Avalon ASIC users thread

[-ck]

problem solved 10x it works with no problem now   
on what address do I send donation ?
Regards
Thor

You're welcome, either the address in my forum signature or the one from the cgminer readme. Thanks for donating

[1714890271]

1714890271

[1714890271]

1714890271

[1714890271]

1714890271

[1714890271]

1714890271

[1714890271]

1714890271

[thorvald]

problem solved 10x it works with no problem now   
on what address do I send donation ?
Regards
Thor

You're welcome, either the address in my forum signature or the one from the cgminer readme. Thanks for donating

10x

1btc sent

[-ck]

While I'm at it, a word about the overclocking, based on what I've seen so far...

I'd suggest enabling --avalon-auto with a range of frequencies with --avalon-freq even if you're not overclocking, to allow cgminer to clock it down should you have an issue with heat.

For example, if you just want to run it at 300, add these to More Options:
--avalon-auto --avalon-freq 256-300

If you do want to overclock:
For batch 1 owners with the original PSU, I wouldn't suggest going over 325 or you'll risk your PSU failing:
--avalon-auto --avalon-freq 256-325

For batch 2 owners, there were a number of different PSUs, but even they can run into trouble so I'd suggest 345 as the upper limit to prevent instability:
--avalon-auto --avalon-freq 256-345

If you have upgraded your PSU to a good one >= 850W, then you can probably run --avalon-auto without a frequency range, and it may tune you up to around 365.

[bitdaniel]

fyi:
This is my Batch 2 Avalon with the factory PSU of 750w and 4 modules chip-frequenze with about 360!


Running stable since 12 hours.

[loshia]

fyi:
This is my Batch 2 Avalon with the factory PSU of 750w and 4 modules chip-frequenze with about 360!


Running stable since 12 hours.

Dude,

PSU will die in a second. Do not do that and change PSU immediately

[fhh]

Dude,

PSU will die in a second. Do not do that and change PSU immediately

I also think that this is no good idea for the life of the PSU.
With this settings it has to deliver around 820-850 Wat I think... 

[elasticband]

fyi:
This is my Batch 2 Avalon with the factory PSU of 750w and 4 modules chip-frequenze with about 360!


Running stable since 12 hours.

running stable for 12hours? but it only says under 2hrs in the picture...... I doubt you will last long on that PSU with those settings

[elasticband]

also 2000+ HW errors in 1hr and 20mins seems quite high...... would love to know your diffi1 shares.....

[bitdaniel]

Believe me, it runs now since this morning.

[elasticband]

1.7% HW error rate?

still your stats only says 3hrs, has it restarted several times?

temps seem low enough

[elasticband]

big difference between slush saying 90,000 in last 0 rounds(which is estimated) and your hardware saying 110,000

90,000 on 360mhz with 4 modules is not good speed anyway....... I run 80+ with 3

[Tinua]

Dude,

PSU will die in a second. Do not do that and change PSU immediately

I also think that this is no good idea for the life of the PSU.
With this settings it has to deliver around 820-850 Wat I think...  

It takes 940 Watt from the wall!

[bitdaniel]

big difference between slush saying 90,000 in last 0 rounds(which is estimated) and your hardware saying 110,000

90,000 on 360mhz with 4 modules is not good speed anyway....... I run 80+ with 3

Its 90,000 in the last 10 rounds... (-;
You see actualy 111,000 ^^

[AM4Bitcoin]

Just buy a sufficient PSU, there are not that expensive. You will have better results.

[cypherdoc]

1.7% HW error rate?

still your stats only says 3hrs, has it restarted several times?

temps seem low enough

according to con, those levels of fan rate are high.  what an ideal rate?  btw, what units are those figures?

[elasticband]

fans are almost at max..... but tempratures look low wnough

[cypherdoc]

guys i need help with what to plug into what with my new SeaSonic Platinum-1000 1000W ATX12V / EPS12V 80 PLUS PLATINUM.  this will have to be externalized b/c of the larger size of the unit.

how many cords plug into the avalon's PCB?  and then where do i plug the other ends of the cords into the Seasonic?

[cypherdoc]

fans are almost at max..... but tempratures look low wnough

what's the max, 4000?

[bitdaniel]

fans are almost at max..... but tempratures look low wnough

I put the fans to max by option -avalon-fan.

[bitdaniel]

fans are almost at max..... but tempratures look low wnough

what's the max, 4000?

Max is what you can see on my screenshot.