SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching

[doktor83]

Пoдcкaжитe ктo нe бyдь,чтo зa aлгopитм cryptonight-superfast? ecть ли oн в SRBminere?

what coin? its english topic

кaкaя мoнeтa. пиши пo-aнглийcки, тoпикcтapтep pyccкий нe знaeт

Furycoin,here is this coin,on algorithm SuperFast

"cryptonight_type" : "cryptonight_superfast"
or
"cryptonight_type" : "swap"

I have a decent hr on cn pico (turtle) but cnR i have horrible and unstable.
Should i raise core clock? Mem clock is pretty much at max (hynix memory) and it can't get over 910.
What are optimal settings for vega56 on cnr?

Driver version you use ?
Also how does your config looks like?
What hashrate do you get on CN/R ?

[swongsR1thing]

I use 18.6.1.
CC: 1407 MHz
MC: 900 MHz (hynix memory - very unstable over ~910 on cn7, cn8)
HR cn pico turtle = ~14880 H/s

Code:

{
"cryptonight_type" : "turtle",
"intensity" : 0,
"double_threads" : true,
"shutdown_temperature" : 77,
"off_temperature" : 77
}

[doktor83]

I use 18.6.1.
CC: 1407 MHz
MC: 900 MHz (hynix memory - very unstable over ~910 on cn7, cn8)
HR cn pico turtle = ~14880 H/s

Code:

{
"cryptonight_type" : "turtle",
"intensity" : 0,
"double_threads" : true,
"shutdown_temperature" : 77,
"off_temperature" : 77
}

No, i mean't on Cn/r , you said you have problems on CN/r

[swongsR1thing]

Code:

{
"cryptonight_type" : "normalv4",
"intensity" : 161,
"worksize" : 16,
"double_threads" : true,
"shutdown_temperature" : 77,
"off_temperature" : 77
}

This is with 18.8.8

[Amgine]

Dok, how to disable the "Precompiling program"?
GPU can crash after a certain times of  these "Precompiling program" and hashrate dropped (as if it didn't load the tweak profile) after the Precompiling Program.

[doktor83]

Code:

{
"cryptonight_type" : "normalv4",
"intensity" : 161,
"worksize" : 16,
"double_threads" : true,
"shutdown_temperature" : 77,
"off_temperature" : 77
}

This is with 18.8.8

Try intensity 112

Dok, how to disable the "Precompiling program"?
GPU can crash after a certain times of  these "Precompiling program" and hashrate dropped (as if it didn't load the tweak profile) after the Precompiling Program.

You can't that is how CN/R works.

[swongsR1thing]

Ok, it has been running. I didn't do much, i downloaded 18.8.9. version and used guided setup. Then i just started the bat file. I don't even have setclock.bat or any other scripts running.
I used to have overdriventool.ini in the same folder and .bat file would execute clock speeds and settings from .ini file.
In this scenario i only have 18.8.9. and ran the miner and applied + for a step 1 tweak.
It does 1818 H/s at 1407cc and 900mc.

Should i put overdriventool in the folder or i just keep it running as it is?

[vitik]

v1.8.9
win10x64
reboot_script_min_rig_speed - not working

[MingMining]

some weird result on 1.8.8



GPU0: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 1]
GPU1: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 30]
GPU2: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 31]
GPU3: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 34]
GPU4: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 35]
GPU5: Radeon RX 570 Series [ellesmere] [4096 MB][I: 59.0][W: 16][T: 2][F: 8][BUS: 38]

--------------------------------------------------------------------------------------
SRBMiner Cryptonight AMD GPU miner 1.8.8
DevFee ~0.85%

Press 's' to display stats
Press 'h' to display hashrate
Press 'r' to reload pools
Press 'p' to switch to the next pool
Press 'o' to switch to the previous pool
Press 0-9 to disable/enable GPU 0-9, shift+0-9 for GPU 10-19
--------------------------------------------------------------------------------------

Recommended drivers     : Adrenalin 18.6.1 or Adrenalin 2019
Algorithm               : Cryptonight V4 (R)
Algo switching          : enabled
Coin forking            : enabled
Gpu watchdog            : enabled [normal mode]
Startup monitor         : enabled
Tweaking                : disabled


[2019-05-27 19:43:41] Pools defined -> 2
[2019-05-27 19:43:41] Please run miner as administrator to enable tweaking
[2019-05-27 19:43:42] Compiling [normalv4] kernel for DEVICE BUS_ID[1]
[2019-05-27 19:43:46] Loading [normalv4] kernel for DEVICE BUS_ID[1]
[2019-05-27 19:43:46] Loading [normalv4] kernel for DEVICE BUS_ID[30]
[2019-05-27 19:43:46] Loading [normalv4] kernel for DEVICE BUS_ID[30]
[2019-05-27 19:43:47] Loading [normalv4] kernel for DEVICE BUS_ID[31]
[2019-05-27 19:43:47] Loading [normalv4] kernel for DEVICE BUS_ID[31]
[2019-05-27 19:43:48] Loading [normalv4] kernel for DEVICE BUS_ID[34]
[2019-05-27 19:43:48] Loading [normalv4] kernel for DEVICE BUS_ID[34]
[2019-05-27 19:43:49] Loading [normalv4] kernel for DEVICE BUS_ID[35]
[2019-05-27 19:43:49] Loading [normalv4] kernel for DEVICE BUS_ID[35]
[2019-05-27 19:43:50] Loading [normalv4] kernel for DEVICE BUS_ID[38]
[2019-05-27 19:43:50] Loading [normalv4] kernel for DEVICE BUS_ID[38]
[2019-05-27 19:43:50] ADL initialised successfully
[2019-05-27 19:43:51] Connected to pool.supportxmr.com:7777
[2019-05-27 19:43:51] Pool difficulty: 40000
[2019-05-27 19:43:51] Pool sent a new job, block height 1844209 [ID: Qmj+TM6O22XoHgb5LSYc1TqLJrQm] [normalv4]
[2019-05-27 19:43:51] Precompiling program [BUS:1]
[2019-05-27 19:44:04] Pool sent a new job, block height 1844210 [ID: PLArP+CMDHmAblPA0AoEGE9AGIu0] [normalv4]
[2019-05-27 19:44:05] Finished program precompilation [BUS:1]
[2019-05-27 19:44:05] Precompiling program [BUS:30]
[2019-05-27 19:44:20] Finished program precompilation [BUS:30]
[2019-05-27 19:44:20] Precompiling program [BUS:34]
[2019-05-27 19:44:29] Pool difficulty: 40001
[2019-05-27 19:44:29] GPU1[BUS:30] result rejected for job[2] [low difficulty share]
[2019-05-27 19:44:35] Finished program precompilation [BUS:34]
[2019-05-27 19:44:35] Precompiling program [BUS:31]
[2019-05-27 19:44:50] Finished program precompilation [BUS:31]
[2019-05-27 19:44:50] Precompiling program [BUS:38]
[2019-05-27 19:44:55] GPU0[BUS:1] result rejected for job[2] [low difficulty share]
[2019-05-27 19:45:01] GPU3[BUS:34] result rejected for job[2] [low difficulty share]
[2019-05-27 19:45:04] Finished program precompilation [BUS:38]
[2019-05-27 19:45:04] Precompiling program [BUS:35]
[2019-05-27 19:45:08] GPU3[BUS:34] result rejected for job[2] [invalid job id]
[2019-05-27 19:45:14] GPU0[BUS:1] result rejected for job[2] [invalid job id]
[2019-05-27 19:45:16] GPU1[BUS:30] result rejected for job[2] [invalid job id]
[2019-05-27 19:45:19] Finished program precompilation [BUS:35]
[2019-05-27 19:45:19] Pool sent a new job, block height 1844210 [ID: uSxHgoDQ+6OTzv8/aSVByu4u+Ek/] [normalv4]
[2019-05-27 19:45:19] Pool difficulty: 21622
[2019-05-27 19:46:06] Pool difficulty: 21621
[2019-05-27 19:46:06] Pool sent a new job, block height 1844212 [ID: geRjmtGOjG9dU+3htvcv68e88nvQ] [normalv4]
[2019-05-27 19:46:06] GPU4[BUS:35] result rejected for job[11] [low difficulty share]
[2019-05-27 19:46:11] Pool difficulty: 21622
[2019-05-27 19:46:11] Pool sent a new job, block height 1844212 [ID: OP1sZcF7d35n33QkX7XBrBke8tC8] [normalv4]
[2019-05-27 19:46:12] GPU2[BUS:31] result rejected for job[12] [low difficulty share]
[2019-05-27 19:46:12] Pool difficulty: 14415
[2019-05-27 19:46:14] GPU1[BUS:30] result rejected for job[12] [low difficulty share]
[2019-05-27 19:46:16] GPU0[BUS:1] result rejected for job[12] [low difficulty share]
[2019-05-27 19:46:18] Pool sent a new job, block height 1844212 [ID: WcNRYrKmgUF15IT9/zk6QuhPQiyS] [normalv4]
[2019-05-27 19:46:18] GPU1[BUS:30] result rejected for job[13] [low difficulty share]
[2019-05-27 19:46:18] Pool difficulty: 14414
[2019-05-27 19:46:22] Pool sent a new job, block height 1844212 [ID: 1JeUETe3pNhJeBG0tCPMF6QKPbel] [normalv4]
[2019-05-27 19:46:25] Pool sent a new job, block height 1844212 [ID: oTPhwy4OxZveAUZqJ/LRkO6YHDhp] [normalv4]
[2019-05-27 19:46:29] Pool sent a new job, block height 1844212 [ID: G3cF+wAg6lmPK3WFjYEe+xPhS3wG] [normalv4]
[2019-05-27 19:46:32] Pool difficulty: 14415
[2019-05-27 19:46:32] GPU2[BUS:31] result rejected for job[16] [low difficulty share]
[2019-05-27 19:46:32] GPU4[BUS:35] result rejected for job[16] [low difficulty share]

[MingMining]

Hi Doc. Any idea what is the problem for the above message? I am using the right algo as you can see. Normal v4

[issie81]

Doc,

when i start miner with --cgputweakprofile 9,9,9,9 then the miner doesn't set level on 9
when i do + or - in the window it does adjust the level, so it does start with administrator

i am running my miners with Awesome Miner (miner being started with administrator privalige)

Why doesn't miner set the level at initial start and have to adjust manual..

[abg00]

when i start miner with --cgputweakprofile 9,9,9,9 then the miner doesn't set level on 9

confirm. work only in gpu_conf

[doktor83]

Hi Doc. Any idea what is the problem for the above message? I am using the right algo as you can see. Normal v4

I just tried pool.supportxmr.com:7777 and get valid results with v189. I have no idea what caused that.
Have you tried another pool ?

when i start miner with --cgputweakprofile 9,9,9,9 then the miner doesn't set level on 9

confirm. work only in gpu_conf

Wrong confirm, i just tested in cmd and it gets applied :

Code:

SRBMiner-CN.exe --ccryptonighttype conceal --cpool conceal.herominers.com:10361 --cwallet xxx --cgpuid 0,1,2,3 --cgpuintensity 0,0,0,0 --cgputhreads 2,2,2,2 --cgputweakprofile 5,4,3,2

I don't know how Awesome miner works, so have you checked without it ?

[abg00]

Wrong confirm, i just tested in cmd and it gets applied :

Code:

SRBMiner-CN.exe --ccryptonighttype conceal --cpool conceal.herominers.com:10361 --cwallet xxx --cgpuid 0,1,2,3 --cgpuintensity 0,0,0,0 --cgputhreads 2,2,2,2 --cgputweakprofile 5,4,3,2

I don't know how Awesome miner works, so have you checked without it ?

test again. rig 6 rx550 2 rx560 2gb card

"C:\SRBMiner-CN-V1-3-0\SRBMiner-CN.exe" --config config_tube.txt --pools pools_tube.txt --cgputweakprofile 10
"C:\SRBMiner-CN-V1-3-0\SRBMiner-CN.exe" --config config_tube.txt --pools pools_tube.txt --cgputweakprofile 10,10,10,10,10,10,10,10

!!!! both dont work

Enumerating OpenCL devices, please wait...

GPU0: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 1]
GPU1: Radeon RX 560 Series [baffin] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 2]
GPU2: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 3]
GPU3: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 4]
GPU4: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 5]
GPU5: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 7]
GPU6: Radeon RX 550 Series [gfx804] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 8]
GPU7: Radeon RX 560 Series [baffin] [2048 MB][I: 13.5][W: 8][T: 2][F: 1][BUS: 9]

---------------------------------------------------------------------------------
SRBMiner Cryptonight AMD GPU miner 1.8.9
DevFee ~0.85%

Press 's' to display stats
Press 'h' to display hashrate
Press 'r' to reload pools
Press 'p' to switch to the next pool
Press 'o' to switch to the previous pool
Press 0-9 to disable/enable GPU 0-9, shift+0-9 for GPU 10-19
Press + or - to change tweak profile
---------------------------------------------------------------------------------

Algorithm               : Cryptonight BitTube
Algo switching          : disabled
Coin forking            : disabled
Gpu watchdog            : enabled [normal mode]
Startup monitor         : enabled
Tweaking                : enabled


[2019-05-28 20:39:14] Pools defined -> 6
[2019-05-28 20:39:14] Loading [bittubev2] kernel for DEVICE BUS_ID[1]
[2019-05-28 20:39:14] Loading [bittubev2] kernel for DEVICE BUS_ID[1]
[2019-05-28 20:39:14] Loading [bittubev2] kernel for DEVICE BUS_ID[2]
[2019-05-28 20:39:14] Loading [bittubev2] kernel for DEVICE BUS_ID[2]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[3]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[3]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[4]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[4]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[5]
[2019-05-28 20:39:15] Loading [bittubev2] kernel for DEVICE BUS_ID[5]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[7]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[7]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[8]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[8]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[9]
[2019-05-28 20:39:16] Loading [bittubev2] kernel for DEVICE BUS_ID[9]
[2019-05-28 20:39:17] ADL initialised successfully
[2019-05-28 20:39:19] SSL/TLS fingerprint: SHA256:N0gJaTP2OaNI75CPbZWTRqMHCyOfLxO4FpCcVgHm2Lk=
[2019-05-28 20:39:19] Connected to bittube.miner.rocks:3333
[2019-05-28 20:39:19] Pool difficulty: 36094
[2019-05-28 20:39:19] Pool sent a new job [ID: 994210225048858]
[2019-05-28 20:39:23] GPU2[BUS:3] result 0x400001A2 accepted for job[1] [107ms]


return to gpu_conf all ok

   { "id" : 1, "intensity" : 13.5, "double_threads" : true, "worksize" : 8, "tweak_profile" : 10},

[doktor83]

test again ))

You are not using cmd configuring, you are using config and pools file. You only added one parameter, there are a few you need to set. Please check the readme for examples on how to set up gpus in cmdline.
Or you have my example i gave.
Theres no mixing of config files and cmd parameters.

[swongsR1thing]

Is it normal for miner to do "precompilation" during mining?
I thought it only does precompiling before it starts mining.

[doktor83]

Is it normal for miner to do "precompilation" during mining?
I thought it only does precompiling before it starts mining.

It always does, it is doing it since CN/R was added, only that it wasn't displayed to the user earlier on the screen/log.

[IlyaVak]

Altcoinlog about  SRBMiner Miner



Official site and SRBMiner setup instructions. How to start mining Monero and possible installation problems. Ready Bat files for quick start.

The article is written in Russian.

https://altcoinlog.com/srbminer-cryptonight-amd-gpu-miner-v1-8/

[doktor83]

Altcoinlog about  SRBMiner Miner



Official site and SRBMiner setup instructions. How to start mining Monero and possible installation problems. Ready Bat files for quick start.

The article is written in Russian.

https://altcoinlog.com/srbminer-cryptonight-amd-gpu-miner-v1-8/

Wow, thank you very much!
The article is very helpful, it can help beginners with setting up the miner.

Thanks again Alina 

[flameelement]

Hello,

I've mine CN heavy with 570 4g.

Here is my config:
{"id" : 0, "intensity" : 29, "worksize" : 8, "threads" : 2, "fragment": 0, "tweak_profile": 1, "old_mode" : true},

Myner is 1-8-9 and I've set in bat file --adldisable --disablegpuwatchdog.

My OC through Overdrive tool is 1230 core at 930mv and 2030 mem at 930mv. The hash is 900+h/s and got 80 computing errors for 2 days of mining.

Can I squeeze more hashrate and how? Are my config good enough or need to change something?

Are the compute errors a problem and how to stop them?

Kind regards in advance!