LarryFossil
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:05:42 PM |
|
Thread I started Since I Just signed up and couldn't post in this thread =P (Thanks btc forum) https://bitcointalk.org/index.php?topic=296628.msg3182123#msg3182123Hello all, I have recently received 2 version2+ blades that require 120watts @ 10amps / blade. (Already overclocked and set at 12V) I have attached some images to explain the PSU. I have tried numerous hardware configurations to get the blade working, but every time I plug in the ASIC the PSU / Fans / etc... turn off. I tried using https://bitcointalk.org/index.php?topic=205369.0 & talking on a variety IRC channels. Is my PSU not capable of supplying the needed voltage / wattage / amps to the specified ASIC board? If so, what am I doing wrong? Here are the specs: http://www.amazon.com/Thermaltake-PurePower-W0118RU-ATX12V-Supply/dp/B000P9VGMWPRODUCT FEATURES: Complies with Intel ATX12V 1.3 specs;Supports the modern Intel and AMD CPUs;115/230v full-range adjustment;Durable and efficient 80mm fan;Industrial grade protections: SCP, OPP, OCP, OTP, UVP;High-efficiency, clean voltage rails. Power Device Type Power supply Power Device / Form Factor Internal Voltage Provided +3.3, +/-5, +/-12 V Voltage Required AC 115 - 230 V Power Provided (W) 350 Watt Circuit Protection Circuit breaker Input Connector(s) 1 Output Connector(s) 2 x 15 pin Serial ATA power, 1 x power 20 pin ATX, 1 x power 4 pin ATX12V connector, 7 x 4 pin internal power, 2 x 4 pin mini-power connector Pictures:VoltMeter: https://www.dropbox.com/s/pvii0nyr6k4dhel/2013-09-18%2011.10.53.jpgPSU: https://www.dropbox.com/s/9ymyq88joxuv38o/2013-09-18%2011.08.39.jpg1 Example Wiring Setup: https://www.dropbox.com/s/dtwh6zn59qhsfxb/2013-09-18%2011.08.23.jpg2 Example Molex Setup: https://www.dropbox.com/s/ahehts2np8nx5lq/2013-09-18%2012.08.39.jpgAnother Molex Picture for Example 2: https://www.dropbox.com/s/fubh0dg509bkbcl/2013-09-18%2012.08.49.jpgAnother Molex Picture for Example 2: https://www.dropbox.com/s/eb45l84ryee92vg/2013-09-18%2012.09.07.jpg(I can supply more pictures if needed) Note: I also followed the guide I shared in beginning of post. I tried using the molex splitter and other 12v outputs.
Much help is appreciated. Thanks in advance. Larry =)
Ps. If I could get some help with this subject, I will create a better tutorial than Dogie did. I just need to get everything working first.Update 2: I switched around the polarity & now everything seems to have power, but I still have no blinking lights for IP (ASIC device) activity. It is plugged into slot 3 & slot 1 is connected to the computer through a LAN line. I have added some pictures to give you a good idea where I am at with getting this blade to work. Thanks! Trial & Error: Reset the ASIC device by touching the two pins closets to left of Ethernet port. Resetting the entire PSU Made sure my ip ranges are in range for .254 on router Currently showing ~10.5-11V with two 120mm fans connected. Currently displaying ~11-11.6V with 0 fans connected. Tested various points on the ASIC board to see if it has voltage. (Which it does) Just no blinking lights or IP activity More Pictures: Network Connection thru PC: (Attached Devices): https://www.dropbox.com/s/lwxq7wk4465xagb/2013-09-18%2014.32.32.jpgNetwork Router Cable / Ports: https://www.dropbox.com/s/mfn4r7eukz7jk4b/2013-09-18%2014.31.02.jpgNetwork Router Lights: https://www.dropbox.com/s/phddvac6q6ekk5v/2013-09-18%2014.32.02.jpgNetwork Port / Pwr: https://www.dropbox.com/s/l6dxzuluue8smqs/2013-09-18%2014.25.03.jpg (No lights blinking) 10amp Fuse: https://www.dropbox.com/s/vh3tya5ttbtefem/2013-09-18%2014.25.41.jpg10amp Fuse / Multimeter: https://www.dropbox.com/s/o4cg7vt6be49fcp/2013-09-18%2014.26.18.jpg(Can take more pictures if need be) wrong polarity here https://www.dropbox.com/s/o4cg7vt6be49fcp/2013-09-18%2014.26.18.jpgred is + black is - I initially tried the polarity the other way and that didn't work. The PSU kept shutting off. I am also getting voltages across the fuse ~ 10.8V - 11V with two 120mm Fans connected. When the fans are not connected the voltmeter displays ~11.5V. Either way, the device is connecting and no IP activity displays.
|
|
|
|
Rishodi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:17:33 PM |
|
My new-gen blades periodically restart all at once. There are 10 of them connected to a backplane and powered by one of the plug-in PSU models. The uptime never seems to go higher than a couple of hours, so that's approximately how long they're going before restarting. It happens to all of them at the same time. What might the issue be?
|
Bitrated user: Rishodi.
|
|
|
dogie (OP)
Legendary
Offline
Activity: 1666
Merit: 1185
dogiecoin.com
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:29:11 PM |
|
My new-gen blades periodically restart all at once. There are 10 of them connected to a backplane and powered by one of the plug-in PSU models. The uptime never seems to go higher than a couple of hours, so that's approximately how long they're going before restarting. It happens to all of them at the same time. What might the issue be?
Could be power interruption or both pools appearing down, ie internet problems.
|
|
|
|
rob143
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 138
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:44:07 PM |
|
Is there a source for the new fuses? I have the second gen blade and just would like to buy a few more just in case.
|
|
|
|
mdopro1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:46:27 PM |
|
I just received 3 of Gen2 blades, two work fine but the third one seems to be connected but not hashing at all. It may also be restarting, right now it's 1m 57s running. Voltages on both terminal are showing exactly 12.04V and power is coming from two separate rails of molex with a splitter to support 10AMP - so 2 yellow and 3 black in each connector respectively.
I can access the config page and all chips show OOO. This means that I have an IP, no conflict and I can connect to the hasher. Hash rate sitting at 0 all the time so far.
I copied/pasted stratum proxy and pool user info from a working blade so that shouldn't be a problem either.
Any suggestions?
EDIT: - I have two proxies running on two separate machines which connect to two different pools and neither one are working. - PSU is a 850W Corsair Professional series, voltages are ok and 2 other miners are working off the same PSU.
|
New Bitcoin fund doubling platform has launched! Receive Automated Payment Every 2 Hours Appealing alternative with Sophisticated algorithms. https://Btc-Funds.com
|
|
|
Swimmer63
Legendary
Offline
Activity: 1593
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:49:57 PM |
|
not enough subnet mask to go from 192.168.x.x to 10.x.x.x ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Do you have a separate switch? You can manually change your PC's IP address to be 192.168.1.x just so you can connect to blade and change it's config Yes, thx and just got pc to show 192.168.0.1 as gateway, however, I never got docs with new blade and do not know the blade IP plus if it is 192.168.1.x I am still off some with 192.168.0.x. Also, good idea to change the blade and then can go back to 10.0.0.1 if needs be. thx ip should be 192.168.1.254 as long as your router gives that range. 1-254 I am trying to connect a blade to my office network and I think I have a similar issue to above. The Default Gateway is 192.168.0.1. The router goes to 254. But I can't access the config page using 192.168.1.254:8000 or 192.168.0.254:8000. Tried from both a wireless and direct connection on a networked PC. The blade is plugged right into the router and it's flashing green. Any suggestions?
|
|
|
|
xyzzy099
Legendary
Offline
Activity: 1065
Merit: 1077
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 08:55:13 PM |
|
not enough subnet mask to go from 192.168.x.x to 10.x.x.x ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Do you have a separate switch? You can manually change your PC's IP address to be 192.168.1.x just so you can connect to blade and change it's config Yes, thx and just got pc to show 192.168.0.1 as gateway, however, I never got docs with new blade and do not know the blade IP plus if it is 192.168.1.x I am still off some with 192.168.0.x. Also, good idea to change the blade and then can go back to 10.0.0.1 if needs be. thx ip should be 192.168.1.254 as long as your router gives that range. 1-254 I am trying to connect a blade to my office network and I think I have a similar issue to above. The Default Gateway is 192.168.0.1. The router goes to 254. But I can't access the config page using 192.168.1.254:8000 or 192.168.0.254:8000. Tried from both a wireless and direct connection on a networked PC. The blade is plugged right into the router and it's flashing green. Any suggestions? You need to be on a network with 192.168.1.x. Can you temporarily change your router's IP address to 192.168.1.1 instead of 192.168.0.1? You will be able to connect if you do that. EDIT: You will need to change your PC's IP address to 192.168.1.(whatever) also. If you want to stay on the 192.168.0.x net, you can change the blade to 192.168.0.x, and then set your other IPs back to normal.
|
Libertarians: Diligently plotting to take over the world and leave you alone.
|
|
|
Rishodi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 09:36:29 PM |
|
My new-gen blades periodically restart all at once. There are 10 of them connected to a backplane and powered by one of the plug-in PSU models. The uptime never seems to go higher than a couple of hours, so that's approximately how long they're going before restarting. It happens to all of them at the same time. What might the issue be?
Could be power interruption or both pools appearing down, ie internet problems. I have a server PC right next to the blades, running off the same power strip, running a stratum proxy which the blades all use. The server hasn't been restarting, so it's not the power blinking, at least not at the wall. If the proxy restarts could that cause the blades to reset?
|
Bitrated user: Rishodi.
|
|
|
mdopro1
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 10:11:28 PM |
|
My new-gen blades periodically restart all at once. There are 10 of them connected to a backplane and powered by one of the plug-in PSU models. The uptime never seems to go higher than a couple of hours, so that's approximately how long they're going before restarting. It happens to all of them at the same time. What might the issue be?
Could be power interruption or both pools appearing down, ie internet problems. I have a server PC right next to the blades, running off the same power strip, running a stratum proxy which the blades all use. The server hasn't been restarting, so it's not the power blinking, at least not at the wall. If the proxy restarts could that cause the blades to reset? Try this, run all blades and have them hashing. While they are running, restart the proxy that they connect to. Simply CTRL+C and immediately restart the proxy. I have 4 blades and they kept restarting every 20 minutes until I did this and now they run for as long as they can... I'm new to it all, so far my record was 7 days running. But be quick so your blades don't connect to backup server.
|
New Bitcoin fund doubling platform has launched! Receive Automated Payment Every 2 Hours Appealing alternative with Sophisticated algorithms. https://Btc-Funds.com
|
|
|
Swimmer63
Legendary
Offline
Activity: 1593
Merit: 1004
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 10:15:07 PM |
|
not enough subnet mask to go from 192.168.x.x to 10.x.x.x ![Smiley](https://bitcointalk.org/Smileys/default/smiley.gif) Do you have a separate switch? You can manually change your PC's IP address to be 192.168.1.x just so you can connect to blade and change it's config Yes, thx and just got pc to show 192.168.0.1 as gateway, however, I never got docs with new blade and do not know the blade IP plus if it is 192.168.1.x I am still off some with 192.168.0.x. Also, good idea to change the blade and then can go back to 10.0.0.1 if needs be. thx ip should be 192.168.1.254 as long as your router gives that range. 1-254 I am trying to connect a blade to my office network and I think I have a similar issue to above. The Default Gateway is 192.168.0.1. The router goes to 254. But I can't access the config page using 192.168.1.254:8000 or 192.168.0.254:8000. Tried from both a wireless and direct connection on a networked PC. The blade is plugged right into the router and it's flashing green. Any suggestions? You need to be on a network with 192.168.1.x. Can you temporarily change your router's IP address to 192.168.1.1 instead of 192.168.0.1? You will be able to connect if you do that. EDIT: You will need to change your PC's IP address to 192.168.1.(whatever) also. If you want to stay on the 192.168.0.x net, you can change the blade to 192.168.0.x, and then set your other IPs back to normal. OK -thanks for the info. That will be challenging.
|
|
|
|
LarryFossil
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 10:25:56 PM |
|
Thread I started Since I Just signed up and couldn't post in this thread =P (Thanks btc forum) https://bitcointalk.org/index.php?topic=296628.msg3182123#msg3182123Hello all, I have recently received 2 version2+ blades that require 120watts @ 10amps / blade. (Already overclocked and set at 12V) I have attached some images to explain the PSU. I have tried numerous hardware configurations to get the blade working, but every time I plug in the ASIC the PSU / Fans / etc... turn off. I tried using https://bitcointalk.org/index.php?topic=205369.0 & talking on a variety IRC channels. Is my PSU not capable of supplying the needed voltage / wattage / amps to the specified ASIC board? If so, what am I doing wrong? Here are the specs: http://www.amazon.com/Thermaltake-PurePower-W0118RU-ATX12V-Supply/dp/B000P9VGMWPRODUCT FEATURES: Complies with Intel ATX12V 1.3 specs;Supports the modern Intel and AMD CPUs;115/230v full-range adjustment;Durable and efficient 80mm fan;Industrial grade protections: SCP, OPP, OCP, OTP, UVP;High-efficiency, clean voltage rails. Power Device Type Power supply Power Device / Form Factor Internal Voltage Provided +3.3, +/-5, +/-12 V Voltage Required AC 115 - 230 V Power Provided (W) 350 Watt Circuit Protection Circuit breaker Input Connector(s) 1 Output Connector(s) 2 x 15 pin Serial ATA power, 1 x power 20 pin ATX, 1 x power 4 pin ATX12V connector, 7 x 4 pin internal power, 2 x 4 pin mini-power connector Pictures:VoltMeter: https://www.dropbox.com/s/pvii0nyr6k4dhel/2013-09-18%2011.10.53.jpgPSU: https://www.dropbox.com/s/9ymyq88joxuv38o/2013-09-18%2011.08.39.jpg1 Example Wiring Setup: https://www.dropbox.com/s/dtwh6zn59qhsfxb/2013-09-18%2011.08.23.jpg2 Example Molex Setup: https://www.dropbox.com/s/ahehts2np8nx5lq/2013-09-18%2012.08.39.jpgAnother Molex Picture for Example 2: https://www.dropbox.com/s/fubh0dg509bkbcl/2013-09-18%2012.08.49.jpgAnother Molex Picture for Example 2: https://www.dropbox.com/s/eb45l84ryee92vg/2013-09-18%2012.09.07.jpg(I can supply more pictures if needed) Note: I also followed the guide I shared in beginning of post. I tried using the molex splitter and other 12v outputs.
Much help is appreciated. Thanks in advance. Larry =)
Ps. If I could get some help with this subject, I will create a better tutorial than Dogie did. I just need to get everything working first.Update 2: I switched around the polarity & now everything seems to have power, but I still have no blinking lights for IP (ASIC device) activity. It is plugged into slot 3 & slot 1 is connected to the computer through a LAN line. I have added some pictures to give you a good idea where I am at with getting this blade to work. Thanks! Trial & Error: Reset the ASIC device by touching the two pins closets to left of Ethernet port. Resetting the entire PSU Made sure my ip ranges are in range for .254 on router Currently showing ~10.5-11V with two 120mm fans connected. Currently displaying ~11-11.6V with 0 fans connected. Tested various points on the ASIC board to see if it has voltage. (Which it does) Just no blinking lights or IP activity More Pictures: Network Connection thru PC: (Attached Devices): https://www.dropbox.com/s/lwxq7wk4465xagb/2013-09-18%2014.32.32.jpgNetwork Router Cable / Ports: https://www.dropbox.com/s/mfn4r7eukz7jk4b/2013-09-18%2014.31.02.jpgNetwork Router Lights: https://www.dropbox.com/s/phddvac6q6ekk5v/2013-09-18%2014.32.02.jpgNetwork Port / Pwr: https://www.dropbox.com/s/l6dxzuluue8smqs/2013-09-18%2014.25.03.jpg (No lights blinking) 10amp Fuse: https://www.dropbox.com/s/vh3tya5ttbtefem/2013-09-18%2014.25.41.jpg10amp Fuse / Multimeter: https://www.dropbox.com/s/o4cg7vt6be49fcp/2013-09-18%2014.26.18.jpg(Can take more pictures if need be) wrong polarity here https://www.dropbox.com/s/o4cg7vt6be49fcp/2013-09-18%2014.26.18.jpgred is + black is - I initially tried the polarity the other way and that didn't work. The PSU kept shutting off. I am also getting voltages across the fuse ~ 10.8V - 11V with two 120mm Fans connected. When the fans are not connected the voltmeter displays ~11.5V. Either way, the device is connecting and no IP activity displays. Update 3: I switched around my + & - and put them in series with the ASIC chip. I turn on PSU; Fan starts up then quits & the PSU shuts off. What could be my problem? I am using a 12V rail that is meant for 12A and I only need 1.2Watts / 10Amps per blade. Problem: Led light behind the ethernet port starts blinking when I initially power the board, but it shuts off. PSU works when not connected to ASIC board. PSU Specs: https://www.dropbox.com/s/9ymyq88joxuv38o/2013-09-18%2011.08.39.jpgPossibilities: Bad PSU Pulling to many amps from ASIC board PSU not supplying advertised voltage Other: Fuse is working (tested em with diode checker) Fans come on when not plugged into ASIC (using other 12V Rail to power the fans) Only reading about 11.5-11.3V on multimeter when no fans are plugged in. No smoking of the equipment as of yet =P
|
|
|
|
gaboo08
Newbie
Offline
Activity: 14
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 11:03:04 PM |
|
Anyone else having similar issues with the new blade version where it won't hash when using the same IP address for the stratum proxy? And when using two separate proxies, it seems to switch between the two? My hash rate is still ranging from 2000 to 3800 at the moment and I can't figure out how to get it to work.
|
|
|
|
notlist3d
Legendary
Offline
Activity: 1456
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 18, 2013, 11:13:43 PM |
|
Anyone else having similar issues with the new blade version where it won't hash when using the same IP address for the stratum proxy? And when using two separate proxies, it seems to switch between the two? My hash rate is still ranging from 2000 to 3800 at the moment and I can't figure out how to get it to work.
Try slush pool from the first page. Dogie did a kick ass job on guide. I was getting the same 2-3kish then downloaded file from first page, ran it and mining at slush at great speeds.
|
|
|
|
jml
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 12:12:58 AM |
|
The parameters are updated or the system is simply restarted! 517 That's what I get when I update and restart my blades. What are you expecting to see? I don't believe it auto-refreshes back to original url or anything. After the update, I would expect values to be updated from the last POST sent from browser. The user would then have to redirect (not hit the back key) to the home page of the blade which would be http://192.168.x.x:8000. For some reason unknown, the update function does not work from my laptop and had to use the browser on my phone to make the update work! I will try and update to see what was the exact cause for chrome and IE9 not to update the settings on the blade.
|
"Everything is a matter of degree"
|
|
|
RicRock
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 12:37:22 AM |
|
After the update, I would expect values to be updated from the last POST sent from browser. The user would then have to redirect (not hit the back key) to the home page of the blade which would be http://192.168.x.x:8000. A POST would only work that way if you weren't restarting the httpd server which is what you are doing when restarting the blade after the config. Much like when you update the configuration of a router or whatever from a web interface
|
|
|
|
Stack
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 12:54:37 AM |
|
Update 3: I switched around my + & - and put them in series with the ASIC chip. I turn on PSU; Fan starts up then quits & the PSU shuts off. What could be my problem? I am using a 12V rail that is meant for 12A and I only need 1.2Watts / 10Amps per blade. Problem: Led light behind the ethernet port starts blinking when I initially power the board, but it shuts off. PSU works when not connected to ASIC board. PSU Specs: https://www.dropbox.com/s/9ymyq88joxuv38o/2013-09-18%2011.08.39.jpgPossibilities: Bad PSU Pulling to many amps from ASIC board PSU not supplying advertised voltage Other: Fuse is working (tested em with diode checker) Fans come on when not plugged into ASIC (using other 12V Rail to power the fans) Only reading about 11.5-11.3V on multimeter when no fans are plugged in. No smoking of the equipment as of yet =P That doesn't sound right. Don't they need 120Watts per blade? as per OP
|
|
|
|
jml
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 01:32:13 AM |
|
After the update, I would expect values to be updated from the last POST sent from browser. The user would then have to redirect (not hit the back key) to the home page of the blade which would be http://192.168.x.x:8000. A POST would only work that way if you weren't restarting the httpd server which is what you are doing when restarting the blade after the config. Much like when you update the configuration of a router or whatever from a web interface I am assuming it uses POST as I don't see arguments on the address which would be GET.
|
"Everything is a matter of degree"
|
|
|
xstr8guy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 01:43:59 AM |
|
I just received 3 of Gen2 blades, two work fine but the third one seems to be connected but not hashing at all. It may also be restarting, right now it's 1m 57s running. Voltages on both terminal are showing exactly 12.04V and power is coming from two separate rails of molex with a splitter to support 10AMP - so 2 yellow and 3 black in each connector respectively.
I can access the config page and all chips show OOO. This means that I have an IP, no conflict and I can connect to the hasher. Hash rate sitting at 0 all the time so far.
I copied/pasted stratum proxy and pool user info from a working blade so that shouldn't be a problem either.
Any suggestions?
EDIT: - I have two proxies running on two separate machines which connect to two different pools and neither one are working. - PSU is a 850W Corsair Professional series, voltages are ok and 2 other miners are working off the same PSU.
Try a hardware reset. I had a similar issue and that fixed it. Btw, got the bad Blade working by doing a hardware reset by shorting the two pins as shown in this illustration... ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fx6gG2OS.jpg&t=665&c=D8Cr5Z7ChUUBdA)
|
|
|
|
RicRock
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 01:54:14 AM |
|
After the update, I would expect values to be updated from the last POST sent from browser. The user would then have to redirect (not hit the back key) to the home page of the blade which would be http://192.168.x.x:8000. A POST would only work that way if you weren't restarting the httpd server which is what you are doing when restarting the blade after the config. Much like when you update the configuration of a router or whatever from a web interface I am assuming it uses POST as I don't see arguments on the address which would be GET. I totally understand what your saying... it restarts the webserver so there is no way it can post "back" to the config screen once your "session" is broken by a restart.
|
|
|
|
LarryFossil
Newbie
Offline
Activity: 28
Merit: 0
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
September 19, 2013, 02:56:26 AM |
|
Update 3: I switched around my + & - and put them in series with the ASIC chip. I turn on PSU; Fan starts up then quits & the PSU shuts off. What could be my problem? I am using a 12V rail that is meant for 12A and I only need 1.2Watts / 10Amps per blade. Problem: Led light behind the ethernet port starts blinking when I initially power the board, but it shuts off. PSU works when not connected to ASIC board. PSU Specs: https://www.dropbox.com/s/9ymyq88joxuv38o/2013-09-18%2011.08.39.jpgPossibilities: Bad PSU Pulling to many amps from ASIC board PSU not supplying advertised voltage Other: Fuse is working (tested em with diode checker) Fans come on when not plugged into ASIC (using other 12V Rail to power the fans) Only reading about 11.5-11.3V on multimeter when no fans are plugged in. No smoking of the equipment as of yet =P That doesn't sound right. Don't they need 120Watts per blade? as per OP Yea, Your right. That is a typo. Its suppose to be 1.2Volts @10 amps / 120 Watts, but thanks for the help.. Update 4: I found out my PSU problem with the help of Wizkid on IRC. He gave me the idea to connect my two 5v extra wires to a 5-6v fan. (Older PSU's won't work properly unless power is distributed.) I joined both 5v wires from the modified molex splitter (per OP) & used one ground wire from same rail to power the 6v fan. Plugged it in and boom everything worked. Including the two 120mm fans I have on another rail. Seen IP connectivity and Connected to the ASIC through the browser at ease =P Now, I need to figure out how to input the settings perfectly =P to mine on slush's pool. Hopefully that is a bit simpler... I have been fiddling with this stuff since yesterday. Should of been much simpler, but I paid 50 bucks for a cheapo pwr supply and ended up wasting valuable time cause of a different power distributing configuration.
|
|
|
|
|