Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[gribgo]

Hi! I want to poolmine ETH and solo-mine for SIA, But how to do mining with 4 rigs to the one wallet for solo?
In the onther words do I have to bother pointing all rigs at one Sia wallet or just start the separate deamon at every rig?
Also What if any of my rigs go offline for any reason and the block was not yet found.. does it mean I have lost all work done it will impact solomining in any negative ways?

Thank you!
peace

[scryptr]

Hi! I want to poolmine ETH and solo-mine for SIA, But how to do mining with 4 rigs to the one wallet for solo?
In the onther words do I have to bother pointing all rigs at one Sia wallet or just start the separate deamon at every rig?
Also What if any of my rigs go offline for any reason and the block was not yet found.. does it mean I have lost all work done it will impact solomining in any negative ways?

Thank you!
peace

ONE SIA WALLET FOR YOUR LAN--

Point all of your rigs to a single LAN address where the wallet is installed.  That will combine all your hash, and decrease the Time-To-Find (TTF) a Sia block.  Now, if you install multiple wallets, one per rig, it still works. It just seems more complicated.

Your choice.  If your rigs are not stable, multiple wallets may be a better bet.

[xurious]

Hi! I want to poolmine ETH and solo-mine for SIA, But how to do mining with 4 rigs to the one wallet for solo?
In the onther words do I have to bother pointing all rigs at one Sia wallet or just start the separate deamon at every rig?
Also What if any of my rigs go offline for any reason and the block was not yet found.. does it mean I have lost all work done it will impact solomining in any negative ways?

Thank you!
peace

ONE SIA WALLET FOR YOUR LAN--

Point all of your rigs to a single LAN address where the wallet is installed.  That will combine all your hash, and decrease the Time-To-Find (TTF) a Sia block.  Now, if you install multiple wallets, one per rig, it still works. It just seems more complicated.

Your choice.  If your rigs are not stable, multiple wallets may be a better bet.

As a word of warning, solomining for Sia while dual mining is going to give you a VERY high TTF. If you are hashing at 2GH/s with Sia, your average TTF is 45 days. With some bad luck, you could go months without finding a block, and not getting paid during that time.

[fittsy]

with remote manager, the applied settings from config.txt should apply automatically? no miner restart or anything needed?
Somehow this function doesnt work for me, just says in miner window that config.txt has been applied but nothing changes.

If you send a new config file using the remote manager I believe you need to restart miner to apply the new config settings.

@BenSF is correct.

When you update your config.txt using the remote manager you need to restart the miner for settings to take effect.  Claymore miner only reads the config file when the miner starts. That's why there is a "restart miner" option in the remote manager.

[prichina]

Pls make a stratum for SIA , Mr. Claymore sir.

[gary_aut]

First of all, thank you for the great Miner, Claymore.

Anybody tried the CDM working with parity Node ?

I always got following error when i send rpc request via CDM. When i fill in the Request in the Web Frontend it works.

Code:

09:33:49:860	19c8	commandline: EthDcrMiner64.exe  -epool http://192.168.1.78:8545 -allcoins 1
09:33:49:864	19c8	
09:33:49:870	19c8	ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
09:33:49:877	19c8	º      Claymore's Dual ETH + DCR/SC AMD GPU Miner v5.0 Beta      º
09:33:49:882	19c8	ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
09:33:49:887	19c8	
09:33:50:095	19c8	ETH: 1 pool is specified
09:33:50:100	19c8	Main Ethereum pool is 192.168.1.78:8545
09:33:50:107	19c8	DCR: 0 pool is specified
09:33:51:233	19c8	OpenCL platform: Intel(R) OpenCL
09:33:51:236	19c8	OpenCL platform: AMD Accelerated Parallel Processing
09:33:51:239	19c8	
Cards available: 6 
09:33:51:243	19c8	GPU #0: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:246	19c8	GPU #1: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:250	19c8	GPU #2: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:253	19c8	GPU #3: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:265	19c8	GPU #4: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:269	19c8	GPU #5: name: Hawaii, 8192 MB available, 40 compute units 
09:33:51:273	19c8	Total cards: 6 
09:33:51:280	19c8	Initializing...

09:33:51:283	19c8	GPU #0 recognized as Radeon 390
09:33:51:286	19c8	GPU #1 recognized as Radeon 390
09:33:51:290	19c8	GPU #2 recognized as Radeon 390
09:33:51:316	19c8	GPU #3 recognized as Radeon 390
09:33:51:324	19c8	GPU #4 recognized as Radeon 390
09:33:51:328	19c8	GPU #5 recognized as Radeon 390
09:33:51:332	19c8	POOL/SOLO version
09:33:51:335	19c8	b167 
09:33:51:345	19c8	start building OpenCL program...
09:33:53:093	19c8	done
09:33:53:097	19c8	GPU #0: set -etha as 0 (ETH algo for fast cards)
09:33:53:104	19c8	GPU #1: set -etha as 0 (ETH algo for fast cards)
09:33:53:110	19c8	GPU #2: set -etha as 0 (ETH algo for fast cards)
09:33:53:121	19c8	GPU #3: set -etha as 0 (ETH algo for fast cards)
09:33:53:125	19c8	GPU #4: set -etha as 0 (ETH algo for fast cards)
09:33:53:130	19c8	GPU #5: set -etha as 0 (ETH algo for fast cards)
09:33:53:322	b58	ETH - connecting to 192.168.1.78:8545
09:33:53:325	b58	http send request: {"method": "eth_getWork", "params": [], "id":0}
09:33:53:330	b58	http got answer: {"jsonrpc":"2.0","error":{"code":-32600,"message":"Invalid request","data":null},"id":null}

09:33:53:335	b58	ETH: Connected (192.168.1.78:8545)
09:33:53:338	b58	parse packet: 91
09:33:53:343	b58	ETH: Received error: {"jsonrpc":"2.0","error":{"code":-32600,"message":"Invalid request","data":null},"id":null}

09:33:53:347	b58	new buf size: 0
09:33:53:421	19c8	No pool specified for Decred! Ethereum-only mining mode is enabled

09:33:53:427	19c8	ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)

09:33:53:434	19c8	ETH: HTTP SOLO mode
09:33:53:438	19c8	Ethereum HTTP requests time (-etht) is set to 200 ms

09:33:53:455	19c8	"-allcoins" option is set, default pools will be used for devfee, check "Readme" file for details.
09:33:53:463	19c8	Watchdog enabled
09:33:53:467	19c8	Remote management is enabled on port 3333
09:33:53:471	19c8	

Thank you for your help 

[hasher87]

I've been searching through this post on how to run claymore on miningrigrentals, but somehow i couldn't find any of the post that is helpful.

this is the code that i've used

Code:

EthDcrMiner64.exe -epool ap-01.miningrigrentals.com:3333 -ewal hasher87.30677 -epsw x -eworker rig1 -allpools 1

and below is what i got

Code:

GPU #0 recognized as Radeon RX 480
GPU #1 recognized as Radeon RX 480
POOL/SOLO version
GPU #0: set -etha as 0 (ETH algo for fast cards)
GPU #1: set -etha as 0 (ETH algo for fast cards)
ETH: Stratum - connecting to 'ap-01.miningrigrentals.com' <128.199.138.106> port 3333
ETH: Stratum - Connected (ap-01.miningrigrentals.com:3333)
No pool specified for Decred! Ethereum-only mining mode is enabled
ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)
ETH: eth-proxy stratum mode
"-allpools" option is set, default pools can be used for devfee, check "Readme" file for details.
Watchdog enabled
Remote management is enabled on port 3333

ETH: Job timeout, disconnect, retry in 20 sec...

appreciate if someone has the solutions to it

try to change -esm value with 1, 2 or 3.

-esm   Ethereum Stratum mode. 0 - eth-proxy mode (for example, dwarpool.com), 1 - qtminer mode (for example, ethpool.org),
   2 - miner-proxy mode (for example, coinotron.com), 3 - nicehash mode. 0 is default.

and add -mode 1 to disable decred dual mining as you seem not to use it.

tried out accordingly, but this is what i got so far,

Code:

18:11:29:585	11e8	GPU #0: set -etha as 0 (ETH algo for fast cards)
18:11:29:588	11e8	GPU #1: set -etha as 0 (ETH algo for fast cards)
18:11:29:708	830	ETH: Stratum - connecting to 'ap-01.miningrigrentals.com' <128.199.138.106> port 3333
18:11:29:728	11e8	ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)

18:11:29:734	11e8	ETH: qtminer stratum mode
18:11:29:743	830	send: {"id":2,"jsonrpc":"2.0","method":"eth_login","params":["hasher87.30677","x"]}

18:11:29:744	11e8	"-allpools" option is set, default pools can be used for devfee, check "Readme" file for details.
18:11:29:756	830	ETH: Stratum - Connected (ap-01.miningrigrentals.com:3333)
18:11:29:762	11e8	Watchdog enabled
18:11:29:769	11e8	Remote management is enabled on port 3333
18:11:29:774	11e8	

18:11:32:785	11e8	Unsupported Overdrive version 7 
18:11:33:073	830	checkread timeout
18:11:35:794	11e8	Unsupported Overdrive version 7 
18:11:36:394	830	checkread timeout
18:11:38:800	11e8	Unsupported Overdrive version 7 
18:11:39:710	830	checkread timeout
18:11:41:808	11e8	Unsupported Overdrive version 7 
18:11:43:031	830	checkread timeout
18:11:44:814	11e8	Unsupported Overdrive version 7 
18:11:46:352	830	checkread timeout
18:11:47:821	11e8	Unsupported Overdrive version 7 
18:11:49:673	830	checkread timeout
18:11:50:831	11e8	Unsupported Overdrive version 7 
18:11:52:990	830	checkread timeout
18:11:53:843	11e8	Unsupported Overdrive version 7 
18:11:56:309	830	checkread timeout
18:11:56:853	11e8	Unsupported Overdrive version 7 
18:11:59:630	830	checkread timeout
18:11:59:868	11e8	Unsupported Overdrive version 7 
18:11:59:881	11e8	Unsupported Overdrive version 7 
18:11:59:890	11e8	em hbt: 30266, fm hbt: 94, 
18:11:59:899	11e8	watchdog - thread 0, hb time 63
18:11:59:908	11e8	watchdog - thread 1, hb time 63
18:11:59:917	11e8	watchdog - thread 2, hb time 63
18:11:59:926	11e8	watchdog - thread 3, hb time 63
18:12:02:936	11e8	Unsupported Overdrive version 7 
18:12:02:946	830	checkread timeout
18:12:02:957	830	ETH: Job timeout, disconnect, retry in 20 sec...

While it does that, my MRR did detect the connectivity, as i received notification soon that my rig is offline, however it doesnt do any hashing

[ivanpop]

How do you use remote management? I have remote management enabled, I've installed Claymore's Dual Miner Monitor on my phone and I can see hashrates and temperatures. However, if I type the rig's ip and port in a browser, I don't get anything. How can I manage my rig remotely?
Also can this mobile app notify you if the rig has stopped mining for some reason?

[wpsd]

How do you use remote management? I have remote management enabled, I've installed Claymore's Dual Miner Monitor on my phone and I can see hashrates and temperatures. However, if I type the rig's ip and port in a browser, I don't get anything. How can I manage my rig remotely?
Also can this mobile app notify you if the rig has stopped mining for some reason?

The remote management is a raw socket server, not web server. there is no web gui so you cannot access it from browser.
In Windows you need to use EthMon.exe provided in the folder inside claymore
In Linux you can run it also under wine it works ok.
You can also write your own client  it use json format

[sammy007]

Is there any kernel performance optimization since 4.7?

[Bakery]

How do you use remote management? I have remote management enabled, I've installed Claymore's Dual Miner Monitor on my phone and I can see hashrates and temperatures. However, if I type the rig's ip and port in a browser, I don't get anything. How can I manage my rig remotely?
Also can this mobile app notify you if the rig has stopped mining for some reason?

The remote management is a raw socket server, not web server. there is no web gui so you cannot access it from browser.
In Windows you need to use EthMon.exe provided in the folder inside claymore
In Linux you can run it also under wine it works ok.
You can also write your own client  it use json format

As I understand it's not possible to access miners from external networks? i.e I have to be connected to local network, right? I just can't fill the boxes with my ipv6 address and watch miners?

[ivanpop]

You can do port forwarding inside your router and open port 3333, but this way it will be accessible to everyone and you should disable management, only monitoring.

[Ichskill]

Should i buy r9 390s or rx 480s ?

[ivanpop]

480s

[ps_jb]

Should i buy r9 390s or rx 480s ?

r9 390

[hasher87]

Should i buy r9 390s or rx 480s ?

Im running on 480 crossfire. So far its pretty good.

Card 1 runs at 25Mh/s (due to dual monitor connected, one of it is 4k reso)

Card 2 runs at 27.5Mh/s

[Pilasu]

Hi all. Someone mining on gtx 960? i get only 1,7 mhs   Should be 10.

[fredeq]

Mining ETH or ETC?
https://poloniex.com/exchange#btc_etc

[Hagmonar]

Mining ETH or ETC?

Mining ETC is more profitable at the moment. But if there is some kind of 51% attack, it will become unprofitable.

[restless]

One of my cards from time to time get as hot as 80C
As i want to keep all cards under 80, i use -tstop 80
But ones the card reaches 80, its stopped from miner and never returned to mining.
is there a way to auto-restart it? or I should just use higher value for tstop?
Or simply restart the miner from time to time (say -r 60 )