SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching

[sharix80]

my rig just freezes and reboots with the new version 1.8.0...cards are rx550.
it works fine with 1.7.9

Give more info, "just freezes" isnt too much info, you must admit that..

already tried new version on 2 my rigs, all are on rx550s, i edit v4 to v8 in start.bat, miner starts, compiles kernels but then just freezes and rig goes to reboot...should i edit something else except v4>v8 ?? i have 18.6.1&18.5.2 radeon drivers and win10 1803.

Try setting up gpu's with gpu_conf by hand, maybe you need to use lower intensity values than the auto setup gives.

Yes its true,system freezes, same thing to me using rx550 2GB, i have also rx550 4GB and works fine, maybe 2GB Gpu's are out.

Use 27 intensity in config. If you start SRB on RX550 with auto setup, miner gives 29 intensity. Thats too much for RX550 2gb. This is the reason why rig freezes and goes to reboot.

[abg00]

hi dok
litle trouble on turtle and upx with old 2gb card
-i 0 work poor. set 172. need change 0 to 36

[Csouza]

What is best setings for vegas56@64 on graft ?


                                        core    mem       HS
Radeon RX 570 4GB      1200     1850   1126

Radeon RX 580 4GB      1150   2050   1154

Radeon RX Vega           1450     1100   1576

        570 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
   580 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
      Vega "intensity" : 112, "worksize" : 16, "threads" : 2, "fragments" : 8},

[4ward]

--cgpuintensity value (gpu intensity, comma separated values)
--cgputhreads value (number of gpu threads, comma separated values)
--cgpuworksize value (gpu worksize, comma separated values)

do those need to always be comma separated values or a single value will be used for all cards?

[GKumaran]

What is best setings for vegas56@64 on graft ?


                                        core    mem       HS
Radeon RX 570 4GB      1200     1850   1126

Radeon RX 580 4GB      1150   2050   1154

Radeon RX Vega           1450     1100   1576

        570 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
   580 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
      Vega "intensity" : 112, "worksize" : 16, "threads" : 2, "fragments" : 8},

you can get 2500+ hr if you run it in auto-  intensity : 0, double_threads=true

[Csouza]

What is best setings for vegas56@64 on graft ?


                                        core    mem       HS
Radeon RX 570 4GB      1200     1850   1126

Radeon RX 580 4GB      1150   2050   1154

Radeon RX Vega           1450     1100   1576

        570 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
   580 "intensity" : 59, "worksize" : 16, "threads" : 2, "fragments" : 8},
      Vega "intensity" : 112, "worksize" : 16, "threads" : 2, "fragments" : 8},

you can get 2500+ hr if you run it in auto-  intensity : 0, double_threads=true

I have a mixed rig with 2 rx580 and 4 Vega56@54 in auto the miner crashes, they set 112 intensity for RX580 4GB.

[GKumaran]

Not sure about the rx, but vega is rock stable, im running 6 vega 64, with almost the same settings as you in auto.

[abhiseshakana]

I have a mixed rig with 2 rx580 and 4 Vega56@54 in auto the miner crashes, they set 112 intensity for RX580 4GB.

You should try to increase the virtual memory (page file) and make sure the HBCC segment had been disabled.

Btw, which driver version did you installed?

[Coindgr]

Graft just forked yesterday to new cryptonight algo, is this updated?

[Rabotaet]

Пoдcкaжитe. Mнe нe пoнятнo кaкoй aлгopитм yкaзывaть в кoнфигe для бyдyщeгo фopкa мoнepo?
B фaйлe ReadMe этo:
SUPPORTED ALGOS:
----------------
Cryptonight Alloy [alloy]
Cryptonight ArtoCash [artocash]
Cryptonight B2N [b2n]
Cryptonight BitTubeV2 [bittubev2]
Cryptonight Conceal [conceal]
Cryptonight Dark [dark]
Cryptonight Fast [fast]
Cryptonight Fast2 [fast2]
Cryptonight Fest [festival]
Cryptonight Gpu [gpu]
Cryptonight Graft [graft]
Cryptonight Haven [haven]
Cryptonight Heavy [heavy]
Cryptonight Hospital [hospital]
Cryptonight Hycon [hycon]
Cryptonight Italo [italo]
Cryptonight Lite [lite]
Cryptonight Lite V7 [litev7]
Cryptonight MarketCash [marketcash]
Cryptonight Mox [mox]
Cryptonight [normal]
Cryptonight V4 (R) [normalv4]
Cryptonight V4_64 [normalv4_64]
Cryptonight V7 [normalv7]
Cryptonight V8 [normalv8]
Cryptonight StelliteV4 [stellitev4]
Cryptonight StelliteV5-V8-V9 [stellitev8]
Cryptonight Swap [swap]
Cryptonight Turtle [turtle]
Cryptonight Upx [upx]
Cryptonight Webchain [webchain]
Cryptonight Wownero [wownero]
Cryptonight Xcash [xcash]
Cryptonight Zelerius [zelerius]
И гдe здecь Cryptonight R ??

[Kaezar]

Пoдcкaжитe. Mнe нe пoнятнo кaкoй aлгopитм yкaзывaть в кoнфигe для бyдyщeгo фopкa мoнepo?
B фaйлe ReadMe этo:
SUPPORTED ALGOS:
----------------
...
Cryptonight [normal]
Cryptonight V4 (R) [normalv4]
Cryptonight V4_64 [normalv4_64]
Cryptonight V7 [normalv7]
Cryptonight V8 [normalv8]

И гдe здecь Cryptonight R ??

Code:

Cryptonight V4 (R) [normalv4]
Cryptonight V4_64 [normalv4_64]

A этo ктo?)))
Укaзывaй normalv4

[borox]

What is the difference in the implementation of

Cryptonight Fast2 [fast2]

.. and ..

Cryptonight StelliteV5-V8-V9 [stellitev8]

.. shouldn't it be the same Cryptonight-Half algorithm for Masari and Stellite?

[Csouza]

I have a mixed rig with 2 rx580 and 4 Vega56@54 in auto the miner crashes, they set 112 intensity for RX580 4GB.

You should try to increase the virtual memory (page file) and make sure the HBCC segment had been disabled.

Btw, which driver version did you installed?

Vmemory is on 32GB and HBCC is on. I ran this RIG more than an year.

The problem is, SRBMiner in auto config mode, sets intensity 112 for RX580 that have only 4GB causing miner dont start, because 112 intensity needs 8GB vram.

Anyone can post config for vega, it can be seen at the top of the SRBMiner screen.

[keksik]

hello, tomorrow is monero fork cryptonight R and can someone recommend me settings for new fork for amd rx 580 4/8gb rig?
how the config file should looks like? i was mining eth all the time 1150/850 // 2000+-/850 stable.

thank you for all advises.

EDIT: im using default bat from 1st page so it sohuld switch automaticaly and i left config on auto.
SRBMiner-CN.exe --enablecoinforking --config Config\config-normalv8.txt --pools pools.txt
 
my concerns is however pool.txt. i will also use nanopool, however my adress from bittrex is a bit shortet and i have "tag" instead of paymentID. is that ok if i use wallet.tag instead of wallet.paymentID setup?

[doktor83]

hello, tomorrow is monero fork cryptonight R and can someone recommend me settings for new fork for amd rx 580 4/8gb rig?
how the config file should looks like? i was mining eth all the time 1150/850 // 2000+-/850 stable.

thank you for all advises.

EDIT: im using default bat from 1st page so it sohuld switch automaticaly and i left config on auto.
SRBMiner-CN.exe --enablecoinforking --config Config\config-normalv8.txt --pools pools.txt
 
my concerns is however pool.txt. i will also use nanopool, however my adress from bittrex is a bit shortet and i have "tag" instead of paymentID. is that ok if i use wallet.tag instead of wallet.paymentID setup?

As long as the wallet address starts with '4' you are ok.

Example :

1.

Config\config-normalv8.txt -> set it up if you want
Config\config-normalv4.txt -> set it up if you want

2.

Make sure you have both normalv8 and normalv4 set in algos.txt

Code:

	{
		"algo" : "normalv8",
		"config" : "Config\\config-normalv8.txt",
		"hashrate" : 1,
		"startup_script": ""
	},
	{
		"algo" : "normalv4",
		"config" : "Config\\config-normalv4.txt",
		"hashrate" : 1,
		"startup_script": ""
	}

3.

pools.txt

Code:

{
"pools" :
[
	{
		"pool" : "xmr-eu1.nanopool.org:14444", 
		"wallet" : "4A5hJyu2FvuM2azexYssHW2odrNCNWVqLLmzCowrA57xGJLNufXfzVgcMpAy3YWpzZSAPALhVH4Ed7xo6RZYyw2bUtbm12g.donation", 
		"password" : "x"
	},
	{
		"pool" : "xmr-eu2.nanopool.org:14444", 
		"wallet" : "4A5hJyu2FvuM2azexYssHW2odrNCNWVqLLmzCowrA57xGJLNufXfzVgcMpAy3YWpzZSAPALhVH4Ed7xo6RZYyw2bUtbm12g.donation", 
		"password" : "x"
	}
]
}

4.

start.bat

Code:

SRBMiner-CN.exe --enablecoinforking --config Config\config-normalv8.txt --pools pools.txt

If you downloaded 1.8.0 and did not touch algos.txt and Config folder, then you can skip steps 1,2 because it is all pre-set.

[Iamtutut]

How can I prevent the miner compile binaries for my IGP ? I have a Ryzen 2400G which as use as main display.

With this config file:

{
"cryptonight_type" : "graft",   
"intensity" : 58,   
"double_threads" : true,   
"shutdown_temperature" : 80,   
"off_temperature" : 80   
}

"gpu_conf" :
[
   { "id" : 0, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 1, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 2, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 3, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
]


The miner won't start.

Thanks

[doktor83]

How can I prevent the miner compile binaries for my IGP ? I have a Ryzen 2400G which as use as main display.

With this config file:

{
"cryptonight_type" : "graft",   
"intensity" : 58,   
"double_threads" : true,   
"shutdown_temperature" : 80,   
"off_temperature" : 80   
}

"gpu_conf" :
[
   { "id" : 0, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 1, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 2, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
   { "id" : 3, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
]


The miner won't start.

Thanks

Code:

{
"cryptonight_type" : "graft",	
"intensity" : 58,	
"double_threads" : true,	
"shutdown_temperature" : 80,	
"off_temperature" : 80,
"gpu_conf" : 
[ 
	{ "id" : 0, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
	{ "id" : 1, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
	{ "id" : 2, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
	{ "id" : 3, "intensity" : 58, "worksize" : 8, "threads" : 2, "fragments" : 8},
]
}

[Iamtutut]

It's working, thank you for the very fast answer !

[georggor]

Hey.Which command helps reduce the amount of stale share.

[keksik]

hello, tomorrow is monero fork cryptonight R and can someone recommend me settings for new fork for amd rx 580 4/8gb rig?
how the config file should looks like? i was mining eth all the time 1150/850 // 2000+-/850 stable.

thank you for all advises.

EDIT: im using default bat from 1st page so it sohuld switch automaticaly and i left config on auto.
SRBMiner-CN.exe --enablecoinforking --config Config\config-normalv8.txt --pools pools.txt
 
my concerns is however pool.txt. i will also use nanopool, however my adress from bittrex is a bit shortet and i have "tag" instead of paymentID. is that ok if i use wallet.tag instead of wallet.paymentID setup?

As long as the wallet address starts with '4' you are ok.

Example :

1.

Config\config-normalv8.txt -> set it up if you want
Config\config-normalv4.txt -> set it up if you want

2.

Make sure you have both normalv8 and normalv4 set in algos.txt

Code:

	{
		"algo" : "normalv8",
		"config" : "Config\\config-normalv8.txt",
		"hashrate" : 1,
		"startup_script": ""
	},
	{
		"algo" : "normalv4",
		"config" : "Config\\config-normalv4.txt",
		"hashrate" : 1,
		"startup_script": ""
	}

3.

pools.txt

Code:

{
"pools" :
[
	{
		"pool" : "xmr-eu1.nanopool.org:14444", 
		"wallet" : "4A5hJyu2FvuM2azexYssHW2odrNCNWVqLLmzCowrA57xGJLNufXfzVgcMpAy3YWpzZSAPALhVH4Ed7xo6RZYyw2bUtbm12g.donation", 
		"password" : "x"
	},
	{
		"pool" : "xmr-eu2.nanopool.org:14444", 
		"wallet" : "4A5hJyu2FvuM2azexYssHW2odrNCNWVqLLmzCowrA57xGJLNufXfzVgcMpAy3YWpzZSAPALhVH4Ed7xo6RZYyw2bUtbm12g.donation", 
		"password" : "x"
	}
]
}

4.

start.bat

Code:

SRBMiner-CN.exe --enablecoinforking --config Config\config-normalv8.txt --pools pools.txt

If you downloaded 1.8.0 and did not touch algos.txt and Config folder, then you can skip steps 1,2 because it is all pre-set.

thx, i have double checked my bittrex adress and seems i did mistake and correct it. my address is now starting with 4 and got also paymentID:) thx for your help, i have 1.8.0 and did not touch algos/config so i shoudl be fine, tested it and it started mining. well i have a bit less hash, like all cards under 1000H/s with all rx 580 4/8GB, but im sure it all depends on timings used in my card bios and mem type. mostly hynix.
what is the best intensity, worksize, fragments,... or rx 580 4/8g gb cards?