PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[peterboy1]

what the fuck is wrong with these people posting whole log content? you deserve to have lots of problems.

I just don´t know which row of text could provide clues for more experienced people to solve that issue.

you could just insert it like this:

Code:

a
s
d
f
g
s
s
d
f
d
s
d
f
f
g
d
s
s
d
d
f
f
f
d
d
f
f
f
f
d

so that its scrollable

[johnfoxh]

a few hours back pool shows that rig went offline but the miner still submit shares.
i've restarted the miner and still submit shares as usual but pool still doesn't show that.
been in touch with ethermine support but they insist that it wasn't a server side fault. still not sure if it was a pool or miner issue but till then, i'll continue using claymore.

[NN900]

Tried to use phoenix miner for the first time today, got 0,00 MHS for some reason

17604:04:37:09.590: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)

17604:04:37:30.157: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)
BAT: -pool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -wal nicehashwallet -pass x -proto 4 -stales 0 -amd

any ideas appreciated!

OK guys, I have found a solution - you have to disable GPU0 from device manager and start miner with 5 cards instead of 6.

[nitrobg]

Tried to use phoenix miner for the first time today, got 0,00 MHS for some reason

17604:04:37:09.590: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)

17604:04:37:30.157: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)
BAT: -pool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -wal nicehashwallet -pass x -proto 4 -stales 0 -amd

any ideas appreciated!

OK guys, I have found a solution - you have to disable GPU0 from device manager and start miner with 5 cards instead of 6.

You need either a monitor connected to the x16 GPU, an HDMI dummy plug, or use the iGPU of the motherboard. RX cards don't work on some motherboards without a monitor connected to the first card.

[NN900]

Tried to use phoenix miner for the first time today, got 0,00 MHS for some reason

17604:04:37:09.590: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)

17604:04:37:30.157: main GPUs: 1: 0.000 MH/s (0) 2: 0.000 MH/s (0) 3: 0.000 MH/s (0) 4: 0.000 MH/s (0) 5: 0.000 MH/s (0) 6: 0.000 MH/s (0)
BAT: -pool stratum+tcp://daggerhashimoto.eu.nicehash.com:3353 -wal nicehashwallet -pass x -proto 4 -stales 0 -amd

any ideas appreciated!

OK guys, I have found a solution - you have to disable GPU0 from device manager and start miner with 5 cards instead of 6.

You need either a monitor connected to the x16 GPU, an HDMI dummy plug, or use the iGPU of the motherboard. RX cards don't work on some motherboards without a monitor connected to the first card.

Thanks a lot, I will try!

[Digital_Seytan]

error 999 mostly with afterburner to high

[cryptoillusion1]

Too high memory overclock makes all readings on GPU-Z or similar programs return no data. Restart the rig, check which GPU returns no temperature, dial down the overclock and try again.
Phoenix is slightly more intensive compared to Claymore with default intensity, so if you are on the edge of stability on Claymore - it might crash with Phoenix.

Phoenix 2.7c crashes with the settings I have and with so many GPU's it will take lot of time to re-tune the clocks to match this program

Similar problem with claymore 11.2 to 11.4 but now Claymore has just released v11.5 with -oldkernel option which can be used in cases where they have problems with latest versions because they use hard OC and/or custom bioses created for old versions

any chance we can get a similar one for Phoenix so that there will not be need to change clock settings/bios mod

[nitrobg]

Too high memory overclock makes all readings on GPU-Z or similar programs return no data. Restart the rig, check which GPU returns no temperature, dial down the overclock and try again.
Phoenix is slightly more intensive compared to Claymore with default intensity, so if you are on the edge of stability on Claymore - it might crash with Phoenix.

Phoenix 2.7c crashes with the settings I have and with so many GPU's it will take lot of time to re-tune the clocks to match this program

Similar problem with claymore 11.2 to 11.4 but now Claymore has just released v11.5 with -oldkernel option which can be used in cases where they have problems with latest versions because they use hard OC and/or custom bioses created for old versions

any chance we can get a similar one for Phoenix so that there will not be need to change clock settings/bios mod

Drop the memory clock of all cards by 20MHz and try again. Not so hard.
Or just check the logs to see which GPU gives the temp error and reduce its clock.

[themurph2k]

Potential fix for the "debugger detected" error:

All I did was uninstall the AMD Aug23 BETA blockchain drivers and install the latest AMD Adrenaline drivers (18.3.1), switched GPUs to compute mode, OC as normal, and that fixed the "debugger detected" problem.

Getting +1.8Mh/s over latest Claymore.

Very happy.

[chain green]

Too high memory overclock makes all readings on GPU-Z or similar programs return no data. Restart the rig, check which GPU returns no temperature, dial down the overclock and try again.
Phoenix is slightly more intensive compared to Claymore with default intensity, so if you are on the edge of stability on Claymore - it might crash with Phoenix.

Tried even a bit more than -20 on memory.
Getting this error:
wdog Hardware manager thread not responding
wdog Thread(s) not responding. Restarting.

[kkanoee]

I have a weird thing, when mining PIRL I have 29mh/s but when I try to mine ETH Im getting 18mh/s. I tried ethermine and nanopool but nothing changed. Anyone got an idea ? I should get the same speed since its the same algorithm right ?

[plastkort]

would it be possible to get a fresh compiled version straight from the owen, or is it possible to get the source code so i can compile myself?

i need a fresh version because i allways get problems with precompiled binaries and AV.

[skinnyfalcon]

I have a weird thing, when mining PIRL I have 29mh/s but when I try to mine ETH Im getting 18mh/s. I tried ethermine and nanopool but nothing changed. Anyone got an idea ? I should get the same speed since its the same algorithm right ?

No, your hash rate will depend on the difficulty for a particular coin, Eth difficulty is way up there with BTC and LTC. Look at the difficulty level of Pirl compared to Eth.

[heavyarms1912]

I have a weird thing, when mining PIRL I have 29mh/s but when I try to mine ETH Im getting 18mh/s. I tried ethermine and nanopool but nothing changed. Anyone got an idea ? I should get the same speed since its the same algorithm right ?

No, your hash rate will depend on the difficulty for a particular coin, Eth difficulty is way up there with BTC and LTC. Look at the difficulty level of Pirl compared to Eth.

difficulty of the coin has nothing to do with the hashrate for algo.  PIRL and ETH both use dagger-hashimoto

@kkanoee which card is it?  Most likely you've some settings messed up

[john1010]

Can I mine other eth base coin, coz i tried to mine DBIX but it says that disconnecting to server... Am I missing something in my configuration?

My sample bat config..

PhoenixMiner.exe -pool stratum+tcp://beta-dbix.pool.sexy:10032 -wal 0xabc0419ec201fdccf5********* -epsw x -tt 65 -fanmin 55 -fanmax 90 -cclock 1130,1167,1130,1130,1130,1167,1167,1167,1167,1167,1167,1130 -mclock 2050,2100,2050,2050,2050,2100,2100,2100,2100,2100,2100,2050 -cvddc 850,820,850,850,850,820,820,820,820,820,820,850 -mvddc 850,820,850,850,850,820,820,820,820,820,820,850

[khafan11]

perfect , good job
switch claymore v11.4 to PhoenixMiner 2.7c 

[smallbitmoney]

Hi there,

Being using Claymore and had a steady hash rate at 243.5 Mh/s. Switched to PhoenixMiner 2.7c but hash rate fluctuates between 239+ to 248+ Mh/s; pool report an average of 242.4 M/hs. Does anyone hash rate fluctuates or it is just me?

[peeshypow]

So far so good...

I have double digit rigs with different card setups, I have not tried Phoenix Miner on any of those yet.  However I did try it on my test single GPU test machine.  It is right now a solo GTX 1070.  It was getting 29 to 30 mhs consistently at 62C on Claymore 11.2, rarely get stale shares with this card.

I started testing Phoenix Miner an hour ago.  I am getting 30 to 31 mhs.  It seems stable, same 62C.  However it seems my Effective speed is lower with Phoenix Miner at ethmine.   Then I noticed that in the short DEVFEE transition, it found 2 shares for the Devs while in the first 30 minutes it found just 6 for me.  So my effective rate(the actual rate measured by how many shares I find) at the pool is still 22.71 mh/s, but after a couple hours I will see if it catches up.  With Claymore my effective hash rate is pretty close and sometimes more than reported hash rate at the actual pool.

Overall it seems stable and if this small 0.5 mhs difference in speed on this one card is legit AND the dev fee is really legit then this looks like a possible better alternative to Claymore.

[kkanoee]

@kkanoee which card is it?  Most likely you've some settings messed up

RX580 8G Armor. some settings in the bat file you mean ?

[human75]

Hi Guys.
i am very happy with Phoenix Miner so far but i am having strange issue with Afterburner...i have Rx570 and 580 in my rig and in total 8 cards installed.Afterburner works perfect with old blockchain driver but when i installed latest adrenalin driver afterburner wont recognize my cards at all.all cards are good in windows device manager.Any advise?