Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[tdguchi]

Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w

if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?

I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC

Could anyone help me with that?

Also.. which pool is the best for 1 GPU?

Thanks

[1714878629]

1714878629

[1714878629]

1714878629

[1714878629]

1714878629

[IncludeBeer]

Dear Claymore
Please, pay attention on dramatically decrease hash rate with epoch growth.
I test it on my rig with 3 RX580 4Gb (use -benchmark key) and here are results:
epoch #120 ETH: GPU0 29.380 Mh/s, GPU1 29.532 Mh/s, GPU2 29.944 Mh/s
epoch #130 ETH: GPU0 29.146 Mh/s, GPU1 29.273 Mh/s, GPU2 29.700 Mh/s
epoch #140 ETH: GPU0 27.567 Mh/s, GPU1 27.664 Mh/s, GPU2 27.992 Mh/s
epoch #160 ETH: GPU0 21.309 Mh/s, GPU1 21.397 Mh/s, GPU2 21.666 Mh/s
epoch #180 ETH: GPU0 18.493 Mh/s, GPU1 18.509 Mh/s, GPU2 18.795 Mh/s

So very shortly we got decrease hash rate on 5% (between epoch #130 and #140).
Please fix this bug or explain what to do.

That isn't a bug. As epoch goes up, hashrate of many amd gpu's goes down. It is known. 

[matthewusa2000]

Hi team,
New to mining so apologize for the noob quesition. If I'm mining with Claymore at ~42Mh/s, and I have 550 total shares, when does the account get setup? GPU GTX 1080
Account# 0xea515a90ee5598b38cc9eb3de23d03e3006aa921

Claymore settings:
epools
# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.

 POOL: eth-eu.dwarfpool.com:8008, WALLET: 0xea515a90ee5598b38cc9eb3de23d03e3006aa921/YourWorker, PSW: x, ESM: 0, ALLPOOLS: 0
 POOL: us1.ethermine.org:4444, WALLET: 0xea515a90ee5598b38cc9eb3de23d03e3006aa921.YourWorker, PSW: x, ESM: 1, ALLPOOLS: 0
# POOL: coinotron.com:3344, WALLET: YourUserName.YourWorkerName, PSW: YourWorkerPass, WORKER: , ESM: 2, ALLPOOLS: 1
# POOL: us-east1.ethereum.miningpoolhub.com:20535, WALLET: YourLogin.YourWorkerName, PSW: YourWorkerPass, WORKER: YourLogin.YourWorkerName, ESM: 2

Config

# WARNING! Remove "#" characters to enable lines, with "#" they are disabled and will be ignored by miner! Check README for details.
# WARNING! Miner loads options from this file only if there are not any options in the command line!

-epool http://us1.ethpool.org:3333
-ewal 0xea515a90ee5598b38cc9eb3de23d03e3006aa921
-epsw x
#-dpool stratum+tcp://yiimp.ccminer.org:4252
#-dwal DsUt9QagrYLvSkJHXCvhfiZHKafVtzd7Sq4
#-dpsw x
-esm 1
-mode 1
-tt 70
#-asm 0

[bkbirge]

Hey all, been mining eth for a little bit with this now and just decided to try dual mining w/dcr as a next step. I am getting a few Mh/s drop in eth mining when going dual as compared with running single, is this normal? The claim on the front page is no hit to eth mining in dual mode so wondering if I'm doing something wrong. Thanks for any help!

I'm running all nvidia, a mix of 1060,1070,1080 on different miners, each miner exhibits the same behavior.

Here's my batch file to start it all up...
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool us1.ethermine.org:14444 -ewal myinfo4ethwallet -epsw x -dpool dcr.suprnova.cc:3252 -dwal myinfo4dcr -dpsw x -dcoin dcr -allpools 1

[rorschach1]

Anyone  

hey new to all this...

i'm using a GTX980 to mine eth and lbry; however, i'm only getting 2.9 Mh/s on each

I saw:

9xx cards in Windows 10 x64: you have to use old drivers (for example, 352.xx)

how do i get the old drivers installed? Nvidia website only goes to 372.54

I have 384 installed, i'm assuming this is why i have such low hash-rates

You must update your win10 to creators update!
https://support.microsoft.com/en-us/instantanswers/d4efb316-79f0-1aa1-9ef3-dcada78f3fa0/get-the-windows-10-creators-update

I use Win 7 64 bit on one my pc and drivers are 372.70 v. And my Asus nvidia 1060 3 Gb give 24 Mh eth average

[scryptr]

Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w

if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?

I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC

Could anyone help me with that?

Also.. which pool is the best for 1 GPU?

Thanks

NOT ENOUGH POWER--

You need a 1000W PSU for 5 to 6 GPUS.  A PSU needs to have more capacity than  the maximum power draw for ALL of your GPUs combined.  The highest efficiency is at about 60-70 percent of the rated capacity of the PSU.

You can not get by without overloading and burning out a low-power, low efficiency PSU.  5 x 150W equals 750W, and that is greater than 650W (your PSU).  A low-wattage algorithm may work for a while, but the PSU will still burn out.  It could also explode or catch fire.

I no longer buy cheap, unrated PSUs.  Stick with Gold, or Platinum, from a reliable manufacturer with a soiid warranty.  A PSU will really explode if over-worked.       --scryptr

[papampi]

Hi guys
I have gone crazy to setup 6 GPU, 5 works ok with no problem
When I enable the 6th one after 10-15 minutes   cpu usage goes high and reach 90%. no program with high cpu in task manager but "system"
tried with MSI afterburner running to speed up fans, and without it  
If I leave it like that after a while claymore gives error. or system freeze before WatchDog could restart.

Code:

NVML: Cannot get current Temp, Err 999
NVML: Cannot get current Fan Speed, Err 999

All 6 GPU are detected and working fine, tried to run with 5 and cycle the 6th one to check if problem is from risers or power cables ( Disabled pcie1 , run with 5, disabled pcie2 run with 5 .... )
All ok with 5 GPU no matter which one, as soon as I enable 6th the cpu goes high.
system is :
Windows 10, 1703 , all drivers updated to latest with "Driver Booster"
Mobo: MSI Z170A XPower Gaming Titanium Edition
PSU: Thermaltake Toughpower XT Gold 1275W
GPU: 6x 1070 Asus Dual 8OG
Ram: ADATA XPG Z1 DDR4 8GB 2800MHz CL17 Dual Channel
CPU: Pentium G4400 3.3GHz LGA 1151 Skylake CPU
HDD: SAMSUNG 750 EVO 120GB SATAIII Solid State Drive


PEG0, PEG1, PEG2 gen 1 (tried with auto too)
4G enabled
IGD disabled (tried with enable too)

[CarlOrff]

Hey guys,

what hashrates are you getting on nvidia cards?
Single/dual mining (preferably with ETH+SIA)

1070 =?
1080 =?
1080Ti =?

Thanks a lot!

Hey,

GTX 1070 ETH+SC @ 100 Watts
Ubuntu 16.04 + Claymore 9.7
 ETH : ~26 MH/s
 SC : ~260 MH/s
Average since more 3 days.

The 9.7 version is a very good one, thanks again Claymore.

Your welcome

[CarlOrff]

I'm running all nvidia, a mix of 1060,1070,1080 on different miners, each miner exhibits the same behavior.

Here's my batch file to start it all up...
setx GPU_FORCE_64BIT_PTR 0
setx GPU_MAX_HEAP_SIZE 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_SINGLE_ALLOC_PERCENT 100

You can erase this section : it is only for AMD GPUs.

[aedboy]

Please help me
My rig 12 gpu galax gtx 1050ti*8 and msi rx560*4
PSU corsair vs650*2
MB biostar tb250 btc pro
Ram 8gb

I'm install gpu 8+4
It freeze  
but install 1050ti*8 and rx560*3 not freeze
How to solve?  

http://www.mx7.com/i/003/ZSDWRj.JPG

May be your PSU are not strong enough.
what about   1050ti*7 and rx560*4?

7*4 freeze
rx560*4 freeze
rx560*3 not freeze

I'm try PSU 650+650+750w Unsolvable

[Bulletdodger]

Hey guys,

what hashrates are you getting on nvidia cards?
Single/dual mining (preferably with ETH+SIA)

1070 =?
1080 =?
1080Ti =?

Thanks a lot!

Hey,

GTX 1070 ETH+SC @ 100 Watts
Ubuntu 16.04 + Claymore 9.7
 ETH : ~26 MH/s
 SC : ~260 MH/s
Average since more 3 days.

The 9.7 version is a very good one, thanks again Claymore.

Your welcome

Thanks a bunch,
these are decent stats even though Sia is kinda low (you get 1500 sols when solo mining it), but ok, pretty decent.
Any info on 1080Ti?

I'm thinking about switching my nvidia cards from ZEC to Dual miner...

[p33k]

I have all the cards you listed and whattomine.com is fairly accurate on hashrates.

Hey guys,

what hashrates are you getting on nvidia cards?
Single/dual mining (preferably with ETH+SIA)

1070 =?
1080 =?
1080Ti =?

Thanks a lot!

Hey,

GTX 1070 ETH+SC @ 100 Watts
Ubuntu 16.04 + Claymore 9.7
 ETH : ~26 MH/s
 SC : ~260 MH/s
Average since more 3 days.

The 9.7 version is a very good one, thanks again Claymore.

Your welcome

Thanks a bunch,
these are decent stats even though Sia is kinda low (you get 1500 sols when solo mining it), but ok, pretty decent.
Any info on 1080Ti?

I'm thinking about switching my nvidia cards from ZEC to Dual miner...

[Bulletdodger]

Yeah, I did check it out.

Just wanted to see is there a difference "in real life".

I tried mining with my 1080tis, but no success. I'm using latest win 10, latest drivers, clay 9.7 etc,
but keep getting this shit, so I gave up for now (scouted the internet with no clear solution as well).

[papampi]

Any helps on this please ...

Hi guys
I have gone crazy to setup 6 GPU, 5 works ok with no problem
When I enable the 6th one after 10-15 minutes   cpu usage goes high and reach 90%. no program with high cpu in task manager but "system"
tried with MSI afterburner running to speed up fans, and without it  
If I leave it like that after a while claymore gives error. or system freeze before WatchDog could restart.

Code:

NVML: Cannot get current Temp, Err 999
NVML: Cannot get current Fan Speed, Err 999

All 6 GPU are detected and working fine, tried to run with 5 and cycle the 6th one to check if problem is from risers or power cables ( Disabled pcie1 , run with 5, disabled pcie2 run with 5 .... )
All ok with 5 GPU no matter which one, as soon as I enable 6th the cpu goes high.
system is :
Windows 10, 1703 , all drivers updated to latest with "Driver Booster"
Mobo: MSI Z170A XPower Gaming Titanium Edition
PSU: Thermaltake Toughpower XT Gold 1275W
GPU: 6x 1070 Asus Dual 8OG
Ram: ADATA XPG Z1 DDR4 8GB 2800MHz CL17 Dual Channel
CPU: Pentium G4400 3.3GHz LGA 1151 Skylake CPU
HDD: SAMSUNG 750 EVO 120GB SATAIII Solid State Drive


PEG0, PEG1, PEG2 gen 1 (tried with auto too)
4G enabled
IGD disabled (tried with enable too)

[gh05t77]

Dear Claymore
Please, pay attention on dramatically decrease hash rate with epoch growth.
I test it on my rig with 3 RX580 4Gb (use -benchmark key) and here are results:
epoch #120 ETH: GPU0 29.380 Mh/s, GPU1 29.532 Mh/s, GPU2 29.944 Mh/s
epoch #130 ETH: GPU0 29.146 Mh/s, GPU1 29.273 Mh/s, GPU2 29.700 Mh/s
epoch #140 ETH: GPU0 27.567 Mh/s, GPU1 27.664 Mh/s, GPU2 27.992 Mh/s
epoch #160 ETH: GPU0 21.309 Mh/s, GPU1 21.397 Mh/s, GPU2 21.666 Mh/s
epoch #180 ETH: GPU0 18.493 Mh/s, GPU1 18.509 Mh/s, GPU2 18.795 Mh/s

So very shortly we got decrease hash rate on 5% (between epoch #130 and #140).
Please fix this bug or explain what to do.

That isn't a bug. As epoch goes up, hashrate of many amd gpu's goes down. It is known. 

I run benchmark on RX480 8Gb and got the same results. So it's not depend of memory size.
Does this problem have NVIDIA cards too?

[duffann]

I am currently using 378.92 with windows 7 64 bit. Claymore suggests 368.61 for this config. Do you think it will differ much and should i downgrade to that version ?

[Gunna01]

So my system is crashing when creating the dag when running 6 GPU, 5 has been solid all week. Thought it was a riser but put a new one in with the same result.

Any suggestions?

[papampi]

So my system is crashing when creating the dag when running 6 GPU, 5 has been solid all week. Thought it was a riser but put a new one in with the same result.

Any suggestions?

Have you tried -lidag  option ?

Code:

-lidag   low intensity mode for DAG generation, it can help with OC or weak PSU. Supported values are 0, 1, 2, 3, more value means lower intensity. Example: "-lidag 1".
   You can also specify values for every card, for example "-lidag 1,0,3". Default value is "0" (no low intensity for DAG generation).

Also try -gser

Code:

-gser   this setting can improve stability on multi-GPU systems if miner hangs during startup. It serializes GPUs initalization routines. Use "-gser 1" to serailize some of routines and "-gser 2" to serialize all routines.
   Default value is "0" (no serialization, fast initialization).

[tdguchi]

Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w

if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?

I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC

Could anyone help me with that?

Also.. which pool is the best for 1 GPU?

Thanks

NOT ENOUGH POWER--

You need a 1000W PSU for 5 to 6 GPUS.  A PSU needs to have more capacity than  the maximum power draw for ALL of your GPUs combined.  The highest efficiency is at about 60-70 percent of the rated capacity of the PSU.

You can not get by without overloading and burning out a low-power, low efficiency PSU.  5 x 150W equals 750W, and that is greater than 650W (your PSU).  A low-wattage algorithm may work for a while, but the PSU will still burn out.  It could also explode or catch fire.

I no longer buy cheap, unrated PSUs.  Stick with Gold, or Platinum, from a reliable manufacturer with a soiid warranty.  A PSU will really explode if over-worked.       --scryptr

yeah, 1000w for  5 o 6 gpu, but I only have one, that should be enough...or not?

[Gunna01]

So my system is crashing when creating the dag when running 6 GPU, 5 has been solid all week. Thought it was a riser but put a new one in with the same result.

Any suggestions?

Have you tried -lidag  option ?

Code:

-lidag   low intensity mode for DAG generation, it can help with OC or weak PSU. Supported values are 0, 1, 2, 3, more value means lower intensity. Example: "-lidag 1".
   You can also specify values for every card, for example "-lidag 1,0,3". Default value is "0" (no low intensity for DAG generation).

Also try -gser

Code:

-gser   this setting can improve stability on multi-GPU systems if miner hangs during startup. It serializes GPUs initalization routines. Use "-gser 1" to serailize some of routines and "-gser 2" to serialize all routines.
   Default value is "0" (no serialization, fast initialization).

Cheers, managed to get it working. I had to increase virtual memory to over 17500 however since adding the 6th card all 3 of this card type have dropped from 25mh to 16mh. My Aorus are still running at 28 but the msi, all running same bios are running at 16. Take 6th card out and hash umps up to 25 on the remaining 2 MSI.....

edit: For some reason MSIAfterburner had underclocked the cards when 6 were plugged in. All good now