Claymore's Dual Ethereum AMD+NVIDIA GPU Miner v15.0 (Windows/Linux)

[hagbase]

Hi
Since a few months I noticed a drop of hashrate on the card of my rigs under Ethos. Previously between 28 and 30mhs on my RX, now no more than 24, even updating Claymore ... Same problem on all my rigs, I wonder if it is normal due to the increase the DAG or not?
Thank you

No, check your settings and update ethOS / miner software.

[1714894376]

1714894376

[1714894376]

1714894376

[arielbit]

Yes I will update my miner to support ProgPow when ETH will be ready to switch to it.

make grin miner too

claymore! claymore! claymore!  ..hehe just like the old days 

[thameur]

hi

is there any news for hashrate drop for R9 390 8g, is not yet set as RX 580, DAG file eat my hashrate 

from 33 Mh/s to 25 !!!

[sernos]

Hi!
I also have more than 10 pieces R9 390 8g and have a problem with hashrate mining ETH

[sxemini]

hi

is there any news for hashrate drop for R9 390 8g, is not yet set as RX 580, DAG file eat my hashrate 

from 33 Mh/s to 25 !!!

There give no news, DAG problem, mine a coin with lower DAG. This problem will never fix and it is very old shit. I write this 1 or 2 times a week and every day the same question.

Read this from phönixminer:

Hi

have there real problems, when mines with R9 390 u. R9 390X GPU's .....
For some months, the hashrate is decreasing continuously from formerly about 33 Mhs / s to about 25.9 Mhs / s even though the R9 390 (X) of the DAG Epoch problem should not be affected at all ...
have any idea to get back 33 Mh/s
Resiste the DAG Epoch

  This is caused by the size of the TLB, which is too small for the current DAG sizes and causes constant eviction from the TLB cache. AMD released the "compute mode" fix for RX4x0 and RX5x0 cards, which simply increased the memory page size. However there is no such fix for 290/390 cards. Probably there is no way to increase the page size on these cards because of hardware limitations but only AMD knows for sure. You can either mine coins with lower DAG (basically everything except ETH and ETC), or accept the hashrate drop (but it will get gradually worse over time).

[l30z1n]

What is the forecast for 4GB cards to stop working? At least another 12 months?

[hascoin]

NVIDIA Cards available: 1
CUDA Driver Version/Runtime Version: 10.0/8.0
GPU #0: GeForce GTX 1050 Ti, 4096 MB available, 6 compute units, capability: 6.1  (pci bus 4:0:0)
Total cards: 1
ETH - connecting to 127.0.0.1:8545
No pool specified for Decred! Ethereum-only mining mode is enabled
ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)
ETH: HTTP SOLO mode
Ethereum HTTP requests time (-etht) is set to 200 ms
Watchdog enabled
Remote management (READ-ONLY MODE) is enabled on port 3333

ETH: http error #7.
ETH: Failed to connect to pool (127.0.0.1:8545), retry in 20 sec...

Help help me please.

I met this error when I mine in a new coin forked on Ethreum.

How to deal with ？

[hascoin]

Hi all I am new here trying to set up for solo mining on a ubuntu machine Eth only. I have the blockchain downloaded and geth running I have set the address in start.bash to 127.0.0.1:8545 I have tried 192.168.1.13:8545 , localhost:8545 but I keep gettimng "ETH: Failed to connect to pool (127.0.0.1:8545), retry in 20 sec...
GPU0 t=44C fan=24%, GPU1 t=45C fan=25%
What am I doing wrong I have read the read me 100 times.

Here is my ./start.bash  ./ethdcrminer64 -epool http://127.0.0.1:8545 -ewal 1c0b92f3aef254a2c122713a8e8a34eb2a760c77 -mode 1

It works ok with the default pool but I would like to solo. It reads the graphics catds OK and I have the right drivers.

OK it is working now the problem was how I was running geth. all good now

Congratulate on your success,But I am still in the similiar issues.I am solo on the WIN10 with GPU.
LOOKING FOR A HELP.
Many many many thanks to you and everybody willing to help me.I can offer a bounty for this issue.

[astraleureka]

Is the pool server listening on port 8545 ?

[hascoin]

Is the pool server listening on port 8545 ?

how to set port? is there a conf file in the ethreum folder in %appdata% like the bitcoin.

[hascoin]

why??? no one no replies for so long time?

feel not good at all now.

[RivAngE]

why??? no one no replies for so long time?

feel not good at all now.

Reply to what? "How to set a port"?

Is the pool server listening on port 8545 ?

how to set port? is there a conf file in the ethreum folder in %appdata% like the bitcoin.

I might have misunderstood something, but if you're talking about the miner's settings then it's put after the pool's address like this: -epool eu1.ethermine.org:4444
Is this really what you were asking?!

[d_fernandez]

Hi guys, please my apologies in advance if my question does not fit here, but if that's the case i please ask the mods to move this message to where it belongs.


Up to 2 weeks ago (more or less) i could mine without any problem with version 11.9 of claymore. At a certain moment the mining just stopped and from that time till now i get the same error:



20:24:32:174   16a4   Check and remove old log files...
20:24:32:174   16a4   args: -epool eu1.ethermine.org:14444 -ewal mywalletadress.AresPC -epsw x -esm 1 -mode 1 -asm 0 -estale 0 -dcri 0 -etha 1 -eres 0
20:24:32:174   16a4   
20:24:32:174   16a4   ÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»
20:24:32:174   16a4   º                Claymore's Dual GPU Miner - v12.0               º
20:24:32:174   16a4   º              ETH + DCR/SIA/LBC/PASC/BLAKE2S/KECCAK             º
20:24:32:174   16a4   ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ
20:24:32:190   16a4   
20:24:32:190   16a4   b615
20:24:32:393   16a4   ETH: 1 pool is specified
20:24:32:393   16a4   Main Ethereum pool is eu1.ethermine.org:14444
20:24:33:924   16a4   OpenCL platform: AMD Accelerated Parallel Processing
20:24:33:940   16a4   OpenCL initializing...

20:24:33:940   16a4   AMD Cards available: 1
20:24:33:940   16a4   GPU #0: Ellesmere (Radeon RX 580 Series), 8192 MB available, 36 compute units (pci bus 1:0:0)
20:24:33:940   16a4   GPU #0 recognized as Radeon RX 480/580
20:24:33:940   16a4   POOL/SOLO version
20:24:33:940   16a4   Platform: Windows
20:24:34:518   16a4   start building OpenCL program for GPU 0...
20:24:34:580   16a4   done
20:24:34:705   16a4   Error: AMDIL doesn't support device Ellesmere.
Target is invalid.
Error: Compilation from LLVMIR binary to IL text failed!
20:24:34:705   16a4   Cannot build OpenCL program for GPU 0
20:24:35:736   16a4   GPU #0: set -etha as 1 (ETH algo for slow cards)
20:24:35:736   16a4   cudaGetDeviceCount failed (35, CUDA driver version is insufficient for CUDA runtime version), probably no CUDA devices
20:24:35:736   16a4   No NVIDIA CUDA GPUs detected.
20:24:35:736   16a4   Total cards: 1
20:24:37:783   16a4   No NVIDIA cards in the list, NVML library will not be used.
20:24:38:908   16a4   SSL: Imported 62 certificates from local storage
20:24:38:955   1ed4   ETH: Stratum - connecting to 'eu1.ethermine.org' <172.65.207.106> port 14444 (unsecure)
20:24:39:018   1ed4   sent: {"id":2,"jsonrpc":"2.0","method":"eth_login","params":["0x364a29f791c4ae2f87dabb236e66ae5bbbeb661d.AresPC","x"]}

20:24:39:018   1ed4   ETH: Stratum - Connected (eu1.ethermine.org:14444) (unsecure)
20:24:39:033   16a4   ETHEREUM-ONLY MINING MODE ENABLED (-mode 1)

20:24:39:033   16a4   ETH: qtminer stratum mode
20:24:39:033   16a4   Watchdog enabled
20:24:39:033   16a4   Remote management (READ-ONLY MODE) is enabled on port 3333
20:24:39:033   16a4   

20:24:39:502   1ed4   buf: {"id":2,"jsonrpc":"2.0","result":true}

20:24:39:502   1ed4   ETH: Authorized
20:24:39:502   1ed4   sent: {"id":3,"jsonrpc":"2.0","method":"eth_getWork","params":[]}

20:24:39:768   1ed4   buf: {"id":3,"jsonrpc":"2.0","result":["0x7555ffc6b0d8466394d3f73424f0fe06cf0b14425386ff5dcf7487ce12184d92","0xfc07df566e435375b9a66bc1e5c35e40b5e69814dd4855b0093944698f4f26c4","0x0112e0be826d694b2e62d01511f12a6061fbaec8bc02357593e70e52ba","0x6c6e0b"]}

20:24:39:815   1f9c   Setting DAG epoch #236...
20:24:46:986   1f9c   Setting DAG epoch #236 for GPU0
20:24:46:986   1f9c   Create GPU buffer for GPU0
20:24:47:268   1f9c   GPU0, OpenCL error -48 (0) - cannot create DAG on GPU

20:24:47:690   1ed4   buf: {"id":0,"jsonrpc":"2.0","result":["0x0840e6eed72c9325ec10b4e1a66b9128f6f1883a0f0cf6c35f22c192bdf0f550","0xfc07df566e435375b9a66bc1e5c35e40b5e69814dd4855b0093944698f4f26c4","0x0112e0be826d694b2e62d01511f12a6061fbaec8bc02357593e70e52ba","0x6c6e0c"]}
{"id":0,"jsonrpc":"2.0","result":["0x1f17a532ed2b01718204a18e105c7202d4ab69b6d10579f6c08768944172db8c","0xfc07df566e435375b9a66bc1e5c35e40b5e69814dd4855b0093944698f4f26c4","0x0112e0be826d694b2e62d01511f12a6061fbaec8bc02357593e70e52ba","0x6c6e0c"]}

20:24:47:690   1ed4   remove first packet 248
20:24:47:690   1ed4   ETH: 01/21/19-20:24:47 - New job from eu1.ethermine.org:14444
20:24:47:690   1ed4   target: 0x0000000112e0be82 (diff: 4000MH), epoch 236(2.84GB)
20:24:47:690   1ed4   ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
20:24:47:690   1ed4   ETH: GPU0 0.000 Mh/s
20:24:50:283   1f9c   Set global fail flag, failed GPU0
20:24:50:283   1f9c   GPU 0 failed
20:24:50:283   1fa0   Setting DAG epoch #236 for GPU0
20:24:50:346   1fa0   GPU0, OpenCL error -48 (0) - cannot create DAG on GPU

20:24:53:361   1fa0   Set global fail flag, failed GPU0
20:24:53:361   1fa0   GPU 0 failed
20:24:57:487   1ed4   buf: {"id":0,"jsonrpc":"2.0","result":["0xe35c779914934a3f3e080f987a1643c633b49ded6596495d6eeb47e94e3ed668","0xfc07df566e435375b9a66bc1e5c35e40b5e69814dd4855b0093944698f4f26c4","0x0112e0be826d694b2e62d01511f12a6061fbaec8bc02357593e70e52ba","0x6c6e0c"]}

20:24:57:487   1ed4   ETH: 01/21/19-20:24:57 - New job from eu1.ethermine.org:14444
20:24:57:487   1ed4   target: 0x0000000112e0be82 (diff: 4000MH), epoch 236(2.84GB)
20:24:57:487   1ed4   ETH - Total Speed: 0.000 Mh/s, Total Shares: 0, Rejected: 0, Time: 00:00
20:24:57:487   1ed4   ETH: GPU0 0.000 Mh/s
20:24:59:783   1ed4   sent: {"id":6,"jsonrpc":"2.0","method":"eth_submitHashrate","params":["0x0", "0x00000000000000000000000000000000000000000000000000000000c358acb8"]}

20:25:00:049   1ed4   buf: {"id":6,"jsonrpc":"2.0","result":true}


Then I tried to upgrade the claymore version to 12.0 thinking that maybe there was something that had changed but in fact nothing did.
I have only one MSI RX 580 with original updated (from MSI official webpage) bios, and the virtual memory is at 70 gb (I put that at a high value to test if paging was bothering but still no good) and Windows x64.

The drivers of amd are version 19.1.1 but earlier versions work the same (not working I mean).

Anybody could have a reason why suddenly it stopped working?

Thanks.

[big_daddy]

[...]

Then I tried to upgrade the claymore version to 12.0 thinking that maybe there was something that had changed but in fact nothing did.
I have only one MSI RX 580 with original updated (from MSI official webpage) bios, and the virtual memory is at 70 gb (I put that at a high value to test if paging was bothering but still no good) and Windows x64.

The drivers of amd are version 19.1.1 but earlier versions work the same (not working I mean).

Anybody could have a reason why suddenly it stopped working?

Thanks.

Try this:

DDU, restart
Install the Blockchain driver
Patch it
Add this at the beginning of your start.bat file->
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_FORCE_64BIT_PTR 0
setx GPU_SINGLE_ALLOC_PERCENT 100

or

Use any 18.x.x driver version + Compute mode on

[d_fernandez]

Try this:

DDU, restart
Install the Blockchain driver
Patch it
Add this at the beginning of your start.bat file->
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_FORCE_64BIT_PTR 0
setx GPU_SINGLE_ALLOC_PERCENT 100

or

Use any 18.x.x driver version + Compute mode on

I already did that before asking in this forum, but no solution.

The bat file is written with those lines too.

[hascoin]

why??? no one no replies for so long time?

feel not good at all now.

Reply to what? "How to set a port"?

Is the pool server listening on port 8545 ?

how to set port? is there a conf file in the ethreum folder in %appdata% like the bitcoin.

I might have misunderstood something, but if you're talking about the miner's settings then it's put after the pool's address like this: -epool eu1.ethermine.org:4444
Is this really what you were asking?!

Thanks for your kindly reply,my questions is the same with beammeup

Quote from: beammeup on July 29, 2016, 02:25:12 PM
Hi all I am new here trying to set up for solo mining on a ubuntu machine Eth only. I have the blockchain downloaded and geth running I have set the address in start.bash to 127.0.0.1:8545 I have tried 192.168.1.13:8545 , localhost:8545 but I keep gettimng "ETH: Failed to connect to pool (127.0.0.1:8545), retry in 20 sec...
GPU0 t=44C fan=24%, GPU1 t=45C fan=25%
What am I doing wrong I have read the read me 100 times.

Could you please tell me the best way to resolve this issue.

[nick_fc]

Hello.
Yesturday evening 1 of 6 1063 cards in my rig start mining with lower speed (5Mh)
Seems like DAG is again become too big.
in few days  with new epoch 1063 will stop mining at all

P.S. win 7

[big_daddy]

Try this:

DDU, restart
Install the Blockchain driver
Patch it
Add this at the beginning of your start.bat file->
setx GPU_MAX_ALLOC_PERCENT 100
setx GPU_USE_SYNC_OBJECTS 1
setx GPU_MAX_HEAP_SIZE 100
setx GPU_FORCE_64BIT_PTR 0
setx GPU_SINGLE_ALLOC_PERCENT 100

or

Use any 18.x.x driver version + Compute mode on

I already did that before asking in this forum, but no solution.

The bat file is written with those lines too.

It can be an issue in W10, by installing the last driver version probably you got the automatic update switched on, by the amd installer
Try to disable that first, than DDU and try again

https://www.laptopmag.com/articles/disable-automatic-driver-downloads-on-windows-10
https://www.windowscentral.com/how-disable-automatic-driver-updates-windows-10

[naikmyeong]

Yes I will update my miner to support ProgPow when ETH will be ready to switch to it.

Will you still support ProgPoW for your miner if Ethereum Foundation doesn't accept switching to ProgPoW and therefore some new Ethereum Hardfork coin launch with ProgPoW switch?

[cobraq]

is it  will be work on amd cards dual mining eth + btm ?