PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[fomkas]

373 epoch almost killed me ... but everything seems to be alive again ...
ps RX570 4gb

Yours should work until EPOCH 379, maybe 380, however 381 will definately not work. If you are getting issues now then you are most likely not using onboard graphics as the main GPU in Linux. Basically go to your motherboard bios and enable onboard graphics, they will usually be automatically disabled and plug your monitor into the motherboards DVI connector and disconnect from the GPU.

Then try again and it should work. You can also use the -benchmark setting and try different DAG numbers and you will know exactly when it will stop to work for you. You pretty much got a month or so to go. After that you need to either upgrade the GPUs or use another software like lolminer which can mine after 4GB at reduced speeds.

i'am on windows)))) ... i wait when all juice down from windows....

[Binary100100]

don't trust anyone, check the information yourself

Noted. Thanks for the advice.
(Reported)

[UnclWish]

Anyone know if this is any better than the OhGodAnETHlargementPill?

Don't use it, it's scam.

[Wolfie]

Hey man -

Would you be so kind as to look into adding support for ProgPow-Epic ,

$EPIC = Epic Cash, 3 algo MW coin, 21mill supply, great little project

With all the 4GB cards available, we need some decent work for them.

Here is their GitLab link :

https://gitlab.com/epiccash

SRBminer already supports them RandomX\CPU,

TTminer already support them on ProgPOW\nVidia

thx in advance for anything you can do

Phoenix miner is only for ethereum algos.

How does it do ProgPOW for BCi?


from page 1:


PhoenixMiner also supports Ubqhash for mining UBQ, ProgPOW for mining BCI,  . . .

the mod should be simple, the EPIC ProgPOW just need to interpolate the pause when it algo switches

[bobalazs]

Epoch #385 on ETC

There is now hashrate drop under windows in 4 gb cards.

[reisdaddy]

Need help guys,

My MSI Radeon RX 5700 XT Gaming with this setting 5.1c:

Code:

-acm -clKernel 1 -clNew 1 -clf 0 ^
-gt 126 -cclock 1300 -cvddc 750 -mclock 900 ^

Windows 10.
it runs smooth (copy fromk log):

Code:

2020.11.06:13:23:19.563: main GPU1: 66C 41% 105W
GPU1: cclock 1267 MHz, cvddc 756 mV, mclock 1750 MHz, mvddc 850 mV, Tj 72C, Tmem 94C
2020.11.06:13:23:41.618: main Eth speed: 50.552 MH/s, shares: 3/0/0, time: 0:01

But what im worried is: Tmem 94C ??
We can fry en egg at 94c...

[UnclWish]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

[Pe_Da]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

Looks similar here, since estimated 6 hours almost all shares on ETC-Mining (Ethermine) are invalid.
ETH seems to be working properly, still ...

Doublecheck with NBMiner, no issues! Seems to be a problem with Phoenix only .... oh wait, NBMiner produce many (>20%) rejected shares at ETC-Mining currently ... 

[UnclWish]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

Looks similar here, since estimated 6 hours almost all shares on ETC-Mining (Ethermine) are invalid.
ETH seems to be working properly, still ...

Doublecheck with NBMiner, no issues! Seems to be a problem with Phoenix only .... oh wait, NBMiner produce many (>20%) rejected shares at ETC-Mining currently ... 

I'm use lolMiner now. All fine.

[fanis77]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

Same problem...incorrect shares on epoch 385

[abrgeza]

Need help guys,

My MSI Radeon RX 5700 XT Gaming with this setting 5.1c:

Code:

-acm -clKernel 1 -clNew 1 -clf 0 ^
-gt 126 -cclock 1300 -cvddc 750 -mclock 900 ^

Windows 10.
it runs smooth (copy fromk log):

Code:

2020.11.06:13:23:19.563: main GPU1: 66C 41% 105W
GPU1: cclock 1267 MHz, cvddc 756 mV, mclock 1750 MHz, mvddc 850 mV, Tj 72C, Tmem 94C
2020.11.06:13:23:41.618: main Eth speed: 50.552 MH/s, shares: 3/0/0, time: 0:01

But what im worried is: Tmem 94C ??
We can fry en egg at 94c...

94C is fine, you should be worried if it reach 104C.

[Globalminingcorp]

I am new to the this forum and was hoping to find some help with my miner.  I have trouble keeping it online, sometimes it runs for an hour sometimes a day, with the longest ever being 1 week.  When the Phoenix Miner 5.1c does crash sometimes the command prompt window is just closed and other times the computer has rebooted.  Here is my setup.

HP desktop AMD A10, 4GB RAM (have another 4GB ordered), 600W PSU, Windows 10 64-bit.
2x - RX5700 GPU
Radeon driver 20.10.1

I have tried different settings for the cards themselves but nothing has seemed to make a difference, including what I found in previous posts on here, 1350MHz Core, 1750MHz Mem, 780mv.  Thanks for any suggestions anyone has.

Can you post the last 20-25 lines of your logfile after this happens? Maybe we can find some clues there

[AzzAz]

Need help guys,

My MSI Radeon RX 5700 XT Gaming with this setting 5.1c:

Code:

-acm -clKernel 1 -clNew 1 -clf 0 ^
-gt 126 -cclock 1300 -cvddc 750 -mclock 900 ^

Windows 10.
it runs smooth (copy fromk log):

Code:

2020.11.06:13:23:19.563: main GPU1: 66C 41% 105W
GPU1: cclock 1267 MHz, cvddc 756 mV, mclock 1750 MHz, mvddc 850 mV, Tj 72C, Tmem 94C
2020.11.06:13:23:41.618: main Eth speed: 50.552 MH/s, shares: 3/0/0, time: 0:01

But what im worried is: Tmem 94C ??
We can fry en egg at 94c...

94C is fine, you should be worried if it reach 104C.

did you try mvddc under 900? 860 i.e. ? and -tt etc ?

[UnclWish]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

Looks similar here, since estimated 6 hours almost all shares on ETC-Mining (Ethermine) are invalid.
ETH seems to be working properly, still ...

Doublecheck with NBMiner, no issues! Seems to be a problem with Phoenix only .... oh wait, NBMiner produce many (>20%) rejected shares at ETC-Mining currently ... 

I'm use lolMiner now. All fine.

I had to switch to SRBminer and TeamredMiner (ETC). My 4 Vega 64 rig is mining ok now. PM give me only invalid shares.
However, on my second rig ,with just one Vega 64, PM is still mining just fine even after reboot. It creates DAG properly.

lolMiner for AMD gives more speed and pool aside speed, IMHO. Just try it.

[Pe_Da]

For my RX 580 8Gb rigs Phoenix 5.1c didn't create DAG epoch №385. It creates DAG for 0,5 sec and all shares are incorrect. Speed shows normal.

I think PM just didn't support epochs 385+

Looks similar here, since estimated 6 hours almost all shares on ETC-Mining (Ethermine) are invalid.
ETH seems to be working properly, still ...

Doublecheck with NBMiner, no issues! Seems to be a problem with Phoenix only .... oh wait, NBMiner produce many (>20%) rejected shares at ETC-Mining currently ...  

I'm use lolMiner now. All fine.

Problem solved by using other miner. Teamredminer or lolminer works fine for me if I run the nVidia and AMD Cards in parallel instances.
It seems PhoenixMiner have a problem on Radeon since Epoch 385. NBMiner as well!

My Rig:

16GB RAM

1x Radeon VII (16GB)                    >TeamRedMiner
2x Radeon RX 5700 (8GB)              >TeamRedMiner
1x Radeon RX 5700XT (8GB)          >TeamRedMiner
1x Geforce GTX 1660 Super (6GB)  >PhoenixMiner
1x Geforce RTX 2060 Super (8GB)  >PhoenixMiner

[rozsada]

Hi guys!
Need help for dual mining.

rig with rx 480 8G

I am mining ETH
Is it possible to mine extra coin? (SIA, DCR or other coin)
If so, can you help with a command line?

Thanks.

[miner29]

Hi guys!
Need help for dual mining.

rig with rx 480 8G

I am mining ETH
Is it possible to mine extra coin? (SIA, DCR or other coin)
If so, can you help with a command line?

Thanks.

These days it costs more in ETH earnings to dual mine then it is to just straight mine ETH.
All my rigs are on straight ETH.

[Wolfie]

Hey man -

Would you be so kind as to look into adding support for ProgPow-Epic ,

$EPIC = Epic Cash, 3 algo MW coin, 21mill supply, great little project

With all the 4GB cards available, we need some decent work for them.

Here is their GitLab link :

https://gitlab.com/epiccash

SRBminer already supports them RandomX\CPU,

TTminer already support them on ProgPOW\nVidia

thx in advance for anything you can do Wink

[rozsada]

Hi guys!
Need help for dual mining.

rig with rx 480 8G

I am mining ETH
Is it possible to mine extra coin? (SIA, DCR or other coin)
If so, can you help with a command line?

Thanks.

These days it costs more in ETH earnings to dual mine then it is to just straight mine ETH.
All my rigs are on straight ETH.

Thanks for the reply.
Anyway - could you provide a command line for dual mining?

[abrgeza]

Need help guys,

My MSI Radeon RX 5700 XT Gaming with this setting 5.1c:

Code:

-acm -clKernel 1 -clNew 1 -clf 0 ^
-gt 126 -cclock 1300 -cvddc 750 -mclock 900 ^

Windows 10.
it runs smooth (copy fromk log):

Code:

2020.11.06:13:23:19.563: main GPU1: 66C 41% 105W
GPU1: cclock 1267 MHz, cvddc 756 mV, mclock 1750 MHz, mvddc 850 mV, Tj 72C, Tmem 94C
2020.11.06:13:23:41.618: main Eth speed: 50.552 MH/s, shares: 3/0/0, time: 0:01

But what im worried is: Tmem 94C ??
We can fry en egg at 94c...

94C is fine, you should be worried if it reach 104C.

did you try mvddc under 900? 860 i.e. ? and -tt etc ?

No, I modded bios (cclock 1366, mclock 1800 with moded strap, cvddc 800, mvddc 850), 55.5MH/s.
Tj 58-66C, Tmem 82-92C (it depends of room temps).