SRBMiner Cryptonight AMD GPU Miner V1.9.3 - native algo switching

[wyzdic]

Nah, CF is disabled, as well as HBCC. I even went through the steps to enable the compute mode, but nothing helped.

You need 18.5.1  18.5.2  18.6.1 drivers.
Do not use 18.7.1+ drivers.

[Bakhtra]

Hello,
I got strange problem. Kind like pyramid problem, previous card always lower than next card.
[2018-10-22 17:56:05] GPU0 :    1512 H/s [T: 62c, RPM: 3673, CC: 1200 MHz, MC: 900 MHz][BUS:21] >> vega56
[2018-10-22 17:56:05] GPU1 :    1523 H/s [T: 68c, RPM: 3666, CC: 1050 MHz, MC: 800 MHz][BUS:18] >> vega56
[2018-10-22 17:56:05] GPU2 :    1698 H/s [T: 63c, RPM: 3693, CC: 1202 MHz, MC: 900 MHz][BUS:24] >> vega56
[2018-10-22 17:56:05] GPU3 :    1694 H/s [T: 62c, RPM: 3679, CC: 1350 MHz, MC: 950 MHz][BUS:15] >> vega56
[2018-10-22 17:56:05] GPU4 :    1969 H/s [T: 65c, RPM: 3698, CC: 1350 MHz, MC: 1100 MHz][BUS:9] >> vega64
[2018-10-22 17:56:05] Total:    8396 H/s

I'm using windows 10 1803 and 18.6.1 adrenalin driver.
I try even install clean windows etc still error like that. Anyone can help?
Thank you.
==
Oh I forgot to mention, i just lower my core for make it to stay below 70c, and even i make it same as other 1350 900, the problem still persist.

Your vegas temperature is too high.
If your core is 68c, HBM and Hotspot is 78c+. HBM and hotspots are always 10c higher than the core temperature.
This is very dangerous, Keep the HBM and Hotspot temperature below 68-72C.

This is the difference if using v7
[2018-10-23 10:40:35] Pool rejected result 0x000036FE (low difficulty share)
[2018-10-23 10:40:39] GPU0 :    1740 H/s [T: 58c, RPM: 3698, CC: 1200 MHz, MC: 900 MHz][BUS:21]
[2018-10-23 10:40:39] GPU1 :    1503 H/s [T: 63c, RPM: 3719, CC: 1050 MHz, MC: 800 MHz][BUS:18]
[2018-10-23 10:40:39] GPU2 :    1789 H/s [T: 59c, RPM: 3723, CC: 1202 MHz, MC: 900 MHz][BUS:24]
[2018-10-23 10:40:39] GPU3 :    1926 H/s [T: 62c, RPM: 3690, CC: 1350 MHz, MC: 950 MHz][BUS:15]
[2018-10-23 10:40:39] GPU4 :    2063 H/s [T: 57c, RPM: 3665, CC: 1350 MHz, MC: 1100 MHz][BUS:9]
[2018-10-23 10:40:39] Total:    9021 H/s

And before temp around 65-70 in hot days (at ver 7).

[Marvell2]

whats the point of dealing with all this instability and extra heat from cnv8 when its less profitable atm than even eth.

hash rate is pretty much back to where it was 500ghs WTF lol

[jazz1984]

Can someone help? When i start my miner at the very start my main GPU always crash.... i've change 2-3 different cards and the problem is still the same. Using 18.5.1 and 1803win edition. Anyone with same problem like me?

Try to use the integrated gpu on your mobo for main display.

If you havent integrated gpu try to decrease intencity on main GPU for about 25-30% or until it became stable.

My 7970 (tahiti) 1000/1500  1.2v driver 18.5.2
{ "id" : 0, "intensity" : 58, "worksize" : 16, "threads" : 1} almost stable, just couple reboots for a night). Now decrease intecity by 1. And yes, monitor plugged in to this card too. Almost 460 H/s.

[Marvell2]

Code:

C:\Latest cast_xmr-vega-win64_120>switch-radeon-gpu -G 1 --largepages=on --hbcc=off autorestart
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  Switch Radeon GPU 0.9.5

  Restart GPUs and switch 'Compute Mode', 'Large Pages' and 'HBCC memory'
  on or off for example:
  'switch-radeon-gpu -G 0 --compute=on restart'

  Run with --help to list available optionss

  Coded by [glph3k] for more info visit http://www.gandalph3000.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Detected OpenCL Platform: OpenCL 2.1 AMD-APP (2580.6)

GPU1: Radeon Vega Frontier Edition (gfx901) ... no changes.

GPU1: Radeon Vega Frontier Edition (gfx901) | HBCC: OFF | Large Pages:  ON

C:\Latest cast_xmr-vega-win64_120>switch-radeon-gpu -G 1 --largepages=on --hbcc=off autorestart

still no good hash rate on FE with large pages on and HBCC off , using may 5.2 driver

Code:

2018-10-22 22:28:07] GPU0 :    1856 H/s [T: 55c, RPM: 2004, CC: 1474 MHz, MC: 920 MHz][BUS:20]
[2018-10-22 22:28:07] GPU1 :    1385 H/s [T: 55c, RPM: 4811, CC: 1408 MHz, MC: 1100 MHz][BUS:11]
[2018-10-22 22:28:07] GPU2 :    1933 H/s [T: 40c, RPM: 3887, CC: 1408 MHz, MC: 1100 MHz][BUS:8]
[2018-10-22 22:28:07] GPU3 :    1933 H/s [T: 42c, RPM: 4316, CC: 1408 MHz, MC: 1100 MHz][BUS:5]
[2018-10-22 22:28:07] GPU4 :    1832 H/s [T: 40c, RPM: 3033, CC: 1407 MHz, MC: 900 MHz][BUS:14]
[2018-10-22 22:28:07] GPU5 :    1350 H/s [T: 53c, RPM: 4803, CC: 1408 MHz, MC: 1100 MHz][BUS:17]
[2018-10-22 22:28:07] Total:    10289 H/s
[2018-10-22 22:28:07] Pool accepted result 0x000189B9
[2018-10-22 22:28:08] Pool accepted result 0x00004A03

se below 1350 max hash on both FEs , so damn anoying

[Mashy81]

1 rig  4 x vega56 + 2 x rx570   9400hs  1040watts at the wall

All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each

which setting do you have for your rx570 and biosmod?

1180 core  860mv  and 1950 memory 890mv.
Custom memory strap

[gerixusyu]

1 rig  4 x vega56 + 2 x rx570   9400hs  1040watts at the wall

All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each

which setting do you have for your rx570 and biosmod?

1180 core  860mv  and 1950 memory 890mv.
Custom memory strap

For which card is these clocks, can you post your straps for RX550 ?

[playfast]

whats the point of dealing with all this instability and extra heat from cnv8 when its less profitable atm than even eth.

hash rate is pretty much back to where it was 500ghs WTF lol

Not happy with it either, XMR difficulty drop ending in a blink
Knocked off ASICs but it seems the difficulty drop attracted too many GPU farms to move away from ETH.

[KhorneFlake]

Meh. I installed the older 18.5.1 driver, and it still doesn't help. It started promising with the secondary GPU spitting over 1200h/s, but the next report shows around 700 again… I could already see its gonna be a problem when in GPU-Z power consumption jumps between 60-140W, instead of being constant.

[playfast]

Meh. I installed the older 18.5.1 driver, and it still doesn't help. It started promising with the secondary GPU spitting over 1200h/s, but the next report shows around 700 again… I could already see its gonna be a problem when in GPU-Z power consumption jumps between 60-140W, instead of being constant.

Big power and hashrate fluctuations are usually caused by too high intensity or too low power limit setting.

[mey3R]

Adrenalin 18.6.1, Windows 10 1803, 5xRX580 3xRX480

I'm currently stuck at "Initializing OpenCL devices, please wait.. ..." as long as I got my iGPU enabled, once I turn it off it works right away but I would prefer to keep it enabled.

Is there any way to fix this? Tried "--cgpuid 2,3,4....." with the correct bus id numbers and ignoring the iGPU but that also doesn't help

[ntshb]

SRBMiner-CN.exe --config Config\config-normalv8.txt --pools pools.txt --enableduplicategpuid --logfile LOGTIME.txt




"gpu_conf" :
[
   { "id" : 0, "intensity" : 124, "worksize" : 16, "threads" : 2, "persistent_memory" : false},
{ "id" : 1, "intensity" : 124, "worksize" : 16, "threads" : 2, "persistent_memory" : false},
],
}


1222/1100 mhz

why is it that my hashrate for vegaFE is still 19xx?

[tanatana]

RX 470 4GB memory Hynix
1250@1900@1031 mV driver 18.6.1 Adrenalin mod bios
speed (700 - 720) h/s

"gpu_conf" :
[
   { "id" : 0, "intensity" : 64, "worksize" : 8, "threads" : 1}

],
}

https://i.imgur.com/xYCW8SK.png

[tvukoman]

Doktore after 12 to 24 hours mining V8 algo, Miner just ends (program closed) without noted error in log file.

I want to try disable gpu watchdog and use "reboot_script_gpu_watchdog" to try restart miner (not reboot rig). "reboot_script_gpu_watchdog" : filename to a batch file in miner directory, if set it turns off built in miner reset procedure on gpu failure, and instead runs this script

Is this possible and where i can find working example of script for restarting srbminer?

Txs!
 

[Int3ll]

Adrenalin 18.6.1, Windows 10 1803, 5xRX580 3xRX480

I'm currently stuck at "Initializing OpenCL devices, please wait.. ..." as long as I got my iGPU enabled, once I turn it off it works right away but I would prefer to keep it enabled.

Is there any way to fix this? Tried "--cgpuid 2,3,4....." with the correct bus id numbers and ignoring the iGPU but that also doesn't help

I have the same problem, WIN 10, 1803 but with 7X 550, sistem stops at Initializing OpenCL devices, please wait... or heating up sistem....

Is this related to WIN 10 build 1803??? 

had 1709 before and worked perfectly on v7 with uptime for over a month  .... but i updated to v8 and also updated WIN in the process...

[Mashy81]

1 rig  4 x vega56 + 2 x rx570   9400hs  1040watts at the wall

All my rx 570s hashing exactly same on v8 940hs.
My rx 550s are at 450hs each

how do you reach 450 with rx 550? what do you have in the config?

I don't buy it either. My best 560's max out at ~465 h/s.
I doubt the average 550 can do anything over 430 h/s, if it's real he must have crazy high mem oc and super aggressive timing straps.

No nothing crazy.
  rx 550 2gb cards. 1180 core.and 1950-1980 memory both 880mv.
Custom memory strap

[Mashy81]

i need vega 64 and vega 56 ppt regedit files. can someone help me?

You could search google quicker than it took to post that

[Bojcha]

is this ok to have stale share like this?

-------------------------STATS-------------------------

Miner version:  1.6.8
Driver version: 24.20.11021.1000
Mining time:    1 days, 15 hours, 44 minutes, 39 seconds

Algo: normalv8

Pool: asia.cryptonight-hub.miningpoolhub.com:20580
Connected since: 2018-10-21 18:00:25
Pool Difficulty: 60020
Pool latency: ~174 ms
Last job received: 26 seconds ago


Accepted(Stale)/Total shares: 7819(587)/7819 (100.0%)
Average time to find share: 18 seconds
1 min. average speed:   2771 H/s
5 min. average speed:   2768 H/s
30 min. average speed:  2770 H/s
Max. speed:             2781 H/s

Always choose pool with minimal latency. Everything over 90~100ms will make stale shares. Also does not mean that you will not have stales at 30ms, but it'll be far less.

[Marvell2]

SRBMiner-CN.exe --config Config\config-normalv8.txt --pools pools.txt --enableduplicategpuid --logfile LOGTIME.txt




"gpu_conf" :
[
   { "id" : 0, "intensity" : 124, "worksize" : 16, "threads" : 2, "persistent_memory" : false},
{ "id" : 1, "intensity" : 124, "worksize" : 16, "threads" : 2, "persistent_memory" : false},
],
}


1222/1100 mhz

why is it that my hashrate for vegaFE is still 19xx?

shit id be happy with 19xx for my FE

[Sapica]

Hi,

I've just checked stats and found some errors:

Miner version:  1.6.8
Driver version: 24.20.11021.1000
Mining time:    0 days, 0 hours, 13 minutes, 16 seconds

Algo: normalv8

Pool: xmr-eu1.nanopool.org:14444
Connected since: 2018-10-23 22:57:11
Pool Difficulty: 120001
Pool latency: ~110 ms
Last job received: 59 seconds ago


Accepted(Stale)/Total shares: 17(0)/17 (100.0%)
Average time to find share: 46 seconds
1 min. average speed:   3621 H/s
5 min. average speed:   3623 H/s
30 min. average speed:  0 H/s
Max. speed:             3657 H/s

Compute Errors:
BUS_ID_3: 5


Does anyone knows what mean ? :
Compute Errors:
BUS_ID_3: 5



Miner shows correct speed on that card:
[2018-10-23 23:16:12] Pool sent a new job (ID: 4817)
[2018-10-23 23:16:15] Pool accepted result 0x00000F78
[2018-10-23 23:16:16] Pool accepted result 0x0000477F
[2018-10-23 23:16:28] Pool accepted result 0x00000A8B
[2018-10-23 23:16:29] Pool accepted result 0x00003BA6
[2018-10-23 23:16:32] Pool sent a new job (ID: 4818)
[2018-10-23 23:17:12] GPU0 :    831 H/s [T: 69c, RPM: 1326, CC: 1120 MHz, MC: 1850 MHz][BUS:4]
[2018-10-23 23:17:12] GPU1 :    890 H/s [T: 51c, RPM: 1223, CC: 1150 MHz, MC: 2000 MHz][BUS:1]
[2018-10-23 23:17:12] GPU2 :    949 H/s [T: 57c, RPM: 1155, CC: 1200 MHz, MC: 2000 MHz][BUS:3]
[2018-10-23 23:17:12] GPU3 :    953 H/s [T: 59c, RPM: 1178, CC: 1200 MHz, MC: 2000 MHz][BUS:2]
[2018-10-23 23:17:12] Total:    3623 H/s
[2018-10-23 23:17:32] Pool sent a new job (ID: 4819)