spiccioli
Legendary
Offline
Activity: 1378
Merit: 1003
nec sine labore
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 06:22:08 AM |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
How many GH/s are you getting at 450? Three or four modules unit? spiccioli
|
|
|
|
driksson
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 07:55:54 AM |
|
Sure can.
Hi, if you have time, would 350-400 or even 350-450 be an ok autosetting in a 20dgr airconditioned room? for an avalon batch 2 3 module unit.
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 09:22:33 AM |
|
Sure can.
Hi, if you have time, would 350-400 or even 350-450 be an ok autosetting in a 20dgr airconditioned room? for an avalon batch 2 3 module unit. Unless you have done hardware modifications, you will not find any stock avalon under any conditions that will run much better than 360. The firmware posted so far already allows for speeds up to 450.
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
driksson
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 10:08:51 AM |
|
Sure can.
Hi, if you have time, would 350-400 or even 350-450 be an ok autosetting in a 20dgr airconditioned room? for an avalon batch 2 3 module unit. Unless you have done hardware modifications, you will not find any stock avalon under any conditions that will run much better than 360. The firmware posted so far already allows for speeds up to 450. Thanks for your time. Ok, no stock mods done, it even has stock psu. So i will put it to auto 300-360? or 340-360? its in a very cold room, but maybe its not enough.
|
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 02:55:33 PM Last edit: August 23, 2013, 07:02:06 PM by S M I L Y |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
How many GH/s are you getting at 450? Three or four modules unit? spiccioli At the moment I am running only 2 modules while i finish the waterblocks on the other 2. Im showing 71Ghs on 2 modules at 450Mhz. BTCGuild is showing exactly 75Ghs ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FPyvA95T.jpg&t=665&c=KuyTDVUX7C7fdQ)
|
|
|
|
creativex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 07:37:58 PM |
|
Unless you have done hardware modifications, you will not find any stock avalon under any conditions that will run much better than 360. The firmware posted so far already allows for speeds up to 450. Hi ckolivas. I'd like to thank you for your excellent work on Avalon firmware revisions. 20130821 has worked a treat on my batch 1 & 2 rigs. I'm having difficulty with your latest releases on batch 3, 4 module rigs however, and I apologize if this has been discussed and I missed it. These are restarting cgminer when temp 2 = > 60. I've tried every firmware from 20130703 to 20130821 and they all exhibit this behavior. The only firmware that seems to work properly on these rigs is their factory firmware 20130723. Do you have any idea how this issue can be resolved? Cheers.
|
|
|
|
Tigggger
Legendary
Offline
Activity: 1098
Merit: 1000
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 08:28:11 PM |
|
I'm having difficulty with your latest releases on batch 3, 4 module rigs however, and I apologize if this has been discussed and I missed it. These are restarting cgminer when temp 2 = > 60. I've tried every firmware from 20130703 to 20130821 and they all exhibit this behavior. The only firmware that seems to work properly on these rigs is their factory firmware 20130723. Do you have any idea how this issue can be resolved?
Have you used --avalon-temp 70 --avalon-cutoff 90 ? These need to be added to the 'more options' for batch 3, not had any restarts on mine except when upgading the firmware.
|
|
|
|
creativex
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 08:45:02 PM |
|
Hi Tigggger. I did try --avalon-temp 70 as that's what was specified for the b3s by default. I don't recall setting the cutoff temp though. I'll give that a shot, thanks.
Edit: That worked a treat, thanks!
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 10:24:03 PM |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
There's a special one-off firmware just for you that lifts the limit to 1000 here: http://ck.kolivas.org/apps/cgminer/temp/
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 11:06:19 PM |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
There's a special one-off firmware just for you that lifts the limit to 1000 here: http://ck.kolivas.org/apps/cgminer/temp/AWESOME!! THANK YOU!!!
|
|
|
|
BitCoiner2012
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 23, 2013, 11:10:03 PM |
|
What kind of hash rates are people achieving with Batch 2s now? I'm hanging out at 79-83, around 350 freq. Is the new firmware of interest to me?
|
BTC Long.
|
|
|
jermwerty
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 12:07:14 AM |
|
Has anyone had the problem where the box will be just fine for the first day, but then hashrate just drops off to ~60Ghash? I have a 3-mod B2 and 4-mod B3 that both do this when using auto with a range of 325-350 after a while. What is interesting is the hashrate reported on the GUI stays the same, but the pool shows the reduced rate. I also end up noticing a large amount of HW errors it seems during this same time (one time I had a whole module seem to stop reporting shares). (all Aug firmwares)
Funny thing is, if I set it to 340mhz max the errors drop to 0.6-0.8%. 345mhz shows around 1.9% or so. Seems to be the same on both boxes. I have an AC unit blowing directly into the intakes and the B2 runs 45C and the B3 runs 58C. Fans are default speeds, it almost seemed like upping them manually caused more issues?
At this point I am leaning towards just setting 335mhz or something and say forget it, I had weeks of uptime at 300mhz clocks and just got around to OCing as of late.
|
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 12:42:52 AM |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
There's a special one-off firmware just for you that lifts the limit to 1000 here: http://ck.kolivas.org/apps/cgminer/temp/This firmware isnt working past 450. CGMiner API log shows: [Firmware Version] => 20130824 cgminer-bdac063+ luci-d854edc+ cgminer-openwrt-packages-800cc58 Socket connect failed: Connection refused Thanks again for all your work!
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 12:46:00 AM |
|
Yes perfectly stable .49% hw error at 41c Batch3
could you lift that 450 limit easily?
Thanks!
There's a special one-off firmware just for you that lifts the limit to 1000 here: http://ck.kolivas.org/apps/cgminer/temp/This firmware isnt working past 450. CGMiner API log shows: [Firmware Version] => 20130824 cgminer-bdac063+ luci-d854edc+ cgminer-openwrt-packages-800cc58 Socket connect failed: Connection refused Thanks again for all your work! Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 12:53:19 AM |
|
Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
In the web GUI in the "Chip Frequency(Default: 300)" field Is where I have been setting the frequency. The only "More options" I have set is "--avalon-fan 50"
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 12:58:03 AM |
|
Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
In the web GUI in the "Chip Frequency(Default: 300)" field Is where I have been setting the frequency. The only "More options" I have set is "--avalon-fan 50" Try what I suggested, and put your range you're interested in More Options as well: --avalon-auto --avalon-freq 450-500 or something
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 01:05:52 AM |
|
Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
In the web GUI in the "Chip Frequency(Default: 300)" field Is where I have been setting the frequency. The only "More options" I have set is "--avalon-fan 50" Try what I suggested, and put your range you're interested in More Options as well: --avalon-auto --avalon-freq 450-500 or something Still doesn't work More options: --avalon-auto --avalon-freq 450-465 --avalon-fan 50 What am I supposed to do with the main frequency field? Both with Blank and 450mhz the system doesn't start.
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 01:34:06 AM |
|
Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
In the web GUI in the "Chip Frequency(Default: 300)" field Is where I have been setting the frequency. The only "More options" I have set is "--avalon-fan 50" Try what I suggested, and put your range you're interested in More Options as well: --avalon-auto --avalon-freq 450-500 or something Still doesn't work More options: --avalon-auto --avalon-freq 450-465 --avalon-fan 50 What am I supposed to do with the main frequency field? Both with Blank and 450mhz the system doesn't start. There is no reason it wouldn't start with the same settings you used previously. Try those first, and then add just --avalon-auto to the More Options box. Sometimes people are impatient and it can take it up to 2 mins before you start seeing the output from cgminer.
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
S M I L Y
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 113
Merit: 10
https://www.chynge.net/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 01:39:22 AM |
|
Did you try it with --avalon-auto without other parameters? It might just be the web interface that doesn't allow it.
In the web GUI in the "Chip Frequency(Default: 300)" field Is where I have been setting the frequency. The only "More options" I have set is "--avalon-fan 50" Try what I suggested, and put your range you're interested in More Options as well: --avalon-auto --avalon-freq 450-500 or something Still doesn't work More options: --avalon-auto --avalon-freq 450-465 --avalon-fan 50 What am I supposed to do with the main frequency field? Both with Blank and 450mhz the system doesn't start. There is no reason it wouldn't start with the same settings you used previously. Try those first, and then add just --avalon-auto to the More Options box. Sometimes people are impatient and it can take it up to 2 mins before you start seeing the output from cgminer. Its definitely not working. with the Main frequency field at 440 and the Options field as "--avalon-auto --avalon-freq 440-455 --avalon-fan 50" Waited for at least 5 min here. Adjusted only the "--avalon-freq 440-455" down to "--avalon-freq 440-450" and the system starts within 30sec. Is the an SSH command line only method I could try?
|
|
|
|
-ck
Legendary
Offline
Activity: 4214
Merit: 1644
Ruu \o/
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 24, 2013, 01:41:23 AM |
|
There is no reason it wouldn't start with the same settings you used previously. Try those first, and then add just --avalon-auto to the More Options box. Sometimes people are impatient and it can take it up to 2 mins before you start seeing the output from cgminer.
Its definitely not working. with the Main frequency field at 440 and the Options field as "--avalon-auto --avalon-freq 440-455 --avalon-fan 50" Waited for at least 5 min here. Adjusted only the "--avalon-freq 440-455" down to "--avalon-freq 440-450" and the system starts within 30sec. Is the an SSH command line only method I could try? Edited, kept highlighting wrong part.
|
Developer/maintainer for cgminer, ckpool/ckproxy, and the -ck kernel 2% Fee Solo mining at solo.ckpool.org -ck
|
|
|
|