,00,00,02,04,31,07,dc,00,dc,00,dc,00,90,01,00,00,59,00,69,00,\
  4a,00,4a,00,5f,00,73,00,73,00,64,00,40,00,90,92,97,60,96,00,90,55,00,00,00,\
  00,00,00,00,00,00,00,00,00,00,00,00,00,00,02,02,d4,30,00,00,02,10,60,ea,00,\
  00,02,10


TRM have big  feebut if use matematic he better than srb.

You usay  SRB = 2346hr
TRM  have 2480hr
2480-2346= 134HR . This is 5-6 % beter HR. TRM use 5% litle power.
5%HR+ 5 % litle power i 2,5 fee is beter than 0,85 DEV fee.

Before i use SRB for all algo(see my old post) except CNR but after the doctor's uncontrollable behavior I switched to TRM.

TRM now use most cost-effective algorithms and give better HR in ALL algos.


TRM Algorithms:

    Cryptonight R (monero)
    Cryptonight v8 turtle (turtlecoin, loki)
    Cryptonight v8 half (stellite, masari)
    Cryptonight v8 double (x-cash)
    Cryptonight v8 reverse waltz (graft)
    Cryptonight v8 upx2 (uPlexa)
    Cryptonight v8
    Cryptonight heavy
    Cryptonight haven (haven)
    Cryptonight saber (bittube)
    Cryptonight conceal (conceal)
    x16r (rvn)
    x16s (pgn, xsh)
    x16rt (veil, gin)
    MTP (zcoin)
    Cuckarood29 (grin)
    Cuckatoo31 (grin)
    Lyra2rev3 (vtc)
    Lyra2z
    Phi2 (lux, argoneum)


this rig has too little power and have 6 extra fan.- Max 750W from the wall.

3*veg56 +1*vega64 - TUBE - TRM
WinAMDTweak.exe --i 0,1,2,3 --RAS 28 --RCDRD 12 --RCDWR 5 --RC 44 --RP 12 --RRDS 3 --RRDL 3 --REF 15600 --RFC 246 --FAW 14
8700hr 745W from the wall (11,6HR/W)


http://imgbox.com/IinUGubA
http://imgbox.com/OCOTBOSk

veg64:
GPU_P0=852;800;0
GPU_P1=991;801;0
GPU_P2=1084;802;0
GPU_P3=1100;803;0
GPU_P4=1125;804;0
GPU_P5=1150;805;0
GPU_P6=1350;840;0
GPU_P7=1480;862
Mem_P0=167;800;0
Mem_P1=500;800;0
Mem_P2=800;802;0
Mem_P3=1096;870
Mem_TimingLevel=0
Fan_P0=47;17
Fan_P1=49;27
Fan_P2=51;34
Fan_P3=53;45
Fan_P4=55;70
Fan_ZeroRPM=0
Fan_Acoustic=1400
Power_Target=0

veg56:
GPU_P0=852;800;0
GPU_P1=991;801;0
GPU_P2=1084;802;0
GPU_P3=1100;803;0
GPU_P4=1125;804;0
GPU_P5=1150;805;0
GPU_P6=1240;840;0
GPU_P7=1440;854
Mem_P0=167;800;0
Mem_P1=500;800;0
Mem_P2=800;802;0
Mem_P3=1100;870
Mem_TimingLevel=0
Fan_P0=56;45
Fan_P1=57;50
Fan_P2=58;58
Fan_P3=60;61
Fan_P4=64;75
Fan_ZeroRPM=0
Fan_Acoustic=1800
Power_Target=0

[maximus63]

Doc, thanks for your miner. I use it for 1.5 year. Now i'm on TRM, it's beter on All parameters. Good luck to you

[doktor83]

I knew there will be some reaction on my message, and as im in good mood right now, so i unignored that fool.
I aint gonna fight with you cause you are an idiot, and it is like when you die, you don't know you are dead but for others around you it is hard. The same goes when you are an idiot, you don't know about it but it's hard for everyone around you.
So this is for the normal users who want to know the story:

- My previous versions of SRB were blocking usage of Mem Tweak tool and SRB at the same time. After closing SRB sometimes you couldn't use Mem Tweak until you restart your machine. I told him x times if he wants to use the Mem Tweak tool and SRB he should use the --disabletweaking parameter. He kept raging and saying he had to reinstall windows twice (   ) because of me not wanting to help him. And of course that i wrote him to reinstall windows if he wants his problem gone. Well i would like to see that message quoted here please.

- We were PM-ing yes, he ocassionally reported to me some bugs about SRB, hashrates etc. Sometimes he asked for some help and if i could i helped him.
Also talked about the competition (TRM) and i did say the same thing i wrote to Patrick earlier, i can't compete with them really at the moment because they are working in ASM and i am not. I probably used some unoapropriate words too, you know how it goes when you get mad ..

About ElioVp, i believe i didn't say a bad word about him, i am grateful to him that he open sourced his tool so that helped me FINISH something i was already working on. I also donated BTC to him for his work, and also we exchanged a few PM's. I'll let everyone judge himself if i stole anything from him or not.

That's the story folks, decide for yourself who is right, who is not. Who is the shithead here, and who isn't.
Also it is up to you, the user, to decide which mining software you want to use. No need to come back here and say 20 times that TRM is better and SRB is shit.
Nobody is forcing you to use SRB.

I am waiting for your PM screenshots livada, and translate them correctly, i know it will be hard for you but please do this right at least.

now all see  why DOCTOR sucker. they all blame him for not being smart enough to use assembler..
if you ask why HR little he say fck of Smiley
if you ask why your miner use more power he say you hijacking my thread...

today i send SS for all mesage  DOCTOR send me  on PM.
you will see how much he hates TRM  DEV. and ELIOVP (amd tweak DEv).

this PM is before i ask doctor why stole ELIOVP programs and block AMDmemtweak. after this question he block me.


a ti mi se napusi velikog crnog...

Ok, i am a sucker, your opinion doesn't matter to me.
Who blames me for not 'being smart enough to use asm' ? Does this make any sense at all?
Who did i tell to fu*ck off if he wrote that he is not satisfied with SRB hashrate ? (please quote it here from the original message) (also if you are not satisfied you would go use other software)
Also please quote someone who asked me why is SRB using more power (more than what? ) and i told him to gtfo.

You are like a girl on a period. You just can't control yourself.

I wrote to the moderator after few posts you started doing 'your shit'. He replied me after 3 weeks that they don't have time to check all messages, altough your messages contain insults on your native language, and were full of hate, trolling and advertising. I daily see messages of those kind removed from other threads.
So please moderators don't just start doing your job now, and please don't delete this message, cause i want it to stay.

Oh , and 'a ti mi se napusi velikog crnog...' that he wrote means 'and you can suck my big black...' . Just showing of his level of culture again

We are waiting for your PM screenshots, quotes and everything you need to show to prove us you are not just hijacking & trolling & swearing for a no reason.
If you can't or don't want to prove it, please leave this thread. You are not using this miner anymore anyways, so you can't contribute anything here.
The moment i see there's no point in continuing this with you (and i have a feeling this will be after your next post )) ) you go back to ignored, and we all live again happy ever after.