Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[valev1]

Yes you can

Can I mine eth and verge coin in the same time?

[RAKOT]

Hey folks,

currently mining at 170Mh/s with 6*rx 470 4GB (MSI Gaming X), that's roughly 28.3Mh/s per card with 870W measured from the wall (total power consumption).

We can go a bit higher in terms of hashrate but we only have a 1000W Power Supply and we don't want to take any risks.

In terms of clocks and wattage, our cards are at 1100Mhz and 1050mV for the core and 2050Mhz and 1000mV for the memory.

Few questions:

1. Is it safe to draw ~870W from the wall, 24/7 with a 1000W PSU (Aerocool Gold+)

2. ~170Mh/s for 870W, is it a good ratio or do we have room to optimize the hashrate (without impacting the electricity consumption) ?

1. First of all. 1000W PSU meens that it can support 1000W output load ,  if its gold+  i think you current load is 870*0.95=~820 Watt of 1000 W PSU ability - No problem
2. Im using a lot of 4 Gb 470x cards, and usualy drive them in 1120/900 2000-2100/900 from 28 to 31 Mhs ( depends on vendor). On my mesurement one card eats 110-120 Watt itself.

BR.

[DaFockBro]

Is the project still alife?

Which version of ethminer you guys can recommend me?

[volapyk]

Pascal Coin changed algo to the CPU friendly RandomHash in December 2018
The coin can no longer be dual mined.

I've recently setup Claymore v12.0 for Dual Ethereum+Pascal except I can't find a pool that appears to work with it.

I've tried nanopool, coinotron, & c3pool all with the same results lots of accepted shares and too many rejected shares:

Code:

PASC: 02/24/19-12:50:20 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:20 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:20 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:20 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:20 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: Share rejected (0 ms)!
 PASC: Share rejected (16 ms)!
 PASC: Share rejected (47 ms)!
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: Share rejected (16 ms)!
 PASC: Share rejected (16 ms)!
 PASC: Share rejected (16 ms)!
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: Share rejected (0 ms)!
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: 02/24/19-12:50:21 - SHARE FOUND - (GPU 0)
 PASC: Share rejected (0 ms)!
 PASC: Share rejected (31 ms)!
 PASC: Share rejected (62 ms)!
 PASC: Too many rejects from pool, disconnect...
 PASC: - connection in 20 sec...
ETH: 02/24/19-12:50:21 - New job from us1.ethermine.org:5555
ETH - Total Speed: 28.831 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:04
ETH: GPU0 28.831 Mh/s
 PASC - Total Speed: 182.597 Mh/s, Total Shares: 244, Rejected: 143
 PASC: GPU0 182.597 Mh/s

When Claymore launches, it authorizes to the pools fine, but on the first batch it and everyone after that, it gets disconnected from the pool for too many rejects.  I know they were going through in some fashion in that I got warnings on my c3pool setup of extremely high rejection rates for my account.

I've turned off overclocking on the GPU.  I have a nVidia GTX 1070 that I'm using, I also have a 1060 I'm not using because I'm running Windows 10.

I have been able to connect with nicehash, but that seems to be so little compared to the hashrate 100-200 Mh/s for Pascal.

Any ideas?  Thanks

[keksik]

hello,

i would like to ask some questions:
- when i start to mine, how long it takes to start dev mining?
- when i start stop miner, does it reset counter for dev mining? for example im mining with another miner, then it starts with claymore, after couple hours, it switch back and then after couple hours again with claymore, so does it reset dev mining counter? or another example, im fine tunning and i left miner run for half hour or less, does the counter reset all the time?

thank you

[Altcoinlog]

AltCoinLog about Claymore's Dual Miner



Link to download the original version of the program, instructions for setting up and optimizing software. Basic commands and frequent beginner problems. Ready Bat files for mining.

The article is written in Russian

https://altcoinlog.com/claymore-s-dual-miner-nastroyka/

[RuMiner]

Hello, Mr @Claymore!
There's a new dual mining method described here
Zilminer based on original ethminer works with your dualminer, but it hangs up somitemes while switching miners.
Maybe is it possible to dual mine Zilliqa in dualminer 12.1?  

[keksik]

Hello, Mr @Claymore!
There's a new dual mining method described here
Zilminer based on original ethminer works with your dualminer, but it hangs up somitemes while switching miners.
Maybe is it possible to dual mine Zilliqa in dualminer 12.1?  

what i have seen it has same hash as in ETH, so my assumption is not possible to dual mine as both use same mem mining. it looks to me like mining ETH+ETC at once, you know... but i can be wrong of course, im not a pro.

[RuMiner]

what i have seen it has same hash as in ETH, so my assumption is not possible to dual mine as both use same mem mining. it looks to me like mining ETH+ETC at once, you know... but i can be wrong of course, im not a pro.

ZIL PoW window is just several minutes for about 2 hours. it could switch to ZIL mining like it acts with devfee

[MineStar]

It would be great if the miner would show shares accepted per GPU, something like this:
ETH: GPU0 15.149 Mh/s (20), GPU1 15.083 Mh/s (17), GPU2 15.046 Mh/s (24), GPU3 15.088 Mh/s (10)

[RuMiner]

It would be great if the miner would show shares accepted per GPU

press 's', it does already

[ManDoneKTM]

It would be great if the miner would show shares accepted per GPU

press 's', it does already

Hello guys , wich is the best combo to dual mine with this software ? i tried eth / etc + xvg but doesnt worth it ... another coin / alternative ? i dont pay electricity . 24 amd gpu available .

[Coldstar13]

Anyone get same problem like this please help me. My Claymore run afew min get BSOD then restart.
Claymore ver 12.0
Amd driver 18.6.1
I set core minimum 990, mem 1800, vcdcc 950, cvdcc 950

https://photos.app.[Suspicious link removed]/uwJe24QCi5qD5mcKA

[abhiseshakana]

Anyone get same problem like this please help me. My Claymore run afew min get BSOD then restart.
Claymore ver 12.0
Amd driver 18.6.1
I set core minimum 990, mem 1800, vcdcc 950, cvdcc 950

https://photos.app.[Suspicious link removed]/uwJe24QCi5qD5mcKA

What GPU do you use? and how many GPU did you installed?

I would suggest you should check the risers and try to mine with another mining software, also try to mine with each GPU individually.

There are several factors which can cause BSOD issues. It might be your virtual memory is too low, you should at least try to increase the page file.

[Coldstar13]

Anyone get same problem like this please help me. My Claymore run afew min get BSOD then restart.
Claymore ver 12.0
Amd driver 18.6.1
I set core minimum 990, mem 1800, vcdcc 950, cvdcc 950

https://photos.app.[Suspicious link removed]/uwJe24QCi5qD5mcKA

What GPU do you use? and how many GPU did you installed?

I would suggest you should check the risers and try to mine with another mining software, also try to mine with each GPU individually.

There are several factors which can cause BSOD issues. It might be your virtual memory is too low, you should at least try to increase the page file.

My Rig use Rx470 mining version
The BSOD show "Video TDR Failure (atikmpag.sys"). I duno which file should i download.
https://imgur.com/a/lRLnJNs#r2hLbjp

[vuli1]

install the latest drivers. use DDU to install old ones, than DL  new one.

[elmanager]

Hello, Mr @Claymore!
There's a new dual mining method described here
Zilminer based on original ethminer works with your dualminer, but it hangs up somitemes while switching miners.
Maybe is it possible to dual mine Zilliqa in dualminer 12.1?  

  That would be great!

[big_daddy]

Hello, Mr @Claymore!
There's a new dual mining method described here
Zilminer based on original ethminer works with your dualminer, but it hangs up somitemes while switching miners.
Maybe is it possible to dual mine Zilliqa in dualminer 12.1?  

  That would be great!

Implementing ZIL mining in Claymore dual will be great
Dear Claymore, I hope you will think about it
Tmx.

[elmanager]

Hello, Mr @Claymore!
There's a new dual mining method described here
Zilminer based on original ethminer works with your dualminer, but it hangs up somitemes while switching miners.
Maybe is it possible to dual mine Zilliqa in dualminer 12.1?  

what i have seen it has same hash as in ETH, so my assumption is not possible to dual mine as both use same mem mining. it looks to me like mining ETH+ETC at once, you know... but i can be wrong of course, im not a pro.

   He talks about the native ZIL which is not eth hash and basically it needs its operation mostly once per 2h for a some kind of a lottery which node gonna get the price. I already ran 17 nodes with a rig mining each. A friend set me up the smos dual eth and zil but it crash and reload itself every 2-3 hours.

https://imagebin.ca/v/4a38FMOrxTjw

[big_daddy]

  He talks about the native ZIL which is not eth hash and basically it needs its operation mostly once per 2h for a some kind of a lottery which node gonna get the price. I already ran 17 nodes with a rig mining each. A friend set me up the smos dual eth and zil but it crash and reload itself every 2-3 hours.

In theory, can be implemented in a script inside of Clay's miner
I'm running a "custom" dual with ZIL, I have 3 bat files configured and it works

So, if I can run it like an amateur, Claymore, with his programming skills, I'm sure can give us a more stable solution