hitmandn
Newbie
Offline
Activity: 35
Merit: 0
|
|
June 08, 2019, 12:13:52 PM Last edit: June 08, 2019, 03:00:36 PM by hitmandn |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem. --> which vram rx470, mod bios or stock bios.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?---- > i try 1.8.9 , 1.8.8 and 1.8.6 . Only cause when mining Monero, not cause with MSR before
-- i try "Radeon Software Crimson ReLive Edition Beta for Blockchain Compute Driver for Windows® 10 64-bit" and has issues about 1 hour. - (~ 9xx h/z) i try " 1.8.9....." with 4 steps ....you give. (~ 4xx h/z) My card used elpida and samsung ram. Could you try it help me http://www.mediafire.com/file/78j51aca1le46v5/Ellesmere-samsung.rom/filehttp://www.mediafire.com/file/yqii06b9ajyui35/Ellesmere-elpida.rom/file
|
|
|
|
doktor83 (OP)
|
|
June 08, 2019, 04:23:33 PM |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem. --> which vram rx470, mod bios or stock bios.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?---- > i try 1.8.9 , 1.8.8 and 1.8.6 . Only cause when mining Monero, not cause with MSR before
-- i try "Radeon Software Crimson ReLive Edition Beta for Blockchain Compute Driver for Windows® 10 64-bit" and has issues about 1 hour. - (~ 9xx h/z) i try " 1.8.9....." with 4 steps ....you give. (~ 4xx h/z) My card used elpida and samsung ram. Could you try it help me http://www.mediafire.com/file/78j51aca1le46v5/Ellesmere-samsung.rom/filehttp://www.mediafire.com/file/yqii06b9ajyui35/Ellesmere-elpida.rom/file Vram manufacturer and bios does not matter in this case. I really have no clue why it takes so much time on your rig to precompile, rx 470 4gb should not take more than 15-20 sec.
|
|
|
|
toptek12
Member
Offline
Activity: 125
Merit: 10
|
|
June 09, 2019, 01:06:07 AM |
|
does this miner support Radeon VII all I see is the hash rate no fan speed , temp etc i have to look at after burner for the temp etc. I got mine doing 3.01 kh . or is it a driver issue I'm using adrenalin-2019-edition-19.5.2-june3. using adrenalin-2019-edition-19.5.2-june3 drivers the rest of the rig hashes like it does with 18.6.1 .
|
|
|
|
hitmandn
Newbie
Offline
Activity: 35
Merit: 0
|
|
June 09, 2019, 02:26:29 AM |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem. --> which vram rx470, mod bios or stock bios.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?---- > i try 1.8.9 , 1.8.8 and 1.8.6 . Only cause when mining Monero, not cause with MSR before
-- i try "Radeon Software Crimson ReLive Edition Beta for Blockchain Compute Driver for Windows® 10 64-bit" and has issues about 1 hour. - (~ 9xx h/z) i try " 1.8.9....." with 4 steps ....you give. (~ 4xx h/z) My card used elpida and samsung ram. Could you try it help me http://www.mediafire.com/file/78j51aca1le46v5/Ellesmere-samsung.rom/filehttp://www.mediafire.com/file/yqii06b9ajyui35/Ellesmere-elpida.rom/file Vram manufacturer and bios does not matter in this case. I really have no clue why it takes so much time on your rig to precompile, rx 470 4gb should not take more than 15-20 sec. I have 54 card rx470, they have the same cause, hizzz. what coin precompile program your mining. I'will try mine it
|
|
|
|
ipp2
Newbie
Offline
Activity: 37
Merit: 0
|
|
June 09, 2019, 03:19:45 PM |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?
So one interesting thing about this is that it only occurs VERY occasionally. Once a day at most. I've got all kinda of polaris cards on my rigs and after your post Dok, I went ahead and tried the 18.6.1 drivers on a single rig. I got them to mine at full speed by having the 'Radeon settings' be installed and manually one by one setting compute mode (so painful). I can report back that it is the drivers. Blockchain drivers hang (doing so right now even) while 18.6.1 continues to work. Sorry for it taking so long to time to respond but the blockchain drivers did not fail for 4 days nearly! They just failed about 20 minutes prior to reporting this and still are while typing this. In fact I had time to start a new test rig with 1 card with 18.6.1 and it's working fine also. 5 rigs (with 6/7 cards each) What's interesting is when the BC drivers stall...it isn't a one time thing. They will stall through multiple blocks for up to an hour. Even if you reboot and start the script up again it will just not work and stall out. The popular pools don't matter, they all do the same issue. This points to not being a hardware issue at all. So I think it has something to do with blocks themselves. https://i.imgur.com/3VUWfLe.png
|
|
|
|
hitmandn
Newbie
Offline
Activity: 35
Merit: 0
|
|
June 09, 2019, 04:13:24 PM |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?
So one interesting thing about this is that it only occurs VERY occasionally. Once a day at most. I've got all kinda of polaris cards on my rigs and after your post Dok, I went ahead and tried the 18.6.1 drivers on a single rig. I got them to mine at full speed by having the 'Radeon settings' be installed and manually one by one setting compute mode (so painful). I can report back that it is the drivers. Blockchain drivers hang (doing so right now even) while 18.6.1 continues to work. Sorry for it taking so long to time to respond but the blockchain drivers did not fail for 4 days nearly! They just failed about 20 minutes prior to reporting this and still are while typing this. In fact I had time to start a new test rig with 1 card with 18.6.1 and it's working fine also. 5 rigs (with 6/7 cards each) What's interesting is when the BC drivers stall...it isn't a one time thing. They will stall through multiple blocks for up to an hour. Even if you reboot and start the script up again it will just not work and stall out. The popular pools don't matter, they all do the same issue. This points to not being a hardware issue at all. So I think it has something to do with blocks themselves. https://i.imgur.com/3VUWfLe.png Exactly, it's the same things, maybe BC has stuck at that time.....They just failed about 20 minutes prior to reporting too
|
|
|
|
Bojcha
|
|
June 09, 2019, 08:26:32 PM |
|
Random X
|
|
|
|
doktor83 (OP)
|
|
June 10, 2019, 08:57:15 AM |
|
I've got all kinda of polaris cards on my rigs and after your post Dok, I went ahead and tried the 18.6.1 drivers on a single rig. I got them to mine at full speed by having the 'Radeon settings' be installed and manually one by one setting compute mode (so painful).
I can report back that it is the drivers. Blockchain drivers hang (doing so right now even) while 18.6.1 continues to work. Sorry for it taking so long to time to respond but the blockchain drivers did not fail for 4 days nearly! They just failed about 20 minutes prior to reporting this and still are while typing this.
You don't need to go that painful road , don't install the whole AMD 18.6.1 driver suite, just the drivers, and after that run this in an admin elevated cmd prompt : SRBMiner-CN.exe --setcomputemode
It will set every AMD gpu in your system to compute mode. Or you can use the AMD-Compute-Mode-SwitcherAnyways, back to the driver installation. After doing the cleanup with DDU, run the AMD driver installer and wait until it gets to the screen where you can actually install it (it was unpacking data before that to c:\AMD). Close the window, don't install anything. Go to Device Manager , under Display Adapters you should see your GPU's not recognised (because no driver was installed). Right click on any -> update driver -> browse my computer for driver -> and the search location should be C:\AMD\Win10-64Bit-Radeon-Software-Adrenalin-Edition-18.6.1-June13\Packages\Drivers\Display\WT6A_INFThis will install the 18.6.1 drivers without all the other junk. After this patch the driver with Pixel Clock Patcher if needed. And set the GPU's to compute mode with the above described method. I am preparing for the next SRB version a parameter that can set the number of blocks that get precompiled, so maybe it will help someone reduce precompilation time..
|
|
|
|
MingMining
Member
Offline
Activity: 202
Merit: 10
Eloncoin.org - Mars, here we come!
|
|
June 11, 2019, 02:05:16 AM |
|
I have the same issue. Tried to reinstall the driver and the same result. The mb looks ok and everything runs and recognized. Any idea what is going on? Hello,
I'm knew to SRB miner and I'm having some difficulty. I followed instructions in the guide and can only manage to get.
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Times infinity. I'm using the generic guided set up with V1.8.9 and 8.6.1 for my vegas. I'm not sure what else to add, any advice?
Try reinstalling the drivers using DDU. Otherwise, it might be an indication of a faulty motherboard.
|
|
|
|
doktor83 (OP)
|
|
June 11, 2019, 11:54:25 AM |
|
I have the same issue. Tried to reinstall the driver and the same result. The mb looks ok and everything runs and recognized. Any idea what is going on? Hello,
I'm knew to SRB miner and I'm having some difficulty. I followed instructions in the guide and can only manage to get.
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Times infinity. I'm using the generic guided set up with V1.8.9 and 8.6.1 for my vegas. I'm not sure what else to add, any advice?
Try reinstalling the drivers using DDU. Otherwise, it might be an indication of a faulty motherboard. Show me your start.bat file
|
|
|
|
GodOfStars
Newbie
Offline
Activity: 49
Merit: 0
|
|
June 11, 2019, 01:19:12 PM |
|
Hi guys is there anyone getting 2120-2200 hashes on Vega 64 on the latest SRB Miner consuming less than 185Watts for a card from the wall?
|
|
|
|
hitmandn
Newbie
Offline
Activity: 35
Merit: 0
|
|
June 11, 2019, 05:03:43 PM |
|
@hitmand @ipp2
i switched 18.6.1 drivers on a 470 4/8g mixed rig to the blockchain drivers to see if that's causing some issues with the 'invalid job' and @hitmand's 3 minute / gpu precompile time, but no - all should be fine with BC drivers, so at least now i know its not the driver that is making the problem.
Can you guys tell me which SRB version are you using? I see @hitmand uses 1.8.8 , have you tried 1.8.9 ? Are you mining monero or some other CN/R coin ?
So one interesting thing about this is that it only occurs VERY occasionally. Once a day at most. I've got all kinda of polaris cards on my rigs and after your post Dok, I went ahead and tried the 18.6.1 drivers on a single rig. I got them to mine at full speed by having the 'Radeon settings' be installed and manually one by one setting compute mode (so painful). I can report back that it is the drivers. Blockchain drivers hang (doing so right now even) while 18.6.1 continues to work. Sorry for it taking so long to time to respond but the blockchain drivers did not fail for 4 days nearly! They just failed about 20 minutes prior to reporting this and still are while typing this. In fact I had time to start a new test rig with 1 card with 18.6.1 and it's working fine also. 5 rigs (with 6/7 cards each) What's interesting is when the BC drivers stall...it isn't a one time thing. They will stall through multiple blocks for up to an hour. Even if you reboot and start the script up again it will just not work and stall out. The popular pools don't matter, they all do the same issue. This points to not being a hardware issue at all. So I think it has something to do with blocks themselves. https://i.imgur.com/3VUWfLe.png Exactly, it's the same things, maybe BC has stuck at that time.....They just failed about 20 minutes prior to reporting tooWhy it's always cause in precompiling program http://s1251.photobucket.com/user/hitmandn/media/Capture_1.png.html?sort=3&o=0
|
|
|
|
doktor83 (OP)
|
|
June 11, 2019, 05:07:34 PM |
|
Im not surprised you got stale shares, holy cr**, 8 minutes to precompile 15 blocks?! Please upload the logfile somewhere and send me the link in pm
|
|
|
|
NCarter84
Jr. Member
Offline
Activity: 195
Merit: 4
|
|
June 11, 2019, 11:52:44 PM |
|
Anyone know a coin that is using the old swap algo? Believe it was renamed "Super Fast".
|
|
|
|
MingMining
Member
Offline
Activity: 202
Merit: 10
Eloncoin.org - Mars, here we come!
|
|
June 12, 2019, 12:43:28 AM |
|
Hi Doc, here is the start.bat file. setx GPU_MAX_HEAP_SIZE 100 setx GPU_MAX_USE_SYNC_OBJECTS 1 setx GPU_SINGLE_ALLOC_PERCENT 100 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_MAX_SINGLE_ALLOC_PERCENT 100 @echo off cd %~dp0 cls for /f "tokens=2 delims==" %%a in ('wmic OS Get localdatetime /value') do set "dt=%%a" set LOGTIME=%dt:~0,4%_%dt:~4,2%_%dt:~6,2%_%dt:~8,2%_%dt:~10,2%_%dt:~12,2% set LOGTIME=%LOGTIME: =% set LOGTIME=%LOGTIME:,=.%.txt SRBMiner-CN.exe --enablecoinforking --config Config\config-litev7.txt --pools pools.txt --logfile %LOGTIME% I have the same issue. Tried to reinstall the driver and the same result. The mb looks ok and everything runs and recognized. Any idea what is going on? Hello,
I'm knew to SRB miner and I'm having some difficulty. I followed instructions in the guide and can only manage to get.
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Enumerating OpenCL devices, please wait...
Restarting miner...
Times infinity. I'm using the generic guided set up with V1.8.9 and 8.6.1 for my vegas. I'm not sure what else to add, any advice?
Try reinstalling the drivers using DDU. Otherwise, it might be an indication of a faulty motherboard. Show me your start.bat file
|
|
|
|
|
doktor83 (OP)
|
|
June 12, 2019, 05:24:10 AM |
|
I can't open it says the archive is broken, and why is it 45mb ?
|
|
|
|
doktor83 (OP)
|
|
June 12, 2019, 05:26:14 AM |
|
SRBMiner-CN.exe --enablecoinforking --config Config\config-litev7.txt --pools pools.txt --logfile %LOGTIME%
Try without the --enablecoinforking parameter, maybe that's causing the issue.
|
|
|
|
MingMining
Member
Offline
Activity: 202
Merit: 10
Eloncoin.org - Mars, here we come!
|
|
June 12, 2019, 05:36:22 AM |
|
Thanks Doc. It has been working for weeks. Yesterday it stopped working and I rebooted the box. The miner started to be like that. My other miners are using the same software and same config. All are just fine. SRBMiner-CN.exe --enablecoinforking --config Config\config-litev7.txt --pools pools.txt --logfile %LOGTIME%
Try without the --enablecoinforking parameter, maybe that's causing the issue.
|
|
|
|
issie81
|
|
June 12, 2019, 06:06:08 AM |
|
i cant seem to get miners stable at --cgputweakprofile 4,4,4,4,4 Only half seem stable (i am not on facility maybe just need to reboot or so i am using Awesome Miner)
i choose low value because default my hashrate is around 1.85Kh/s for CN R, which i think Vega should do atleast 2Kh/s
my startup commando is
--ccryptonighttype normalv4 --cgpuid 0,1,2,3,4 --cgpuworksize 16,16,16,16,16 --cgpuintensity 112,112,112,112,112 --cgputhreads 2,2,2,2,2 --cgputweakprofile 4,4,4,4,4
and use OverdriveNtools
core 1450/900 mem 935/900
are some settings off are am i missing a point/setting here?
|
|
|
|
|