Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[sxemini]

@mehrdadb3

Use srbpolaris 3.4 and the pimp straps and you get more hashrate. It´s the easiest way.
All of my elpidas reach 30,5 - 32 mh.

[kokocik554455]

мoжeт ктo п пoмoч?  дoбывaю кaлиcтo и тaм дaг фaйл 17. клeймop вpyбaeт кoммиcию и нaчинaeт гpyзить 196 дaгфaйл   . пoкa гpyзит кoммиcия выключaeтьcя. пoтoтoм oпять гpyзитьcя 17 дa гфaйл.  вpeмя тepяeтьcя нa этo вce 40-50 ceк.  кaк cдeлaть чтoб клeймop мaйнил тyжe мoнeтy чтo и я?

[sandgo]

Are there any good news for 1060 6GB 9gbps? Currently , hashrate still lower than 23... 

[kokocik554455]

who can help? I get Calixto and there Dag file 17. the kleymor cuts a kommisiya and begins to load 196 дaгфaйл. while the kommisiya loads it is switched off. pototy to be loaded 17 yes гфaйл again. time is lost on all this 40-50 sec. how to make that the kleymor maynit a touch a coin as I?

[boo50]

a lot of AMD miners ask for new equihash 144_5 miner, there are demand and it's growing, already 4 coins forked to new algo - BTCZ, LTZ, SAFE, XSG and only Nvidia can mine ATM.

[mehrdadb3]

@mehrdadb3

Use srbpolaris 3.4 and the pimp straps and you get more hashrate. It´s the easiest way.
All of my elpidas reach 30,5 - 32 mh.

can u put your straps use for your card if u have msi rx570 gaming x 4gb and my memory is elpida/hynix

[MikeGR7]

Stale shares are shares for a block submitted after the next block is already being mined. Its result from network latency and fast block times and has nothing to do with memory errors or overclocking. Too much overclocking can definetlly cause memory errors and invalid/rejected shares though. Some of my Powercolor 4GB Red Dragon RX 570's run stable at 29.5-30.5 MH/s with a 1150 MHz core and 2075 MHz memory clock. I do have some that will only run at 1950-1975 MHz memory overclock at ~28.5 MH/s.

Aghh, yes man thanks for the correction Invalid is the correct term i tried to refer to.

[MikeGR7]

Don't expect much more from it.

I have several 570's ranging from 26,5 to 28,5Mhs.

I haven't seen more then 28.5 in any 570 to date, so yours is totaly normal performance wise.

really? even my old 470 refs are doing better then the numbers you state.

rx570 can go up to 31. Normally however it hashes around 29.5-30.5
I've got a rig of rx570 4gb MSI gaming with Elpida doing mere 29.4. And the only slower 570 I've got is ASUS Expedition hashing at 28.8

Of course it's possible if you are willing to deal with memory errors in HWinfo.
GPUs can have hundreds of errors and seem to work fine but you have a steady higher stale shares percentage and the ocasional rejected share so i cannot accept 30mh as a 570s normal number.

https://s33.postimg.cc/hgv9pnzxb/dh31.jpg


Thank you very much for your post friend!

I seriously have no idea why i get such awful performance from my 570s... Most of them use combined memory chips from Elpida and Micron... I used one click timing patch and i cannot get more then 28,5 stable no way.
I have 7 of them from Asus and Gigabyte, all same shit, even have one that maxes at 1880MHZ mem.

What straps are you using? Maybe that's the deal.
also fyi mem errors in HwInfo are both those that were corrected and those that were not.

[haliy-2017]

sandgo
How did you reach 23, ...

[uDwcHYO]

haliy-2017
i think he has samsung memory on cards

[carlo_0000]

hello my  2G card have problem with dag on musicoin
i thought we could mine still a year till 2019

[haliy-2017]

haliy-2017
i think he has samsung memory on cards

He asks about the cards msi 1060 gaming x plus

[prostor]

hello my  2G card have problem with dag on musicoin
i thought we could mine still a year till 2019

use win7 or other coin with low epoch (Expanse, Ubiq, Soilcoin, ect). win10 reserved ~15% Vram

[sergey1301]

Hi friends! Can this be used with nvidia graphics cards? Will it work? Does 1080ti support? Will Nanopool work with this?

[b10hazzard]

Hello guys!

I am absolutely new to this. So  anything would be helpful. Today i am gonna try diggin from my personal pc as beginner.  Got 16 GB ram ddr4, six core processor and nvidia gtx 970 (4gb). Any tips would be fine any critics also. I am open to learn so i am prepared for critisism if there's any. So is this basicly good enough configuration just to start learning as beginner before i invest in better machine?
So basicly i did what the guy from the video  guide sais. i edited my bat file and still gettin some error i cant solve by myself:
Appreciate your help!

Code:

SSL/TLS encryption is enabled
Pool certificate verified successfully
 DCR: Stratum - Connected (eu1.ethermine.org:5555) (SSL/TLS)
 DCR: Failed to get nonce1 at handshaking
Stratum - reading socket failed 0, disconnect
 DCR: Job timeout, disconnect, retry in 20 sec...
ETH: 07/03/18-14:23:52 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 1.413 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:02
ETH: GPU0 1.413 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 0.000 Mh/s
ETH: 07/03/18-14:23:54 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 1.413 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:02
ETH: GPU0 1.413 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 0.000 Mh/s
ETH: 07/03/18-14:23:56 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 1.413 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:02
ETH: GPU0 1.413 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 0.000 Mh/s
GPU0 t=58C fan=36%
 DCR: Stratum - connecting to 'eu1.ethermine.org' <188.165.239.100> port 5555 (SSL/TLS)
SSL/TLS encryption is enabled
Pool certificate verified successfully
 DCR: Stratum - Connected (eu1.ethermine.org:5555) (SSL/TLS)
 DCR: Failed to get nonce1 at handshaking
Stratum - reading socket failed 0, disconnect
 DCR: Job timeout, disconnect, retry in 20 sec...

Code:

ETH - Total Speed: 2.414 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:09
ETH: GPU0 2.414 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 off
 DCR: Stratum - connecting to 'eu1.ethermine.org' <188.165.220.188> port 5555 (SSL/TLS)
SSL/TLS encryption is enabled
Pool certificate verified successfully
 DCR: Stratum - Connected (eu1.ethermine.org:5555) (SSL/TLS)
 DCR: Failed to get nonce1 at handshaking
Stratum - reading socket failed 0, disconnect
 DCR: Job timeout, disconnect, retry in 20 sec...
ETH: 07/03/18-14:31:36 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 2.413 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:09
ETH: GPU0 2.413 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 off
GPU0 t=60C fan=20%
ETH: 07/03/18-14:31:43 - New job from eu1.ethermine.org:4444
ETH - Total Speed: 2.413 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:10
ETH: GPU0 2.413 Mh/s
 DCR - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0
 DCR: GPU0 off

[haliy-2017]

Who overclocked the video card msi 1060 gaming x plus more than 20mH/s ?(ETH,memory samsung)

[prostor]

Hello guys!
I am absolutely new to this. So  anything would be helpful. Today i am gonna try diggin from my personal pc as beginner.  Got 16 GB ram ddr4, six core processor and nvidia gtx 970 (4gb). Any tips would be fine any critics also. I am open to learn so i am prepared for critisism if there's any. So is this basicly good enough configuration just to start learning as beginner before i invest in better machine?
So basicly i did what the guy from the video  guide sais. i edited my bat file and still gettin some error i cant solve by myself:
Appreciate your help!

claymore recommends this:

TESTED NVIDIA DRIVERS (other versions are untested, they can be worse or better):
9xx cards in Windows 7 x64: just use latest/recent drivers from Nvidia website (for example, 368.81). Note that latest 372.54 is slower than 368.81.
9xx cards in Windows 10 x64: you have to use old drivers (for example, 352.xx) and miner built for cuda6.5.

Who overclocked the video card msi 1060 gaming x plus more than 20mH/s ?(ETH,memory samsung)

1060 3Gb with memory samsung = 23+ M/h
1060 3Gb with hynix = ~20 M/h
1060 with 6Gb version +10% for hashrate

[haliy-2017]

Hello guys!
I am absolutely new to this. So  anything would be helpful. Today i am gonna try diggin from my personal pc as beginner.  Got 16 GB ram ddr4, six core processor and nvidia gtx 970 (4gb). Any tips would be fine any critics also. I am open to learn so i am prepared for critisism if there's any. So is this basicly good enough configuration just to start learning as beginner before i invest in better machine?
So basicly i did what the guy from the video  guide sais. i edited my bat file and still gettin some error i cant solve by myself:
Appreciate your help!

claymore recommends this:

TESTED NVIDIA DRIVERS (other versions are untested, they can be worse or better):
9xx cards in Windows 7 x64: just use latest/recent drivers from Nvidia website (for example, 368.81). Note that latest 372.54 is slower than 368.81.
9xx cards in Windows 10 x64: you have to use old drivers (for example, 352.xx) and miner built for cuda6.5.

Who overclocked the video card msi 1060 gaming x plus more than 20mH/s ?(ETH,memory samsung)

1060 3Gb with memory samsung = 23+ M/h
1060 3Gb with hynix = ~20 M/h
1060 with 6Gb version +10% for hashrate

msi 1060 gaming x PLUS 6Gb???

[prostor]

msi 1060 gaming x PLUS 6Gb???

the type of memory is important. The vendor does not affect this.
1060 6Gb with sams ~25M/h

table for any vendor with OC 1060 6Gb
http://funkyimg.com/i/2Ja8m.png

[haliy-2017]

msi 1060 gaming x PLUS 6Gb???

the type of memory is important. The vendor does not affect this.
1060 6Gb with sams ~25M/h

table for any vendor wint OC 1060 6Gb
https://prnt.sc/k23cuj

Ordinary 1060 6g accelerates to 25, ..., and 1060 6g PLUS gives only 20, .. (memory of the samsung). Did someone else overclock 1060 6g PLUS more than 20, ...?