OFFICIAL CGMINER mining software thread for linux/win/osx/mips/arm/r-pi 4.11.1

[mdude77]

Why would you run 12.8 when 13.4 works perfectly fine? Were 7000 cards even out when 12.8 was released? Did you ever consider that you are using drivers that were never intended for that card? Have you also considered that it is why they have released newer drivers? To fix issues?

Actually 7xxx cards are supported since 11.12 (8.921) drivers.
Also AMD interest is in fixing gaming issues.

A newer driver could be better at gaming, but not necessarily at mining.
In fact, older drivers = better drivers.

Maybe try Linux? It's so easy.

Um.. your mileage may vary.  I spent a day trying to get linux to do what I can do in windows in an hour, and gave up.

M

[kosmokramer]

Windows 7 x64 - using Zadig drivers - 1x Block Erupter (sapphire) - USB 3.0 Anker 10 port hub

command:

Code:

cgminer-nogpu -o stratum.btcguild.com:3333 -u kosmokramer_ERUPTER -p [x] --icarus-options 115200:1:1 --icarus-timing 3.0=100

3.2.1 opens and runs for a couple seconds reporting that device detected, then undetected, then detected, then undetected, ....
then crashes - I believe this is the "zombified" error reported a couple posts above me.

I assume this is the 3.0 support that you say is pending.

I, for one, would be happy to donate if you could push through 3.0 support - I'd love to use this software!!

I test every one of these for customers prior to shipment (currently using BitMinter but would like to use cgminer too), and it would be very valuable to me if cgminer worked with my setup. I sometimes have 50+ plugged into Anker 3.0 hubs when new inventory arrives and it's just not handling that at present.

[mufa23]

This may, or may have been asked a million times. I'm fairly new to CGminer, and wanted to use it on my gaming PC. Is there an option that allows more gpu power to graphics demanding things (games, videos, etc.), then when I stop, cgminer would dedicate more processing power to itself and mine faster.

In other words, I used to use GUIminer (poclbm) for my gaming PC since I could use the "-f" flag to always make sure I had a certain FPS. Mining speed would be slow while playing games, but automatically resume once I was done and/or afk.

[os2sam]

This may, or may have been asked a million times. I'm fairly new to CGminer, and wanted to use it on my gaming PC. Is there an option that allows more gpu power to graphics demanding things (games, videos, etc.), then when I stop, cgminer would dedicate more processing power to itself and mine faster.

In other words, I used to use GUIminer (poclbm) for my gaming PC since I could use the "-f" flag to always make sure I had a certain FPS. Mining speed would be slow while playing games, but automatically resume once I was done and/or afk.

Dynamic Intensity

-I d

From top post

--intensity|-I <arg> Intensity of GPU scanning (d or -10 -> 10, default: d to maintain desktop interactivity)

[Lucko]

You sure you have the opencl sdk?

My machine is also my workstation, and I need Windows.  It worked before on Win7 - it's why it now doesn't that's making my mind boggle. 

Surely if I didn't have the SDK, it wouldn't run at all?  I've never needed to install anything other than the drivers in the past. 

It runs for a few minutes at high CPU, then the machine locks up solid.  Yet it'll run Furmark for hours with no issues...

I'm going to blow this 7 install away and stick 8 on, see if that helps. 

This is what I do. Not sure if this is something recommended but it works. I have a test computer(same cgminer) and I create .bin file. Looking for best driver SDK combination... Then I move cart to miner install drivers and copy .bin. It works for me. So copy .bin from the old to new one...

Uptime is everything...

[dwolfman]

This may, or may have been asked a million times. I'm fairly new to CGminer, and wanted to use it on my gaming PC. Is there an option that allows more gpu power to graphics demanding things (games, videos, etc.), then when I stop, cgminer would dedicate more processing power to itself and mine faster.

In other words, I used to use GUIminer (poclbm) for my gaming PC since I could use the "-f" flag to always make sure I had a certain FPS. Mining speed would be slow while playing games, but automatically resume once I was done and/or afk.

Dynamic Intensity

-I d

From top post

--intensity|-I <arg> Intensity of GPU scanning (d or -10 -> 10, default: d to maintain desktop interactivity)

While I use this in my setup, I also use Bitcoin Miners In Tray to take care of switching things around when I need them.

For example, I've maximized my hashrate with dynamic intensity such that it doesn't interfere with desktop usage, but it slows down everything and causes games to stutter a lot if the miner is still running while I'm playing a game.  So I have Bitcoin Miners In Tray set to shut down cgminer completely whenever certain programs are running.  Since I have Steam on my system, I have it set to look for GameOverlayUI.exe in the running processes.  It automatically shuts down cgminer when I start anything from inside Steam (for the most part) and restarts cgminer a few seconds after I exit the game.  Works beautifully!

Note it can do much more than just what I'm doing with it.  Read up on Bitcoin Miners In Tray in this thread: https://bitcointalk.org/index.php?topic=149442.0

[Zanatos666]

Question ... ?
Is anyone having problems with cgminer 3.2.1 Icarus mining (Icarus, Lancelot or Erupter only) on anything OTHER than the RPi?
I seem to have narrowed it down to possibly being a timer bug (happening inside libusb - so possibly a kernel problem)
And if you are NOT having problems with 3.2.1 on RPi, could you tell me your kernel version?
with uname -a
Thanks!

Edit: and not using USB 3.0

Trying to catch up on posts, might have missed something on this, but is this/could this be the same issue that is causing Jalapeno's to not run on r-pi's?

[de_xt]

With cgminer 3.2.1 I get a BSOD when I close & restart cgminer 2 or 3 times during the same Windows session. Never happened with 3.1.0 .The BSOD occured while initializing cgminer (screen stops responding and then the Blue Screen of Death).

My setup is a Core2 Quad Q6600 with 2x5850 in Crossfire, and  Win 7 x64 with Catalyst 3.14 and the following config file:

Code:

{
"pools" : [
{
		"url" : "http://127.0.0.1:7956",
		"user" : "username",
		"pass" : "password"
	}
],

"scrypt" : true,
"intensity" : "18,17",
"gpu-fan" : "60,75",
"auto-fan" : true,
"queue" : "0",
"expiry" : "1",
"scan-time" : "1",
"thread-concurrency" : "6400",
"shaders" : "1440",
"worksize" : "256",
"gpu-threads" : "1",
"lookup-gap" : "2"
}

Hope you can fix this possible  bug. Thanks!

[-ck]

With cgminer 3.2.1 I get a BSOD when I close & restart cgminer 2 or 3 times during the same Windows session. Never happened with 3.1.0 .The BSOD occured while initializing cgminer (screen stops responding and then the Blue Screen of Death).

My setup is a Core2 Quad Q6600 with 2x5850 in Crossfire, and  Win 7 x64 with Catalyst 3.14 and the following config file:

Hope you can fix this possible  bug. Thanks!

A BSOD is an operating system bug. You expect us to fix windows?

[sLide.]

I'm experiencing a issue with CGminer.

I recently moved my XFX 6870 from my gaming machine which was used to mine when I wasn't gaming to my first rig.  I keep getting error's from windows saying it had to stop the program from running.

MoBo: msi x58A-GD45
Proc: I7 920
Memory : 2GB
Video Card: 6870 XFX HD - CCC Version - 13.4 Direct3D Version 9.14.10.0969

Not entirely sure what the problem could be.  I've tried running as admin.  Any help?  Thanks!

I had same problem with incompatible OpenCL driver combination... Changing it might help

In event log, I'm getting this error -

- System

  - Provider

   [ Name]  Application Error
 
  - EventID 1000

   [ Qualifiers]  0
 
   Level 2
 
   Task 100
 
   Keywords 0x80000000000000
 
  - TimeCreated

   [ SystemTime]  2013-06-07T14:03:10.000000000Z
 
   EventRecordID 1752
 
   Channel Application
 
   Computer Miner1-PC
 
   Security
 

- EventData

   cgminer.exe
   0.0.0.0
   518e20db
   cgminer.exe
   0.0.0.0
   518e20db
   c0000005
   000265be
   12a0
   01ce6387bbccda57
   C:\Users\Miner1\Desktop\cgminer\cgminer-3.1.1-windows\cgminer.exe
   C:\Users\Miner1\Desktop\cgminer\cgminer-3.1.1-windows\cgminer.exe
   fc31de57-cf7a-11e2-8d68-6c626de9cc51

Any help on this.  Google is saying that some of these error's happen when the Proc trys to access "No-Mans Land" in the memory.  It's pretty much a dump spot.  Any advice?

Anyone have any direction with this?  Still need help.

[-ck]

I'm experiencing a issue with CGminer.

I recently moved my XFX 6870 from my gaming machine which was used to mine when I wasn't gaming to my first rig.  I keep getting error's from windows saying it had to stop the program from running.

MoBo: msi x58A-GD45
Proc: I7 920
Memory : 2GB
Video Card: 6870 XFX HD - CCC Version - 13.4 Direct3D Version 9.14.10.0969

Not entirely sure what the problem could be.  I've tried running as admin.  Any help?  Thanks!

I had same problem with incompatible OpenCL driver combination... Changing it might help

In event log, I'm getting this error -

- System

  - Provider

   [ Name]  Application Error
 
  - EventID 1000

   [ Qualifiers]  0
 
   Level 2
 
   Task 100
 
   Keywords 0x80000000000000
 
  - TimeCreated

   [ SystemTime]  2013-06-07T14:03:10.000000000Z
 
   EventRecordID 1752
 
   Channel Application
 
   Computer Miner1-PC
 
   Security
 

- EventData

   cgminer.exe
   0.0.0.0
   518e20db
   cgminer.exe
   0.0.0.0
   518e20db
   c0000005
   000265be
   12a0
   01ce6387bbccda57
   C:\Users\Miner1\Desktop\cgminer\cgminer-3.1.1-windows\cgminer.exe
   C:\Users\Miner1\Desktop\cgminer\cgminer-3.1.1-windows\cgminer.exe
   fc31de57-cf7a-11e2-8d68-6c626de9cc51

Any help on this.  Google is saying that some of these error's happen when the Proc trys to access "No-Mans Land" in the memory.  It's pretty much a dump spot.  Any advice?

Anyone have any direction with this?  Still need help.

Driver + SDK. Use a clean uninstaller and start again... as it says in the GPU README.

[kano]

Question ... ?
Is anyone having problems with cgminer 3.2.1 Icarus mining (Icarus, Lancelot or Erupter only) on anything OTHER than the RPi?
I seem to have narrowed it down to possibly being a timer bug (happening inside libusb - so possibly a kernel problem)
And if you are NOT having problems with 3.2.1 on RPi, could you tell me your kernel version?
with uname -a
Thanks!

Edit: and not using USB 3.0

Trying to catch up on posts, might have missed something on this, but is this/could this be the same issue that is causing Jalapeno's to not run on r-pi's?

My Jalapeno works fine on my RPi - but yes I'm using a USB2.0 powered hub.
Though, even plugging the USB2.0 hub in, with the Jalapeno and the AMU already plugged into it, crashes linux on the RPi ... before I even go near cgminer.

The RPi problem seems to only affect the Icarus driver, however, USB 3.0 is pretty much not working at the moment for anything
I do have a powered USB3.0 hub I bought recently for testing this, but have been side tracked:
I've been running around in circles with the AMU Icarus RPi problem only to find it may well be an OS bug ... I've finally tracked it down to a call into libusb that never comes back and never times out ... but it works perfectly on my desktop ...

Anyway will look into USB 3.0 soon.

[Zanatos666]

Question ... ?
Is anyone having problems with cgminer 3.2.1 Icarus mining (Icarus, Lancelot or Erupter only) on anything OTHER than the RPi?
I seem to have narrowed it down to possibly being a timer bug (happening inside libusb - so possibly a kernel problem)
And if you are NOT having problems with 3.2.1 on RPi, could you tell me your kernel version?
with uname -a
Thanks!

Edit: and not using USB 3.0

Trying to catch up on posts, might have missed something on this, but is this/could this be the same issue that is causing Jalapeno's to not run on r-pi's?

My Jalapeno works fine on my RPi - but yes I'm using a USB2.0 powered hub.
Though, even plugging the USB2.0 hub in, with the Jalapeno and the AMU already plugged into it, crashes linux on the RPi ... before I even go near cgminer.

The RPi problem seems to only affect the Icarus driver, however, USB 3.0 is pretty much not working at the moment for anything
I do have a powered USB3.0 hub I bought recently for testing this, but have been side tracked:
I've been running around in circles with the AMU Icarus RPi problem only to find it may well be an OS bug ... I've finally tracked it down to a call into libusb that never comes back and never times out ... but it works perfectly on my desktop ...

Anyway will look into USB 3.0 soon.

Okay, clearly I am missing something.  I have my Jalapeno plugged directly into my rpi.  Should I not be doing that in order to get cgminer to recognize it?  I am running it headless, just my rpi with my jalapeno plugged into it and using putty for anything, not using a keyboard.  So, maybe I missed something.  I have a USB 2.0 hub I could use if that for some reason solves the problem.

[-ck]

Okay, clearly I am missing something.  I have my Jalapeno plugged directly into my rpi.  Should I not be doing that in order to get cgminer to recognize it?  I am running it headless, just my rpi with my jalapeno plugged into it and using putty for anything, not using a keyboard.  So, maybe I missed something.  I have a USB 2.0 hub I could use if that for some reason solves the problem.

I don't have an rpi so can only offer generic advice, but I have seen many many reports saying the rpi usb ports are flaky and putting a reliable powered usb hub between the rpi and the devices fixes them, so it's worth a shot.

[kosmokramer]

Anyway will look into USB 3.0 soon.

Awesome!! Thanks so much for your hard work - you truly do amazing things for this community!!

[Naelr]

Question ... ?
Is anyone having problems with cgminer 3.2.1 Icarus mining (Icarus, Lancelot or Erupter only) on anything OTHER than the RPi?
I seem to have narrowed it down to possibly being a timer bug (happening inside libusb - so possibly a kernel problem)
And if you are NOT having problems with 3.2.1 on RPi, could you tell me your kernel version?
with uname -a
Thanks!

Edit: and not using USB 3.0

I am, I posted several pages back... tried 3.2.1 and your patched 3.2.1a it mines just fine but the block erupters keep going zombie... they come back but after about 1-2 hours 10 block erupters zombie out and fill up my console screen with zombies... they do get restarted and start mining again.. so it is good in that respect but the average hasrate for the box is lower then with 3.1.1 because they keep stopping but that is kind of a given isn't it ...

uname -a

Linux coiner 3.2.0-45-generic #70-Ubuntu SMP Wed May 29 20:12:06 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux

Ubuntu 12.04 LTS 64 bit... NO usb 3.0

I know you asked NOT having problems for the uname -a but hey wtf right!?

Naelr

[aSicPuppy]

Question ... ?
Is anyone having problems with cgminer 3.2.1 Icarus mining (Icarus, Lancelot or Erupter only) on anything OTHER than the RPi?
I seem to have narrowed it down to possibly being a timer bug (happening inside libusb - so possibly a kernel problem)
And if you are NOT having problems with 3.2.1 on RPi, could you tell me your kernel version?
with uname -a
Thanks!

Edit: and not using USB 3.0

Trying to catch up on posts, might have missed something on this, but is this/could this be the same issue that is causing Jalapeno's to not run on r-pi's?

My Jalapeno works fine on my RPi - but yes I'm using a USB2.0 powered hub.
Though, even plugging the USB2.0 hub in, with the Jalapeno and the AMU already plugged into it, crashes linux on the RPi ... before I even go near cgminer.

The RPi problem seems to only affect the Icarus driver, however, USB 3.0 is pretty much not working at the moment for anything
I do have a powered USB3.0 hub I bought recently for testing this, but have been side tracked:
I've been running around in circles with the AMU Icarus RPi problem only to find it may well be an OS bug ... I've finally tracked it down to a call into libusb that never comes back and never times out ... but it works perfectly on my desktop ...

Anyway will look into USB 3.0 soon.

Okay, clearly I am missing something.  I have my Jalapeno plugged directly into my rpi.  Should I not be doing that in order to get cgminer to recognize it?  I am running it headless, just my rpi with my jalapeno plugged into it and using putty for anything, not using a keyboard.  So, maybe I missed something.  I have a USB 2.0 hub I could use if that for some reason solves the problem.

https://bitcointalk.org/index.php?topic=28402.msg2409598#msg2409598

Try increasing the timeout and recompiling. Some jalepenos appear to be taking >850 ms to respond to the initial getinfo request in linux.

[-ck]

Okay, clearly I am missing something.  I have my Jalapeno plugged directly into my rpi.  Should I not be doing that in order to get cgminer to recognize it?  I am running it headless, just my rpi with my jalapeno plugged into it and using putty for anything, not using a keyboard.  So, maybe I missed something.  I have a USB 2.0 hub I could use if that for some reason solves the problem.

https://bitcointalk.org/index.php?topic=28402.msg2409598#msg2409598

Try increasing the timeout and recompiling. Some jalepenos appear to be taking >850 ms to respond to the initial getinfo request in linux.

There's a change that directly addresses this already in git master, so compiling from git master should do it.

[stormos]

There is a problem with 3.2.xx on GPU only machines running windows 7 and catalyst driver 13.4
CGMiner crashes at start
Oldest drivers or previous versions of cgminer work fine

Code:

 [2013-06-10 14:37:52] Started cgminer 3.2.1
 [2013-06-10 14:37:52] Loaded configuration file cgminer.conf
 [2013-06-10 14:37:52] RES: thread starting
 [2013-06-10 14:37:52] CL Platform 0 vendor: Advanced Micro Devices, Inc.
 [2013-06-10 14:37:52] CL Platform 0 name: AMD Accelerated Parallel Processing
 [2013-06-10 14:37:52] CL Platform 0 version: OpenCL 1.2 AMD-APP (1124.2)
 [2013-06-10 14:37:52] Platform 0 devices: 1
 [2013-06-10 14:37:52] 	0	Cypress
 [2013-06-10 14:37:52] GPU 0 iAdapterIndex 0 strUDID PCI_VEN_1002&DEV_689E&SUBSYS_E140174B&REV_00_4&EEFFDB8&0&0008A iBusNumber 1 iDeviceNumber 0 iFunctionNumber 0 iVendorID 1002 strAdapterName  ATI Radeon HD 5800 Series 
 [2013-06-10 14:37:53] GPU 0 ATI Radeon HD 5800 Series hardware monitoring enabled
 [2013-06-10 14:37:53] Setting GPU 0 engine clock to 973
 [2013-06-10 14:37:53] Setting GPU 0 memory clock to 600
 [2013-06-10 14:37:53] USB scan devices: checking for ICA devices
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 8086:1c2d instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 8086:1c26 instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 046d:c312 instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 046d:c52f instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 04b4:6560 instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 058f:6387 instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for ICA 067b:2303 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for AMU 10c4:ea60 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for BLT 0403:6001 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for LLT 0403:6001 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:8350 but found 8087:0024 instead
 [2013-06-10 14:37:53] ICA looking for CMR 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] USB scan devices: checking for BAS devices
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 8086:1c2d instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 8086:1c26 instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 046d:c312 instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 046d:c52f instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 04b4:6560 instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 058f:6387 instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] BAS looking for BAS 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] USB scan devices: checking for BFL devices
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 8086:1c2d instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 8086:1c26 instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 046d:c312 instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 046d:c52f instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 04b4:6560 instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 058f:6387 instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] BFL looking for BFL 0403:6014 but found 8087:0024 instead
 [2013-06-10 14:37:53] USB scan devices: checking for MMQ devices
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 8086:1c2d instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 8086:1c26 instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 046d:c312 instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 046d:c52f instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 04b4:6560 instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 058f:6387 instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 8087:0024 instead
 [2013-06-10 14:37:53] MMQ looking for MMQ 1fc9:0003 but found 8087:0024 instead
 [2013-06-10 14:37:53] Not a ZTEX device 8086:1c2d
 [2013-06-10 14:37:53] Not a ZTEX device 8086:1c26
 [2013-06-10 14:37:53] Not a ZTEX device 046d:c312
 [2013-06-10 14:37:53] Not a ZTEX device 046d:c52f
 [2013-06-10 14:37:53] Not a ZTEX device 04b4:6560
 [2013-06-10 14:37:53] Not a ZTEX device 058f:6387
 [2013-06-10 14:37:53] Not a ZTEX device 8087:0024
 [2013-06-10 14:37:53] Not a ZTEX device 8087:0024
 [2013-06-10 14:37:53] Probing for an alive pool
 [2013-06-10 14:37:53] Popping work to stage thread
 [2013-06-10 14:37:53] Testing pool http://mint.bitminter.com:8332
 [2013-06-10 14:37:53] Testing pool http://pool.50btc.com:8332
 [2013-06-10 14:37:53] Testing pool http://pool-ru.50btc.com:8332
 [2013-06-10 14:37:53] Testing pool http://mint.bitminter.com:8332
 [2013-06-10 14:37:53] Testing pool http://stratum.bitcoin.cz:3333
 [2013-06-10 14:37:53] Testing pool http://stratum.btcguild.com:3333
 [2013-06-10 14:37:53] Testing pool http://pit.deepbit.net:8332
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] Probing for GBT support
 [2013-06-10 14:37:53] No GBT coinbase + append support found, using getwork protocol
 [2013-06-10 14:37:53] No GBT coinbase + append support found, using getwork protocol
 [2013-06-10 14:37:53] Testing pool 1 stratum stratum+tcp://50btc.com:3333
 [2013-06-10 14:37:53] HTTP request failed: Empty reply from server
 [2013-06-10 14:37:53] No GBT coinbase + append support found, using getwork protocol
 [2013-06-10 14:37:54] Testing pool 2 stratum stratum+tcp://178.33.43.149:3333
 [2013-06-10 14:37:54] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:54] Switching pool 1 http://pool.50btc.com:8332 to stratum+tcp://50btc.com:3333
 [2013-06-10 14:37:54] HTTP request failed: Empty reply from server
 [2013-06-10 14:37:54] No GBT coinbase + append support found, using getwork protocol
 [2013-06-10 14:37:54] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:54] Switching pool 2 http://pool-ru.50btc.com:8332 to stratum+tcp://178.33.43.149:3333
 [2013-06-10 14:37:54] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:54] JSON-RPC call failed: {
   "code": -1,
   "message": "error"
}
 [2013-06-10 14:37:54] No GBT coinbase + append support found, using getwork protocol
 [2013-06-10 14:37:54] HTTP request failed: Empty reply from server
 [2013-06-10 14:37:54] HTTP request failed: Empty reply from server
 [2013-06-10 14:37:54] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:54] GBT coinbase + append support found, switching to GBT protocol
 [2013-06-10 14:37:54] GBT coinbase + append support found, switching to GBT protocol
 [2013-06-10 14:37:54] Stratum authorisation success for pool 1
 [2013-06-10 14:37:54] Switching to pool 1 http://pool.50btc.com:8332 - first alive pool
 [2013-06-10 14:37:54] Pool 1 http://pool.50btc.com:8332 alive
 [2013-06-10 14:37:54] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:54] Stratum authorisation success for pool 2
 [2013-06-10 14:37:55] Pool 2 http://pool-ru.50btc.com:8332 alive
 [2013-06-10 14:37:55] Pool 4 stratum session id: ae6812eb4cd7735a302a8a9dd95cf71f
 [2013-06-10 14:37:55] Successfully retrieved and deciphered work from pool 6 http://pit.deepbit.net:8332
 [2013-06-10 14:37:55] Pushing pooltest work to base pool
 [2013-06-10 14:37:55] Network diff set to 15.6M
 [2013-06-10 14:37:55] Pool 6 http://pit.deepbit.net:8332 alive
 [2013-06-10 14:37:55] New block: 000c3b869069aad9... diff 15.6M
 [2013-06-10 14:37:55] Pushing work to getwork queue
 [2013-06-10 14:37:55] Popping work to stage thread
 [2013-06-10 14:37:55] JSON-RPC decode failed: (unknown reason)
 [2013-06-10 14:37:55] Failed to resume stratum, trying afresh
 [2013-06-10 14:37:55] Testing pool 3 stratum stratum+tcp://eu1.bitminter.com:3333
 [2013-06-10 14:37:55] Pushing ping to thread 0
 [2013-06-10 14:37:55] Init GPU thread 0 GPU 0 virtual GPU 0
 [2013-06-10 14:37:55] CL Platform vendor: Advanced Micro Devices, Inc.
 [2013-06-10 14:37:55] JSON-RPC decode failed: (unknown reason)
 [2013-06-10 14:37:55] CL Platform name: AMD Accelerated Parallel Processing
 [2013-06-10 14:37:55] Failed to resume stratum, trying afresh
 [2013-06-10 14:37:55] CL Platform version: OpenCL 1.2 AMD-APP (1124.2)
 [2013-06-10 14:37:55] List of devices:
 [2013-06-10 14:37:55] 	0	Cypress
 [2013-06-10 14:37:55] Selected 0: Cypress
 [2013-06-10 14:37:55] Testing pool 0 stratum stratum+tcp://eu1.bitminter.com:3333
 [2013-06-10 14:37:55] Preferred vector width reported 4
 [2013-06-10 14:37:55] Max work group size reported 256
 [2013-06-10 14:37:55] Max mem alloc size is 536870912
 [2013-06-10 14:37:55] No binary found, generating from source
 [2013-06-10 14:37:55] Setting worksize to 128
 [2013-06-10 14:37:55] Patched source to suit 2 vectors
 [2013-06-10 14:37:55] cl_amd_media_ops found, setting BITALIGN
 [2013-06-10 14:37:55] BFI_INT patch requiring device found, patched source with BFI_INT
 [2013-06-10 14:37:55] CompilerOptions: -D WORKSIZE=128 -D VECTORS2 -D WORKVEC=256 -D BITALIGN -D BFI_INT
 [2013-06-10 14:37:55] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:55] Switching pool 3 http://mint.bitminter.com:8332 to stratum+tcp://eu1.bitminter.com:3333
 [2013-06-10 14:37:55] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:55] Switching pool 0 http://mint.bitminter.com:8332 to stratum+tcp://eu1.bitminter.com:3333
 [2013-06-10 14:37:55] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:55] Pool 5 difficulty set to 1.000000
 [2013-06-10 14:37:55] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:55] Pool 3 difficulty set to 1.000000
 [2013-06-10 14:37:55] Stratum authorisation success for pool 3
 [2013-06-10 14:37:55] Pool 3 http://mint.bitminter.com:8332 alive
 [2013-06-10 14:37:55] Failed to get sessionid in initiate_stratum
 [2013-06-10 14:37:55] Pool 0 difficulty set to 1.000000
 [2013-06-10 14:37:55] Stratum authorisation success for pool 0
 [2013-06-10 14:37:55] Pool 0 http://mint.bitminter.com:8332 alive
 [2013-06-10 14:37:55] Switching to pool 0 http://mint.bitminter.com:8332
 [2013-06-10 14:37:55] Stratum authorisation success for pool 5
 [2013-06-10 14:37:55] Pool 5 http://stratum.btcguild.com:3333 alive
 [2013-06-10 14:37:56] Closing socket for stratum pool 2
 [2013-06-10 14:37:56] Pool 4 stratum session id: ae6812eb4cd7735a302a8a9dd95cf71f
 [2013-06-10 14:37:56] Closing socket for stratum pool 3
 [2013-06-10 14:37:56] Closing socket for stratum pool 5
 [2013-06-10 14:37:57] Stratum authorisation success for pool 4
 [2013-06-10 14:37:57] Pool 4 http://stratum.bitcoin.cz:3333 alive
 [2013-06-10 14:37:57] Binary size for gpu 0 found in binary slot 0: 825208
 [2013-06-10 14:37:57] At 0523bd6a (4290042414 rem. bytes), to begin patching

[energywave]

I'm experiencing a very odd and blocking problem: was mining with CGMINER 3.1.0 on Radeon HD 5750, never had problem, with SHA256 nor Scrypt, all was fine.
At some point I tried CGMINER 3.2.0 and it crashed at start (could only see one line "Started CGMINER 3.2.0" and then crashed).
The odd thing is that from that point over even all other versions of CGMINER do the same!!! I cannot anymore use CGMINER! I've tried with 3.1.1 (that I'm succesfully using on another PC): crash. 3.1.0 that was working well before: crash. Today I tried even 3.2.1: crash.
I did a Dr. Mingw debug for you, hoping to understand what the hell is happening.

Code:

cgminer.exe caused an Access Violation at location 004312d2 in module cgminer.exe Reading from location 072ff1d3.

Registers:
eax=76709102 ebx=0445fd14 ecx=00000000 edx=00000000 esi=0445fc80 edi=00000000
eip=772de1a4 esp=0445fb58 ebp=0445fcd8 iopl=0         nv up ei pl nz na pe nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000202

Call stack:
772DE1A4  ntdll.dll:772DE1A4  ZwWaitForMultipleObjects
76AE6AEB  KERNEL32.DLL:76AE6AEB  WaitForMultipleObjects
0045A362  cgminer.exe:0045A362
0045ACD7  cgminer.exe:0045ACD7
Registers:
eax=00000000 ebx=7fffffff ecx=00000000 edx=00000000 esi=ffffffff edi=0097c6d8
eip=772ddc34 esp=04d5f998 ebp=04d5f9d8 iopl=0         nv up ei pl nz na pe nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000202

Call stack:
772DDC34  ntdll.dll:772DDC34  NtWaitForSingleObject
71F78599  mswsock.dll:71F78599  Tcpip4_WSHGetWildcardSockaddr
75140CCF  WS2_32.dll:75140CCF  select
0041C6B8  cgminer.exe:0041C6B8  socket_full  util.c:1057
0041C6FD  cgminer.exe:0041C6FD  sock_full  util.c:1069
0040F6B0  cgminer.exe:0040F6B0  stratum_rthread  cgminer.c:4962
00459F25  cgminer.exe:00459F25
7670906A  msvcrt.dll:7670906A  _ui64tow
76709147  msvcrt.dll:76709147  iswalnum
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain
XXXXXXXXXXXXXXXXXXXXXX
Registers:
eax=072ff1cf ebx=02008668 ecx=ffb8e50d edx=00000008 esi=01ff2e68 edi=02007c6a
eip=004312d2 esp=0028f4e0 ebp=0028f548 iopl=0         nv up ei pl nz na pe nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00010202

Call stack:
004312D2  cgminer.exe:004312D2  patch_opcodes  ocl.c:178
004333EF  cgminer.exe:004333EF  initCl  ocl.c:738
00430218  cgminer.exe:00430218  opencl_thread_prepare  driver-opencl.c:1332
00419410  cgminer.exe:00419410  main  cgminer.c:7691
004010B9  cgminer.exe:004010B9  __mingw_CRTStartup  crt1.c:244
00401284  cgminer.exe:00401284  WinMainCRTStartup  crt1.c:274
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain
Registers:
eax=00000000 ebx=00000000 ecx=00000000 edx=00000000 esi=00000002 edi=0097afe0
eip=772df6b4 esp=048dfdec ebp=048dff84 iopl=0         nv up ei pl nz na pe nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000202

Call stack:
772DF6B4  ntdll.dll:772DF6B4  ZwWaitForWorkViaWorkerFactory
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain
Registers:
eax=00000000 ebx=00000000 ecx=00000000 edx=00000000 esi=0469fe6c edi=00001cb4
eip=772ddc34 esp=0469fe28 ebp=0469fe90 iopl=0         nv up ei pl nz na po nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000206

Call stack:
772DDC34  ntdll.dll:772DDC34  NtWaitForSingleObject
753A10B4  KERNELBASE.dll:753A10B4  WaitForSingleObject
0FB90B1B  amdocl.dll:0FB90B1B  clGetSamplerInfo
0FB872A7  amdocl.dll:0FB872A7  clGetSamplerInfo
0FB87456  amdocl.dll:0FB87456  clGetSamplerInfo
0FB84362  amdocl.dll:0FB84362  clGetSamplerInfo
0FB96FD6  amdocl.dll:0FB96FD6  clGetSamplerInfo
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain
Registers:
eax=00000000 ebx=04b1f8a4 ecx=00000000 edx=00000000 esi=04b1f810 edi=00000000
eip=772de1a4 esp=04b1f6e8 ebp=04b1f868 iopl=0         nv up ei pl nz na po nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000206

Call stack:
772DE1A4  ntdll.dll:772DE1A4  ZwWaitForMultipleObjects
76AE6AEB  KERNEL32.DLL:76AE6AEB  WaitForMultipleObjects
0045A362  cgminer.exe:0045A362
0045ACD7  cgminer.exe:0045ACD7
753AEE71  KERNELBASE.dll:753AEE71  CreateEventExW
753AEE8C  KERNELBASE.dll:753AEE8C  CreateEventExW
753B3BFE  KERNELBASE.dll:753B3BFE  CreateEventExA
00458630  cgminer.exe:00458630
0041BD00  cgminer.exe:0041BD00  tq_pop  util.c:769
0040F9D0  cgminer.exe:0040F9D0  stratum_sthread  cgminer.c:5053
00459F25  cgminer.exe:00459F25
7670906A  msvcrt.dll:7670906A  _ui64tow
76709147  msvcrt.dll:76709147  iswalnum
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain
Registers:
eax=76709102 ebx=6b619070 ecx=00000000 edx=00000000 esi=029afe90 edi=00000000
eip=772de1a4 esp=029afd68 ebp=029afee8 iopl=0         nv up ei pl nz na pe nc
cs=0023  ss=002b  ds=002b  es=002b  fs=0053  gs=002b             efl=00000202

Call stack:
772DE1A4  ntdll.dll:772DE1A4  ZwWaitForMultipleObjects
76AE6AEB  KERNEL32.DLL:76AE6AEB  WaitForMultipleObjects
6B608229  libusb-1.0.dll:6B608229  windows_clock_gettime_threaded
76709147  msvcrt.dll:76709147  iswalnum
76AE8543  KERNEL32.DLL:76AE8543  BaseThreadInitThunk
7730BF39  ntdll.dll:7730BF39  RtlInitializeExceptionChain
7730BF0C  ntdll.dll:7730BF0C  RtlInitializeExceptionChain

I hope that someone can lead me to the solution.... I'm now using bitminter java client, but I want a scrypt miner and I like so much CGMINER...!
Thank you in advance to who will reply!