|
sacskate
|
 |
March 02, 2014, 12:52:48 AM |
|
I know people here hate altcoins. But no one else can answer my questions. I have Btmine avalon clone. I have actually roi'ed it with sha altcoins. Currently I have to use pools for my avalon. I would love to be able to solo mine sha alt coins with it. I have the ip of my miner in my .conf for the wallet but it still does not connect. I've heard that it's basically impossible to solo sha altcoins with an avalon. Is this correct?
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
ManeBjorn
Legendary
 Offline
Activity: 1288
Merit: 1004
|
|
March 02, 2014, 03:06:20 AM |
|
You could try Peercoin or some of the others that have lower total difficulties. Here is a good list of SHA coins that it should be able to mine. https://cryptocointalk.com/forum/179-sha-256-cryptocoins/Check them out and see how they are doing in the exchanges then decide a couple and try them out. I hope it helps you out. I know people here hate altcoins. But no one else can answer my questions. I have Btmine avalon clone. I have actually roi'ed it with sha altcoins. Currently I have to use pools for my avalon. I would love to be able to solo mine sha alt coins with it. I have the ip of my miner in my .conf for the wallet but it still does not connect. I've heard that it's basically impossible to solo sha altcoins with an avalon. Is this correct?
|
|
|
|
|
sacskate
|
|
March 02, 2014, 03:21:56 AM |
|
I have been very careful. I run the wallets on a pc that has nothing on it anyway. My question was though, how would I solo mine these coins from the avalon clone. I put rpcallowip=thewalletsip in the config for the coin, but the miner will not connect to the wallet. I've opened the ports on my router. I've done rather well mining alts, it just sucks that I always find over double the blocks for the pools as I actually get paid out, and would love to solo.
|
|
|
|
|
ProfMac
Legendary
Offline
Activity: 1246
Merit: 1001
|
|
March 02, 2014, 03:22:38 AM |
|
I know people here hate altcoins. But no one else can answer my questions. I have Btmine avalon clone. I have actually roi'ed it with sha altcoins. Currently I have to use pools for my avalon. I would love to be able to solo mine sha alt coins with it. I have the ip of my miner in my .conf for the wallet but it still does not connect. I've heard that it's basically impossible to solo sha altcoins with an avalon. Is this correct?
Most of the wallets don't support stratum mining, and the Avalons hash too fast. You will need to download Stratum software to pass work from your wallet to your miner. Many altcoins do have stratum pools already set up. |
I try to be respectful and informed.
|
|
|
|
gjpminingco
|
|
March 02, 2014, 03:26:27 AM |
|
Hey also rpcallowip= is for the IP of your miner not the wallet since that option is in the config file of the wallet
|
|
|
|
|
gjpminingco
|
|
March 02, 2014, 03:27:37 AM |
|
sacskate if you would like i can setup everything for ya, any tips would be appreciated
|
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 02, 2014, 03:33:23 AM |
|
I would run MultiMiner and use it's as a stratum. From there you can setup to mine on pools and even solo mine. The easy to use GUI makes setup easy and nwools supports it solidly answering questions right on here in this thread. https://bitcointalk.org/index.php?topic=248173.0I have been very careful. I run the wallets on a pc that has nothing on it anyway. My question was though, how would I solo mine these coins from the avalon clone. I put rpcallowip=thewalletsip in the config for the coin, but the miner will not connect to the wallet. I've opened the ports on my router. I've done rather well mining alts, it just sucks that I always find over double the blocks for the pools as I actually get paid out, and would love to solo.
|
|
|
|
|
sacskate
|
|
March 02, 2014, 03:37:36 AM
Last edit: March 02, 2014, 04:04:33 AM by sacskate |
|
Will check into multi miner. I meant the ip of the miner. I mine scrypt with gpus solo with wallets on different pc's with no problem. I'll try multi miner and report back, thanks for the help!
Edit: I don't think multi miner will help as I cannot install it on the avalon. It is a stand alone unit. It has cgminer installed on it. I did mange to get the avalon to connect to my wallet, but cgminer shows no hashrate and all getworks.
|
|
|
|
|
|
smoothrunnings
|
|
March 02, 2014, 04:24:24 AM |
|
I know people here hate altcoins. But no one else can answer my questions. I have Btmine avalon clone. I have actually roi'ed it with sha altcoins. Currently I have to use pools for my avalon. I would love to be able to solo mine sha alt coins with it. I have the ip of my miner in my .conf for the wallet but it still does not connect. I've heard that it's basically impossible to solo sha altcoins with an avalon. Is this correct?
What are you using P2Pool? If so ask in the P2Pool mining -> Pool forum for help. |
|
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 02, 2014, 06:03:38 AM |
|
With MultiMiner you setup a stratum proxy that will allow you to point the Avalon at the pool of your choice or possibly solo mine. Ask on the MultiMiner thread as many people there can help you get going. Plus as was said before if you check on the P2Pool threads you will get lots of help doing what you want as well. Will check into multi miner. I meant the ip of the miner. I mine scrypt with gpus solo with wallets on different pc's with no problem. I'll try multi miner and report back, thanks for the help!
Edit: I don't think multi miner will help as I cannot install it on the avalon. It is a stand alone unit. It has cgminer installed on it. I did mange to get the avalon to connect to my wallet, but cgminer shows no hashrate and all getworks.
|
|
|
|
|
|
-ck
Legendary
Offline
Activity: 4088
Merit: 1631
Ruu \o/
|
|
March 05, 2014, 04:29:55 AM |
|
Did you miss the part where i offered firmware? http://ck.kolivas.org/apps/cgminer/avalon/20140228/Admittedly it was blindly built, but one user tried it and it was fine. |
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel
2% Fee Solo mining at solo.ckpool.org
-ck
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 06:39:01 AM |
|
How does it work? Does it give any improvements in performance and stability?? |
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 06:40:19 AM |
|
How has it been running for you? I am ready to try it but I wanted to see how it was doing for others for a bit first. Have you seen any improvements and such? What are the new features? |
|
|
|
|
gjpminingco
|
|
March 05, 2014, 07:06:46 AM |
|
I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
|
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 07:11:24 AM |
|
I updated and all I get is this error. [Firmware Version] => 20140227
cgminer:
cgminer-openwrt-packages: bb677a2+
luci: d2fe67a
Socket connect failed: Connection refused I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
|
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 07:11:55 AM |
|
I cannot get it to connect at all. I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
|
|
|
|
|
gjpminingco
|
|
March 05, 2014, 07:16:52 AM |
|
I cannot get it to connect at all. I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
If you want help i can help you do you have Teamviewer? |
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 07:24:46 AM |
|
No I don't but I can get it if you give me a min? I cannot get it to connect at all. I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
If you want help i can help you do you have Teamviewer? |
|
|
|
ManeBjorn
Legendary
Offline
Activity: 1288
Merit: 1004
|
|
March 05, 2014, 07:30:20 AM |
|
Thanks for the help I sent you a PM for team viewer. I cannot get it to connect at all. I have had mine running on the one i built for the 110nm chip for a few days I did notice that running at Freq of 375 I got more HW errors but dropping down to 35 DRASTICALLY loweredmy error rate and with the new firmware i got a speed boost when running on CEX
If you want i will post the settings i run
If you want help i can help you do you have Teamviewer? |
|
|
|
|
