molitar
|
 |
April 23, 2016, 02:34:54 PM |
|
over 4 hours and Decred is...
Confirmed: 0.0000 DCR Unconfirmed: 0.0661 DCR
I do not even have a single confirmed after that many hours! Decred needs 256 confirmations to mature. The average blockrate is 1 block per 5 min. So you should expect confirmed coins after 256 * 5 min = 21 h 20 min. 4h not enough. Thanks for that information but also how about the high number of rejects? Also I am getting this error many times. Pool returned error #56. DCR: Failed to connect to pool, retry in 20 sec... BTW -tt 100% does not work at all I tried it and watched my manual set fans in the Radeon settings drop down to 25% fan speed. It lowered instead of raising fan speed. I had to remove the -tt completely from the line and just use the AMD setting. Last question is my hash rates good for this mining? ETH: 04/23/16-10:37:55 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 41.149 Mh/s, Total Shares: 2, Rejected: 0, Time: 00:06 ETH: GPU0 21.065 Mh/s, GPU1 20.084 Mh/s DCR - Total Speed: 617.230 Mh/s, Total Shares: 6, Rejected: 2 DCR: GPU0 315.969 Mh/s, GPU1 301.261 Mh/s DCR: 04/23/16-10:38:47 - SHARE FOUND - (GPU 1) DCR: Share accepted! DCR: 04/23/16-10:38:59 - SHARE FOUND - (GPU 1) DCR: Share accepted! actually seem to be doing a bit better since I dropped in AMD settings the power level -20% on the R9 380x and same for the 280x. Is it possible to drop power requirements more on the 280x ok? That one card has option down to -50%.
|
|
|
|
|
|
|
|
|
"If you don't want people to know you're a scumbag then don't be a scumbag." -- margaritahuyan
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
dominuspro
|
 |
April 23, 2016, 02:36:21 PM |
|
Nobody has answered with my problems with this dual miner. I am getting horrible rates with Decred. 4GB XFX DD Black Edition 380x 3GB Sapphire Vapor-X 280x EthDcrMiner64.exe -epool coinotron.com:3344 -ewal molitar.miner1 -esm 2 -epsw <password> -dpool http://dcr.suprnova.cc:9112 -dwal molitar.miner1 -dpsw <password> -allpools 1 I'll add the -tt switch. But why am I getting all rejects? over 4 hours and Decred is... Confirmed: 0.0000 DCR Unconfirmed: 0.0661 DCR I do not even have a single confirmed after that many hours! ETH: 04/23/16-10:01:12 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 41.709 Mh/s, Total Shares: 206, Rejected: 4, Time: 06:05 ETH: GPU0 21.060 Mh/s, GPU1 20.650 Mh/s DCR - Total Speed: 625.638 Mh/s, Total Shares: 395, Rejected: 109 DCR: GPU0 315.896 Mh/s, GPU1 309.742 Mh/s ETH: 04/23/16-10:01:21 - SHARE FOUND - (GPU 0) ETH: Share accepted (156 ms)! ETH: 04/23/16-10:01:36 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.470 Mh/s, Total Shares: 207, Rejected: 4, Time: 06:05 ETH: GPU0 21.058 Mh/s, GPU1 19.412 Mh/s DCR - Total Speed: 607.043 Mh/s, Total Shares: 395, Rejected: 109 DCR: GPU0 315.864 Mh/s, GPU1 291.179 Mh/s ETH: 04/23/16-10:02:02 - SHARE FOUND - (GPU 1) ETH: Share accepted (218 ms)! ETH: 04/23/16-10:02:15 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 41.645 Mh/s, Total Shares: 208, Rejected: 4, Time: 06:06 ETH: GPU0 21.047 Mh/s, GPU1 20.598 Mh/s DCR - Total Speed: 624.676 Mh/s, Total Shares: 395, Rejected: 109 DCR: GPU0 315.712 Mh/s, GPU1 308.964 Mh/s ETH: 04/23/16-10:02:24 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.710 Mh/s, Total Shares: 208, Rejected: 4, Time: 06:06 ETH: GPU0 21.056 Mh/s, GPU1 19.654 Mh/s DCR - Total Speed: 610.646 Mh/s, Total Shares: 395, Rejected: 109 DCR: GPU0 315.842 Mh/s, GPU1 294.804 Mh/s ETH: 04/23/16-10:02:27 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 39.765 Mh/s, Total Shares: 208, Rejected: 4, Time: 06:06 ETH: GPU0 21.044 Mh/s, GPU1 18.721 Mh/s DCR - Total Speed: 596.475 Mh/s, Total Shares: 395, Rejected: 109 DCR: GPU0 315.659 Mh/s, GPU1 280.816 Mh/s ETH: 04/23/16-10:02:50 - New job (target 0x00000001310a5081) from coinotron.com:3344 Use stratum also for decred. Replace -dpool http://dcr.suprnova.cc:9112 with -dpool stratum+tcp://dcr.suprnova.cc:2252The rejects will drop to 1-3%  And You have to wait for almost 24h for DCR confirmation.
|
|
|
|
Trimegistus
Legendary
Offline
Activity: 1563
Merit: 1026
|
 |
April 23, 2016, 02:51:30 PM |
|
Use stratum also for decred. Replace -dpool http://dcr.suprnova.cc:9112 with -dpool stratum+tcp://dcr.suprnova.cc:2252The rejects will drop to 1-3%  And You have to wait for almost 24h for DCR confirmation. For me, the use of suprnova stratum for DCR, combined with -dcri 20 resulted in a rejection rate lower than 1% 
|
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
 |
April 23, 2016, 03:02:54 PM |
|
Currently I'm only mining Eth and want to test the dual mining feature.
What DCR pools exist where I don't need to signup?
Thanks
zpool.ca just provide BTC address Thanks!  password for DCR in zpool.ca will be "-psw c=BTC,decred"
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
ilia7777
Newbie
Offline
Activity: 39
Merit: 0
|
 |
April 23, 2016, 03:18:55 PM |
|
I used to mine with Ethos, now claymore seems to be available only on windows. Does anybody have any idea on how much RAM I need per card ? Most of my rigs are with 390s. The good thing about Ethos was that it was running fine with only 4Gb of RAM for a 6 card rig and not even consuming all 4.
|
|
|
|
Trimegistus
Legendary
Offline
Activity: 1563
Merit: 1026
|
 |
April 23, 2016, 03:32:02 PM |
|
I used to mine with Ethos, now claymore seems to be available only on windows. Does anybody have any idea on how much RAM I need per card ? Most of my rigs are with 390s. The good thing about Ethos was that it was running fine with only 4Gb of RAM for a 6 card rig and not even consuming all 4.
To mine ETH you need a minimum 2 Gb RAM per card, otherwise the DAG won't load into the cards's memory
|
|
|
|
molitar
|
 |
April 23, 2016, 03:36:29 PM |
|
Use stratum also for decred. Replace -dpool http://dcr.suprnova.cc:9112 with -dpool stratum+tcp://dcr.suprnova.cc:2252The rejects will drop to 1-3%  And You have to wait for almost 24h for DCR confirmation. Thanks that made a difference btw can this Cannot parse JSON! be ignored? ETH: Stratum - Connected DCR: Stratum - Connected Need to check DAG file (epoch #46), starting... ETH: Authorized Cannot parse JSON! DCR: Authorized DAG file (epoch #46) is ok. Need to check next DAG file (epoch #47) in back Applying DAG epoch #46 for GPU #0 Create GPU buffer for GPU #0 Applying DAG epoch #46 for GPU #0 done Applying DAG epoch #46 for GPU #1 Create GPU buffer for GPU #1 Applying DAG epoch #46 for GPU #1 done DAG file (epoch #47) is ok.
|
|
|
|
cryptoc19
Newbie
Offline
Activity: 15
Merit: 0
|
 |
April 23, 2016, 03:38:49 PM |
|
Currently I'm only mining Eth and want to test the dual mining feature.
What DCR pools exist where I don't need to signup?
Thanks
zpool.ca just provide BTC address Thanks!  password for DCR in zpool.ca will be "-psw c=BTC,decred" what's you reject rate for DCR on this pool? and, could you please post your full command when you use this pool? I've been toying around with it, but can't seem to get it working..
|
|
|
|
un4given
|
 |
April 23, 2016, 03:42:00 PM |
|
Running claymore's miner (eth only) for 55 hours straight with 0 eth rejects. Loving this miner. i am getting rejects all the time ;( i did delete DAG 2 times already but i am still getting rejects. any1 an idea why? using following command EthDcrMiner64.exe -epool eu1.ethermine.org:4444 -esm 1 -ewal 0xCcB701a1F4axxxxxxxxxxxxxxxxxxxxxxxxxxxxx.rig2 -epsw x also tried us1 adress for stratum, but no changes Use stratum - also tried us1 adress for stratum, but no changes. <- didnt see that part when i the miner was updated to allow dcr stratum that solved my dcr rejected shares.. :\ maybe try another pool? Yeah i need try to use smile pools without stratum. But stratum should work too. Using the last version of claymore
|
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
 |
April 23, 2016, 03:48:14 PM |
|
Currently I'm only mining Eth and want to test the dual mining feature.
What DCR pools exist where I don't need to signup?
Thanks
zpool.ca just provide BTC address Thanks!  password for DCR in zpool.ca will be "-psw c=BTC,decred" what's you reject rate for DCR on this pool? and, could you please post your full command when you use this pool? I've been toying around with it, but can't seem to get it working.. DCR rejects 1-2% at this pool. setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100 EthDcrMiner64.exe -epool asia1.ethpool.org:3333 -ewal <<ETH Address.workername>> -epsw x -dpool stratum+tcp://mine.zpool.ca:5744 -dwal <<BTC Address>> -dpsw c=BTC,decred
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
cryptoc19
Newbie
Offline
Activity: 15
Merit: 0
|
 |
April 23, 2016, 03:57:56 PM |
|
DCR rejects 1-2% at this pool.
setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_SINGLE_ALLOC_PERCENT 100
EthDcrMiner64.exe -epool asia1.ethpool.org:3333 -ewal <<ETH Address.workername>> -epsw x -dpool stratum+tcp://mine.zpool.ca:5744 -dwal <<BTC Address>> -dpsw c=BTC,decred
Thanks! 
|
|
|
|
kanoptx
Sr. Member
  
Offline
Activity: 406
Merit: 250
www.cryptocompare.com
|
 |
April 23, 2016, 04:03:23 PM |
|
I used to mine with Ethos, now claymore seems to be available only on windows. Does anybody have any idea on how much RAM I need per card ? Most of my rigs are with 390s. The good thing about Ethos was that it was running fine with only 4Gb of RAM for a 6 card rig and not even consuming all 4.
To mine ETH you need a minimum 2 Gb RAM per card, otherwise the DAG won't load into the cards's memory so, my fifth card wont work with 8gb of ram?! sh  , i did not know that...
|
|
|
|
restless
Legendary
Offline
Activity: 1151
Merit: 1001
|
 |
April 23, 2016, 04:24:49 PM |
|
Of course not, just make your virtual memory 8 to 16GB min and it will work.
|
|
|
|
klondike_bar
Legendary
Offline
Activity: 2030
Merit: 1003
ASIC Wannabe
|
 |
April 23, 2016, 04:46:19 PM |
|
I used to mine with Ethos, now claymore seems to be available only on windows. Does anybody have any idea on how much RAM I need per card ? Most of my rigs are with 390s. The good thing about Ethos was that it was running fine with only 4Gb of RAM for a 6 card rig and not even consuming all 4.
To mine ETH you need a minimum 2 Gb RAM per card, otherwise the DAG won't load into the cards's memory so, my fifth card wont work with 8gb of ram?! sh  , i did not know that... unless this software is different, thats false. etereum needs as much system ram as it needs GPU ram, because the DAG is loaded on both. But it only needs one copy in the ram for every running instance (and the DAG is only ~1.4GB, so even 5 seperate ethminer instances would be ~7.1GB of RAM usage) if you have all your cards running in te same instance of ethminer your RAM usage will only be 1.4Gb (size of the DAG)
|
|
|
|
kanoptx
Sr. Member
  
Offline
Activity: 406
Merit: 250
www.cryptocompare.com
|
 |
April 23, 2016, 04:51:50 PM |
|
okay, thought i had something else to worry about. i have always heard ram didnt matter much but since this miner is diff from most, that post got me wondering. thx  (still having freezes with my r9 290, i think that setting a FIXED value for gpu clock (factory) will fix it, can anyone give an opinion on this? I have fixed BSOD forcing constant voltage and got the temp down to 86-87 with 100% fan. which i may reduce to 70% depending on the temp.. I am running a test with the other 3 cards r9 280x to see if it may be something else)
|
|
|
|
arielbit
Legendary
Offline
Activity: 3248
Merit: 1056
|
 |
April 23, 2016, 05:10:18 PM |
|
I used to mine with Ethos, now claymore seems to be available only on windows. Does anybody have any idea on how much RAM I need per card ? Most of my rigs are with 390s. The good thing about Ethos was that it was running fine with only 4Gb of RAM for a 6 card rig and not even consuming all 4.
To mine ETH you need a minimum 2 Gb RAM per card, otherwise the DAG won't load into the cards's memory so, my fifth card wont work with 8gb of ram?! sh  , i did not know that... unless this software is different, thats false. etereum needs as much system ram as it needs GPU ram, because the DAG is loaded on both. But it only needs one copy in the ram for every running instance (and the DAG is only ~1.4GB, so even 5 seperate ethminer instances would be ~7.1GB of RAM usage) if you have all your cards running in te same instance of ethminer your RAM usage will only be 1.4Gb (size of the DAG) on windows 7 64bit you need system ram of 4gb, my rig with 2gb and 3gb can't mine until i upgraded it to 4gb..using ethminer haven't tried system ram downgrade with this dual miner yet..
|
|
|
|
knobson
|
 |
April 23, 2016, 06:04:48 PM |
|
!!! WARNING !!! You seem to be sending a large amount of INVALID shares ! Check your rigs, you might be mining the wrong algo and your hashrate could be displayed wrong! !!! WARNING !!!
DCR - Total Speed: 205.617 Mh/s, Total Shares: 5451, Rejected: 2075 DCR: GPU0 205.617 Mh/s DCR: Submitted share rejected! DCR: 04/23/16-21:03:38 - SHARE FOUND - (GPU 0) DCR: Submitted share rejected! DCR: 04/23/16-21:03:39 - SHARE FOUND - (GPU 0) DCR: Submitted share rejected! Pool returned error #56. DCR: Failed to check work on pool, retry in 20 sec...
|
|
|
|
molitar
|
 |
April 23, 2016, 06:16:52 PM |
|
ETH: 04/23/16-14:12:04 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.911 Mh/s, Total Shares: 109, Rejected: 0, Time: 02:37 ETH: GPU0 21.052 Mh/s, GPU1 19.859 Mh/s DCR - Total Speed: 613.668 Mh/s, Total Shares: 1334, Rejected: 11 DCR: GPU0 315.781 Mh/s, GPU1 297.887 Mh/s DCR: 04/23/16-14:12:11 - New job (target 0x00000000ffff0000, block #21943) from dcr.suprnova.cc:2252 ETH: 04/23/16-14:12:18 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 41.391 Mh/s, Total Shares: 109, Rejected: 0, Time: 02:38 ETH: GPU0 21.066 Mh/s, GPU1 20.325 Mh/s DCR - Total Speed: 620.868 Mh/s, Total Shares: 1334, Rejected: 11 DCR: GPU0 315.996 Mh/s, GPU1 304.872 Mh/s DCR: 04/23/16-14:12:19 - SHARE FOUND - (GPU 0) DCR: Share accepted (109 ms)! Seemed to be doing pretty good now.. BTW I get this intermittently. ETH: 04/23/16-14:14:24 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.910 Mh/s, Total Shares: 110, Rejected: 0, Time: 02:40 ETH: GPU0 21.062 Mh/s, GPU1 19.848 Mh/s DCR - Total Speed: 613.646 Mh/s, Total Shares: 1343, Rejected: 11 DCR: GPU0 315.924 Mh/s, GPU1 297.722 Mh/s DCR: 04/23/16-14:14:25 - SHARE FOUND - (GPU 0) DCR: 04/23/16-14:14:36 - SHARE FOUND - (GPU 1) DCR: Stratum - socket send failed 10053, disconnect DCR: 04/23/16-14:14:40 - SHARE FOUND - (GPU 1) DCR: Stratum - socket send failed 10038, disconnect DCR: Stratum - connecting to 'dcr.suprnova.cc' <178.33.228.14> port 2252 DCR: Stratum - Connected DCR: Authorized right after this disconnect is when I will get 2 or 3 rejects at least.. How can I resolve this disconnect issue?
|
|
|
|
McNulty
|
 |
April 23, 2016, 06:44:56 PM |
|
ETH: 04/23/16-14:12:04 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.911 Mh/s, Total Shares: 109, Rejected: 0, Time: 02:37 ETH: GPU0 21.052 Mh/s, GPU1 19.859 Mh/s DCR - Total Speed: 613.668 Mh/s, Total Shares: 1334, Rejected: 11 DCR: GPU0 315.781 Mh/s, GPU1 297.887 Mh/s DCR: 04/23/16-14:12:11 - New job (target 0x00000000ffff0000, block #21943) from dcr.suprnova.cc:2252 ETH: 04/23/16-14:12:18 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 41.391 Mh/s, Total Shares: 109, Rejected: 0, Time: 02:38 ETH: GPU0 21.066 Mh/s, GPU1 20.325 Mh/s DCR - Total Speed: 620.868 Mh/s, Total Shares: 1334, Rejected: 11 DCR: GPU0 315.996 Mh/s, GPU1 304.872 Mh/s DCR: 04/23/16-14:12:19 - SHARE FOUND - (GPU 0) DCR: Share accepted (109 ms)! Seemed to be doing pretty good now.. BTW I get this intermittently. ETH: 04/23/16-14:14:24 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 40.910 Mh/s, Total Shares: 110, Rejected: 0, Time: 02:40 ETH: GPU0 21.062 Mh/s, GPU1 19.848 Mh/s DCR - Total Speed: 613.646 Mh/s, Total Shares: 1343, Rejected: 11 DCR: GPU0 315.924 Mh/s, GPU1 297.722 Mh/s DCR: 04/23/16-14:14:25 - SHARE FOUND - (GPU 0) DCR: 04/23/16-14:14:36 - SHARE FOUND - (GPU 1) DCR: Stratum - socket send failed 10053, disconnect DCR: 04/23/16-14:14:40 - SHARE FOUND - (GPU 1) DCR: Stratum - socket send failed 10038, disconnect DCR: Stratum - connecting to 'dcr.suprnova.cc' <178.33.228.14> port 2252 DCR: Stratum - Connected DCR: Authorized right after this disconnect is when I will get 2 or 3 rejects at least.. How can I resolve this disconnect issue? do you have an Asus Router ? if yes, try without "AiProtection"
|
|
|
|
molitar
|
 |
April 23, 2016, 07:09:57 PM |
|
No it's Actiontech as I have FIOS now Frontier 80/80MB connection. Ok I found I needed to lower my intensity on my main gpu for my system. -ethi 16,4 My 4GB 380x is my primary card and my 3GB 280x is my secondary but ethminer sees it the opposite direction. So lowering intensity to 4 reduced lag in my Windows and that lowered disconnects down quite a bit. But still having a few just not as many now. It hasn't effected the performance much either. ETH: 04/23/16-15:04:43 - New job (target 0x00000001310a5081) from coinotron.com:3344 ETH - Total Speed: 37.289 Mh/s, Total Shares: 26, Rejected: 0, Time: 00:39 ETH: GPU0 21.067 Mh/s, GPU1 16.222 Mh/s DCR - Total Speed: 559.327 Mh/s, Total Shares: 292, Rejected: 0 DCR: GPU0 316.004 Mh/s, GPU1 243.323 Mh/s DCR: 04/23/16-15:04:46 - SHARE FOUND - (GPU 0) DCR: 04/23/16-15:04:46 - SHARE FOUND - (GPU 0) DCR: 04/23/16-15:04:46 - SHARE FOUND - (GPU 1) DCR: 04/23/16-15:04:48 - SHARE FOUND - (GPU 0) DCR: Share accepted (1966 ms)! DCR: Share accepted (1966 ms)! DCR: Share accepted (1966 ms)! DCR: Share accepted (1966 ms)! DCR: 04/23/16-15:04:51 - SHARE FOUND - (GPU 1) DCR: Share accepted (514 ms)! DCR: 04/23/16-15:05:01 - SHARE FOUND - (GPU 0) DCR: Share accepted (125 ms)! ETH: 04/23/16-15:05:10 - New job (target 0x00000001310a5081) from coinotron.com:3344 Now to the other I have this PC as a DMZ host with mininum security. I rely on PC firewall for any real threats. The only other thing I have is inbound packets scanning ports are dropped on the main ports that are scanned. RPC - TCP Any -> 135 Net_BIOS - TCP Any -> 139 HTTPS - TCP Any -> 443 MSFT_DS - TCP Any -> 445 SSH - TCP Any -> 22 and block ip fragments. So that should not affect anything. Response time on many test sites are 51-52 ms for latency.
|
|
|
|
|