soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 03:48:41 PM |
|
Or if one adds 12vdc fans to the exhaust of the box, powering with 12v out of the 4 pin molex, even unplugging everything then reassembling, plugging in the external 12vdc fans FIRST would kill any high voltage on that 12 volt rail. This might not be much help if the power supply has multiple 12 volt rails in which case you'd have to make sure each rail had a fan on before getting attached to the miner.
or just pick up a $3 PSU tester with a screen instead of jumping the pins and let it drain the rails Yes, but lets get this exploding capacitor problem ended so they can start shipping again. Does the board have MOVs on the 12v rail? Not sure how effective at protecting tantalum given the tantalum sensitivity to high voltage and there's the power loss in the MOVs given that you'd want them conducting before the tantalum(s) fry and the closer the MOVs knee to the rail voltage the higher the leakage. Would that be significant overall? Probably not. They'd need add the MOV to the board. If it's multi-layver they can't just drill a pair of holes willy-nilly but careful placement of holes drilled, copper surface of rails exposed with scraping, MOV soldered to 12v and ground is a lot of work. Perhaps a connector, internal, with the MOV installed; unplug power ribbon, insert connector, plug power ribbon(s) into added connector might satisfy insurance people and protect the board. An exploded capacitor isn't a fire tho it may give off gas that smells like smoke. And if you use any of my suggestions and your miner doesn't get an exploded cap, you can send tips to: 18XUsmKnuPmGdNaPrtpwSr11iAXFUdFUys
|
|
|
|
loktang1125
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 03:55:51 PM |
|
could anybody tell me which one is #1 and #3
HW status:
ASIC slot #1: 73.0 ℃ ASIC slot #2: - ASIC slot #3: 73.0 ℃ ASIC slot #4: - ASIC slot #5: 64.0 ℃ ASIC slot #6: 68.0 ℃
|
|
|
|
Paladin69
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 03:56:11 PM |
|
A Jupiter in this Config will use app. 890W. Well that fucking sucks. Thanks for being cheap knc. I was so happy when I heard people were getting under 600w. I was hopeful that these 1300w PSU's from BFL could power two of them. Looks like not anymore.
|
|
|
|
-Redacted-
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:01:10 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
|
|
|
|
greek_hephaestus
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 162
Merit: 100
Eloncoin.org - Mars, here we come!
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:03:59 PM |
|
Order #12x Miner Saturn Date of Order 3/6/2013 Paid 9/7/2013 Location Athens/Greece Status change In progress a few hours a go According to KnCMiner, they work full time all weekend to catch 15th of October!!! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif)
|
|
|
|
Paladin69
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:04:11 PM |
|
That is the only correct way to shut a system down - pull the jumper, then power off the PSU. Thanks for the info!
|
|
|
|
Gyrsur
Legendary
Offline
Activity: 2856
Merit: 1520
Bitcoin Legal Tender Countries: 2 of 206
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:04:21 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
+1
|
|
|
|
bobsag3
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:06:45 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
+1 +2 None of this "its the HX850's fault". That model might just be particularly susceptible to this problem... But I have used over 30 HX850s for mining-related functions without a single issue till KnC.
|
|
|
|
loktang1125
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:07:04 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
in this case, the jumper is the paperclip?
|
|
|
|
aspeer
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 102
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:09:20 PM |
|
W. T. F.?
This is running 0.93...umm help!?
thats odd, my exact process: arrived with .91 only did 190 gh/s on jupiter >> updated to .94 ssh in and do reboot. waited 15 minutes for it to come back online, major issues >> updated to .92 ssh in and reboot waited again, miner wont run at all now >> ran reboot patch, rebooted still wont run >> updated back to 93 rebooted miner runs and gets near 480 GH/s now
|
|
|
|
aspeer
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 102
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:10:48 PM |
|
could anybody tell me which one is #1 and #3
HW status:
ASIC slot #1: 73.0 ℃ ASIC slot #2: - ASIC slot #3: 73.0 ℃ ASIC slot #4: - ASIC slot #5: 64.0 ℃ ASIC slot #6: 68.0 ℃
looking at the back beagle board closest too you it runs from left to right for the ribbon cable connections. (jp7 - jp12 usually) asic slot one being jp7
|
|
|
|
soy
Legendary
Offline
Activity: 1428
Merit: 1013
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:12:33 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
+1 I, for one, would like to see that shown experimentally. I personally believe there is no fault in pulling the plug.
|
|
|
|
DPoS
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:17:24 PM |
|
Not sure but FractionalReserve posted this on KNC Forums www.kncminer.comhopefully this fix is the real deal Asic Bords with 4 VRMs - bug - cool properly until FW fix arrives! Today, 04:07 PM The new asic bords with only 4 VRMs are using to much power. KNC will release a bug fix for this in next (0.95?) Firmware hopefully arriving in short (Today?) A Jupiter in this Config will use app. 890W. So it can be difficult to start with a 850W ATX. (You can still run them with only 3 boards conected) The VRMs are also running over spec with app. 50+ A current each! They probably won't burn, but if you can cool them extra until the new firmware is realeased, do it!! The Asics are tunning to hot (+70 deg C) as they get app, 0.9V instead of 0.7V as they are supposed to. Cool them as much as you can!!! The Problem is due to the VRMs not working according to spec but KNC will be able to fix it with new firmware (we did our own patch for our miners yesterday). Easiest fix to cool properly is to provide cool air, belo 20 deg C is a good idea. Open case + big fan will also work. PS, this does not apply to 8 VRM asic boards. No worries here. again found this on knc forums hope if helps Searing I pointed this out yesterday and it kinda got dissed by the KNC collective you don't fix something that isn't broke unless you know everything that can break it
|
|
|
|
MrHempstock
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 140
Merit: 100
"Don't worry. My career died after Batman, too."
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:18:03 PM |
|
I'm not sure why people are freaking out, I get responses within 24 hours every time when I make a reasonable, non answered in the FAQ and fully formed request of them. See below:
You apply logic to the situation? MADNESS!
|
BTCitcointalk 1%ers manipulate the currency and deceive its user community.
|
|
|
MrHempstock
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 140
Merit: 100
"Don't worry. My career died after Batman, too."
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:18:50 PM |
|
I think we all need to step back for a second and chill out on the KNC folks. We have to remember that this is a collaboration between Orsoc and KNC, and both companies have reputations on the line. If I were to speculate (and that's all we can do without any information coming from KNC) then as soon as units started having problems, the Orsoc guys put the breaks on the project. To be honest, I can't even blame them. You can't be a long term success in this industry if your products burn houses down. I'm guessing that: 1) KNC and Orsoc are madly working on the issues and will have them fixed as soon as humanly possible. 1) KNC isn't allowed to say anything about the problems due to the agreement between them and Orsoc. Nobody wants a unit shipped to their home that is going to achieve 1/10 to 1/4th of the expected hash rate. Nor would I imagine they want one that catches on fire. I'm not involved and have not special information, but I know KNC will make this right. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FiJDcizv.jpg&t=665&c=U_tpw9cI-N7sxw) + a lot effing more than 1
|
BTCitcointalk 1%ers manipulate the currency and deceive its user community.
|
|
|
DeathAndTaxes
Donator
Legendary
Offline
Activity: 1218
Merit: 1079
Gerald Davis
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:19:29 PM |
|
There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result... Yeah I have turned PC off GPU rigs at the switch a couple thousand times. It is a non-issue. There is a reason open frame GPU miners used power supplies with a physical power switch on back. The theory that it powering off highly regulated UL listed ATX power supply destroyed connected equipment doesn't hold water. There are ~300 million PC in the US. If yanking the power would blow up a motherboard 1% of the time and the average PC experiences 3 blackouts a year then you would be talking something on the order of 9 million destroyed PC every single year. Say average PC is $500. We are talking about a half a billion dollars. If it genuinely was a problem then PC mother boards (and GPU and other hardware) would come with circuit breakers or at least a $0.20 quick burn fuse. Of course they don't ... because it isn't a problem.
|
|
|
|
cypherdoc
Legendary
Offline
Activity: 1764
Merit: 1002
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:20:18 PM |
|
|
|
|
|
MrHempstock
Full Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif) ![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 140
Merit: 100
"Don't worry. My career died after Batman, too."
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:20:33 PM |
|
And now, "Gay Life On Bitcoin", a venture by 2 loveable users, Cypherdoc and Avenger. Let's all donate BTC and send these two on a honeymoon. Anything to get them out of here.
|
BTCitcointalk 1%ers manipulate the currency and deceive its user community.
|
|
|
faetos
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:22:24 PM |
|
Order #12x Miner Saturn Date of Order 3/6/2013 Paid 9/7/2013 Location Athens/Greece Status change In progress a few hours a go According to KnCMiner, they work full time all weekend to catch 15th of October!!! ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) i see Saturns moving forward but Junipers are not goig anywhere. what happed to the sacred queue? So so disappoint
|
|
|
|
joeventura
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
October 11, 2013, 04:23:06 PM |
|
And here is a tip for everyone. You know those two pins you jump to make the PSU work? Do you know what those are used for?
When you press the OFF switch your motherboard opens those two pins, telling the PSU to power everything down safely. That is the only correct way to shut a system down - pull the jumper, then power off the PSU.
If you just flip the PSU switch off, you leave a "whole lot of amerage" suddenly looking for the quickest way to get home. And electrons aren't fussy, if they can find a shorter path across a component instead of thru it, they'll use that. If there are unseen micro droplets of solder on the solder mask that present a shorter path, they'll use that path, carbonizing the solder mask and making it an even BETTER shortcut - resulting in nasty smelling smoke and burned solder mask...
Just flipping the PSU switch to off might not break anything the first time or even 100th time you do it, but eventually you'll pay the price, and the magic smoke gets out. There's a very valid reason why you don't just turn off your computer by yanking the plug out of the wall socket - and flipping the PSU switch is the equivalent of doing that. Do that to your desktop computer a few times and see how well it runs as a result...
Good tip thanks!
|
|
|
|
|