scryptr
Legendary
 Offline
Activity: 1793
Merit: 1028
|
 |
July 17, 2017, 11:39:43 AM
Last edit: July 17, 2017, 01:41:11 PM by scryptr |
|
Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w
if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?
I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC
Could anyone help me with that?
Also.. which pool is the best for 1 GPU?
Thanks
NOT ENOUGH POWER-- You need a 1000W PSU for 5 to 6 GPUS. A PSU needs to have more capacity than the maximum power draw for ALL of your GPUs combined. The highest efficiency is at about 60-70 percent of the rated capacity of the PSU. You can not get by without overloading and burning out a low-power, low efficiency PSU. 5 x 150W equals 750W, and that is greater than 650W (your PSU). A low-wattage algorithm may work for a while, but the PSU will still burn out. It could also explode or catch fire. I no longer buy cheap, unrated PSUs. Stick with Gold, or Platinum, from a reliable manufacturer with a soiid warranty. A PSU will really explode if over-worked. --scryptr yeah, 1000w for 5 o 6 gpu, but I only have one, that should be enough...or not? YOU SHOULD BE GOOD-- In your case, I would begin checking for another hardware problem. Overheating, or a poor connection somewhere. It still could be the PSU, if your PC has a bargain PSU. --scryptr |
|
|
|
|
|
|
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
parentibule
|
|
July 17, 2017, 01:05:11 PM |
|
Hi,
For a 1060, what driver is better to install on a Debian? Packages from contrib/non-free or drivers from nvidia?
|
|
|
|
|
scryptr
Legendary
Offline
Activity: 1793
Merit: 1028
|
|
July 17, 2017, 01:43:08 PM |
|
Hi,
For a 1060, what driver is better to install on a Debian? Packages from contrib/non-free or drivers from nvidia?
FOR BEST PERFORMANCE, NVIDIA-- I have never mined crypto with anything else. --scryptr |
|
|
|
|
parentibule
|
|
July 17, 2017, 02:58:53 PM |
|
Hi,
For a 1060, what driver is better to install on a Debian? Packages from contrib/non-free or drivers from nvidia?
FOR BEST PERFORMANCE, NVIDIA-- I have never mined crypto with anything else. --scryptr Ok, I started with contrib, it's version 375.66-1. I have 18.9MH/s + 315MH/s DCR without OC (I don't find how to OC on Debian 9  ) |
|
|
|
|
|
bkbirge
|
|
July 17, 2017, 03:02:32 PM |
|
Need help here. My 1070 is doing 31mh/s on windows 7 but sadly windows 7 only detects 5 of my gpu. I then try windows 10 pro. With the latest driver it's able to recognised 7 gpu out of 8 but the hashrate is only 2mh/s each. The gpu on the m.2 is not being detected as well.. help..
You need creator's update for win10, do a google. |
|
|
|
|
|
bkbirge
|
|
July 17, 2017, 03:17:22 PM |
|
Need help here. My 1070 is doing 31mh/s on windows 7 but sadly windows 7 only detects 5 of my gpu. I then try windows 10 pro. With the latest driver it's able to recognised 7 gpu out of 8 but the hashrate is only 2mh/s each. The gpu on the m.2 is not being detected as well.. help..
You need creator's update for win10, do a google. Ok thanks for your reply. So the current nvidia driver is fine yeah? Works for me, I'm using whatever the latest drivers are. |
|
|
|
|
seventux
Newbie
Offline
Activity: 79
Merit: 0
|
|
July 17, 2017, 03:24:11 PM |
|
Need help here. My 1070 is doing 31mh/s on windows 7 but sadly windows 7 only detects 5 of my gpu. I then try windows 10 pro. With the latest driver it's able to recognised 7 gpu out of 8 but the hashrate is only 2mh/s each. The gpu on the m.2 is not being detected as well.. help..
Are you using Windows 10 64 bit version 1607 above? |
|
|
|
|
tdguchi
Newbie
Offline
Activity: 4
Merit: 0
|
|
July 17, 2017, 04:59:08 PM |
|
Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w
if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?
I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC
Could anyone help me with that?
Also.. which pool is the best for 1 GPU?
Thanks
NOT ENOUGH POWER-- You need a 1000W PSU for 5 to 6 GPUS. A PSU needs to have more capacity than the maximum power draw for ALL of your GPUs combined. The highest efficiency is at about 60-70 percent of the rated capacity of the PSU. You can not get by without overloading and burning out a low-power, low efficiency PSU. 5 x 150W equals 750W, and that is greater than 650W (your PSU). A low-wattage algorithm may work for a while, but the PSU will still burn out. It could also explode or catch fire. I no longer buy cheap, unrated PSUs. Stick with Gold, or Platinum, from a reliable manufacturer with a soiid warranty. A PSU will really explode if over-worked. --scryptr yeah, 1000w for 5 o 6 gpu, but I only have one, that should be enough...or not? YOU SHOULD BE GOOD-- In your case, I would begin checking for another hardware problem. Overheating, or a poor connection somewhere. It still could be the PSU, if your PC has a bargain PSU. --scryptr This is my psu (bougth 6 or 7 years ago with the cpu and motherboard (the newest component is the gpu) could you evaluate it please? |
|
|
|
|
|
Saphire
|
|
July 17, 2017, 05:29:01 PM |
|
These are my Nvidia and AMD ETH only and ETH+SIA Rigs. Nvidia ETH Only  Nvidia ETH+SIA AMD ETH Only AMD ETH+SIA What is wrong with AMD GPU at Dual Mining ? My Dual Mining Settings: EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal MyAdress -epsw x -dcoin sia -dpool stratum+tcp://sia-eu1.nanopool.org:7777 -dwal MyAdress -dpsw x -ftime 10 |
|
|
|
|
gh05t77
Newbie
Offline
Activity: 6
Merit: 0
|
|
July 17, 2017, 05:33:24 PM |
|
What is wrong with AMD GPU at Dual Mining ?
My Dual Mining Settings:
EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal MyAdress -epsw x -dcoin sia -dpool stratum+tcp://sia-eu1.nanopool.org:7777 -dwal MyAdress -dpsw x -ftime 10
Try to play with -dcri key. Set it about -dcri 10 and press + / - in miner window to find the best value |
|
|
|
|
vuli
Full Member
Offline
Activity: 233
Merit: 100
Andrius | Junior Business developer at Unboxed ICO
|
|
July 17, 2017, 05:35:10 PM |
|
damn dude, where did you got so much money to buy all this cards?
Yeah, I noticed if I mine ETH+SIA, eth drops a lot, like in you case, so I rather went to ETH+DCR.
Try to lower -dcri with -(minus) button on you keyboard, or + to raise.
|
Unboxed - rowing community of people getting paid to do what they love to get a share of the $36 billion brands are spending annually on Facebook Ads
|
|
|
|
HowlingMad
|
 |
July 17, 2017, 06:05:00 PM |
|
Windows 10 - miner crashes.
I am using AMD 15.300 drivers, Clay 9.7, put the environment variables in, tried running it in compatability mode as Windows 8.
Cannot figure out what the problem is.
Also, how do I upload the screenshot?
|
Windows 10, R280x * 3
|
|
|
biggee
Member
Offline
Activity: 73
Merit: 10
|
|
July 17, 2017, 06:15:56 PM
Last edit: July 17, 2017, 06:46:51 PM by biggee |
|
Not submitting any shares on DCR with 9.7 MUSIC/DCR dual.
MUSIC is submitting fine but DCR, although receiving lots of jobs never submits a share.
Was fine on 9.5.
*UPDATE*
9.7 crashes on all three of my AMD (crim 16.9.2) / WIN 10 rigs.
Rolling back to 9.5, this release is useless for me.
Also, don't know if it's just me, but this release runs a few of my GPU cards much hotter than 9.5 with no improvement in hash rate. Temp on 3 cards (across 2 of the rigs) was hitting 75+, 71 is the max any of my cards reach usually - most of them are around the 68 mark.
|
|
|
|
|
mikkowendell
Newbie
Offline
Activity: 41
Merit: 0
|
|
July 17, 2017, 07:09:44 PM |
|
Not submitting any shares on DCR with 9.7 MUSIC/DCR dual.
MUSIC is submitting fine but DCR, although receiving lots of jobs never submits a share.
Was fine on 9.5.
*UPDATE*
9.7 crashes on all three of my AMD (crim 16.9.2) / WIN 10 rigs.
Rolling back to 9.5, this release is useless for me.
Also, don't know if it's just me, but this release runs a few of my GPU cards much hotter than 9.5 with no improvement in hash rate. Temp on 3 cards (across 2 of the rigs) was hitting 75+, 71 is the max any of my cards reach usually - most of them are around the 68 mark.
SAME HERE, IT ALSO CRASHES WITH MY RX 480S RIG WIN10, AT FIRST I THOUGHT IT WQAS MY PCIE RISERS HAVING AN ISSUE WITH SO I CHANGED, THEN IT RAN GREAT FOR TWO DAYS, THEN IT KEEPS ON CRASHING AGAIN AND AGAIN. ON MY R9 390 AND 290 IT WORKS FINE. ROLLING BACK AT 9.5 AND IT WORKS WELL EXCEPT FOR THE TEMP AND FAN LIST WHICH IS SO CONFUSING BECAUSE IT IS NOT IN ORDER SO I HAVE TO FIND THE RIGHT PLACE FOR EACH CARD ACCORDINGLY. FURTHERMORE, I GUESS ITS IN THE MINER ISSUE, BECAUSE EVERY AFTER I RESTART MY RIG DUE TO CRASH PROBLEM, IT SHOWS THAT THE RADEON SETTING HAS BEEN SET TO DEFAULT. I DONT HAVE THIS KIND OF MESSAGE BEFORE, I BELIEVE ITS ON THE MINER WHICH IS DOING THE UNDERCLOCKING/OVERCLOCKING OR WHATSOEVER(I REALLY DONT KNOW). ALL CARDS ARE ON DEFAULT SETTING, I DONT DO OVER/UNDERCLOCKING AT ALL. I HOPE CLAYMORE WOULD FIX THIS. THANKS A LOT! |
|
|
|
|
|
Saphire
|
|
July 17, 2017, 07:56:04 PM |
|
What is wrong with AMD GPU at Dual Mining ?
My Dual Mining Settings:
EthDcrMiner64.exe -epool eth-eu1.nanopool.org:9999 -ewal MyAdress -epsw x -dcoin sia -dpool stratum+tcp://sia-eu1.nanopool.org:7777 -dwal MyAdress -dpsw x -ftime 10
Try to play with -dcri key. Set it about -dcri 10 and press + / - in miner window to find the best value Thank you, i think it is ok now.  |
|
|
|
|
justin86
Full Member
Offline
Activity: 406
Merit: 100
Market Integration Platform
|
|
July 17, 2017, 08:33:34 PM |
|
I can not run it I thought my computer is very old  |
|
|
|
scryptr
Legendary
Offline
Activity: 1793
Merit: 1028
|
|
July 17, 2017, 09:54:48 PM |
|
Hi, i have a rx 580 Nitro+ 4Gb gpu, with a power supply of 650w
if I only use ethereum mode, all its fine (24mh/s) but, when I try dual mining, after a short time, my pc reboots, could it be caused by lack of current or voltage?
I run the miner only with required parameters, epool dpool wallets, and passwords, my rx 580 is NOT modded and running at 60-64ºC
Could anyone help me with that?
Also.. which pool is the best for 1 GPU?
Thanks
NOT ENOUGH POWER-- You need a 1000W PSU for 5 to 6 GPUS. A PSU needs to have more capacity than the maximum power draw for ALL of your GPUs combined. The highest efficiency is at about 60-70 percent of the rated capacity of the PSU. You can not get by without overloading and burning out a low-power, low efficiency PSU. 5 x 150W equals 750W, and that is greater than 650W (your PSU). A low-wattage algorithm may work for a while, but the PSU will still burn out. It could also explode or catch fire. I no longer buy cheap, unrated PSUs. Stick with Gold, or Platinum, from a reliable manufacturer with a soiid warranty. A PSU will really explode if over-worked. --scryptr yeah, 1000w for 5 o 6 gpu, but I only have one, that should be enough...or not? YOU SHOULD BE GOOD-- In your case, I would begin checking for another hardware problem. Overheating, or a poor connection somewhere. It still could be the PSU, if your PC has a bargain PSU. --scryptr This is my psu (bougth 6 or 7 years ago with the cpu and motherboard (the newest component is the gpu) could you evaluate it please? IT SEEMS GENERIC-- The specifications are not in English. Most USA PSU manufacturers use an efficiency rating scale involving colors: White, Bronze, Silver, Gold, Platinum, Titanium, with Titanium being tops. Not all manufacturers use all of the colors for their models. An "80+ Gold" PSU is considered good. The PSU you linked for me did not have a rating. I have some older PSUs that really just have a wattage number tacked on, but can barely produce 1/2 the load that is claimed on the label. The other thing is the warranty. The best warranty service in the USA, for my money,is EVGA . I just bought 2 EVGA 80+ Platinum PSUs that have 10-year warranties. EVGA backs up their warranty with service. Your PSU is likely fine for 1 GPU, especially an RX 580. For some reason (it was very late when I answered your post), I thought you had a multi-card rig. If you do build a multi-card rig, don't try to save money with a cheap PSU. the better-rated PSU will use less electricity and last longer. That means the GPUs will pay for the PSU more quickly, even if it is an expensive model. --scryptr |
|
|
|
GG87
Newbie
Offline
Activity: 29
Merit: 0
|
|
July 17, 2017, 10:48:10 PM |
|
Is it normal to have only 16% gpu usage on HwInfo ?  i'm getting about 230 Mh/s @ 1000watt ( 4 rx480 + 4 rx 580 ) |
|
|
|
|
|
Vann
|
|
July 17, 2017, 10:58:00 PM |
|
Is it normal to have only 16% gpu usage on HwInfo ? i'm getting about 230 Mh/s @ 1000watt ( 4 rx480 + 4 rx 580 ) That's pretty good. Ethash is a memory hard algorithm, so the memory utilization is what's important. You can check the memory controller load in GPU-Z. It should be at 100%. |
|
|
|
|
GG87
Newbie
Offline
Activity: 29
Merit: 0
|
|
July 17, 2017, 11:29:22 PM |
|
Is it normal to have only 16% gpu usage on HwInfo ? i'm getting about 230 Mh/s @ 1000watt ( 4 rx480 + 4 rx 580 ) That's pretty good. Ethash is a memory hard algorithm, so the memory utilization is what's important. You can check the memory controller load in GPU-Z. It should be at 100%. thanks  |
|
|
|
|
|
